EN User manual Dishwasher ZDF 2010
Contents Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ Product description _ _ _ _ _ _ _ _ _ _ _ _ _ Control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Programmes _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Options _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Before first use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 3 4 4 5 5 Daily use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 7 Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ 10 Troubleshooting _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 10 Technical information _ _ _ _ _ _ _ _ _ _ _ _ 13 Environment
– Farm houses – By clients in hotels, motels and other residential type environments – Bed and breakfast type environments. • Do not use water spray and steam to clean the appliance. • The appliance can release hot steam if you open the door while a programme operates. Disposal Warning! Risk of injury. • Do not change the specification of this appliance. • Put knives and cutlery with sharp points in the cutlery basket with the points down or in a horizontal position.
Control panel 1 2 6 1 On/off indicator 2 Programme marker 4 Half load button 5 Start button 3 Indicators 6 Programme knob Indicators 3 5 4 Description End indicator. Salt indicator. This indicator is off while the programme operates. Rinse aid indicator. This indicator is off while the programme operates.
Programme 3) Degree of soil Type of load All Programme phases Options Prewash 1) With this programme you can wash a load with fresh soil. It gives good washing results in a short time. 2) This is the standard programme for test institutes. With this programme you have the most efficient use of water and energy consumption for crockery and cutlery with normal soil. 3) Use this programme to quickly rinse the dishes.
Adjusting the water softener Hard water contains a high quantity of minerals that can cause damage to the appliance and bad washing results. The water softener neutralises these minerals. The dishwasher salt keeps the water softener clean and in good conditions. Refer to the table to adjust the water softener to the right level. It makes sure that the water softener uses the correct quantity of dishwasher salt and water. You must adjust the water softener manually and electronically.
5. To confirm the setting, turn the programme knob until the programme marker is aligned with the on/off indicator. Filling the salt container Caution! Only use dishwasher salt. Other products can cause damage to the appliance. Water and salt can come out from the salt container when you fill it. Risk of corrosion. To prevent it, after you fill the salt container, start a programme. Filling the rinse aid dispenser Caution! Only use rinse aid for dishwashers.
2. Press the on/off button to activate the appliance. Make sure that the appliance is in setting mode. Refer to ’SETTING AND STARTING A PROGRAMME’. • If the salt indicator is on, fill the salt container. • If the rinse aid indicator is on, fill the rinse aid dispenser. 3. Load the baskets. 4. Add the detergent. 5. Set and start the correct programme for the type of load and soil. 1 2 A Loading the baskets A Refer to the supplied leaflet with examples of the load of the baskets.
When you use tablets, that contain salt and rinse aid, do not fill the salt container and the rinse aid dispenser. The rinse aid indicator always comes on if the rinse aid dispenser is empty. 1. Adjust the water softener to the lowest level. 2. Set the rinse aid dispenser to the lowest position. If you stop to use the combi detergent tablets, before you start to use separately detergent, rinse aid and dishwasher salt, do these steps: 1.
Care and cleaning Warning! Before maintenance, deactivate the appliance and disconnect the mains plug from the mains socket. Dirty filters and clogged spray arms decrease the washing results. Make a check regularly and, if necessary, clean them. Cleaning the filters A 5 Put filter (A) to its initial position. Make sure that it assembles correctly under the two guides (D). C B A 1 D 6 Assemble filters (B) and (C). Put them into position in filter (A). Turn the handle clockwise until it locks.
Alarm code Problem • The start indicator flashes continuously. • The end indicator flashes 1 time intermittently. The appliance does not fill with water. • The start indicator flashes continuously. • The end indicator flashes 2 times intermittently. The appliance does not drain the water. • The start indicator flashes continuously. • The end indicator flashes 3 times intermittently. The anti-flood device is on. Warning! Deactivate the appliance before you do the checks.
Problem Possible cause Possible solution The filters are not correctly assembled and installed. Make sure that the filters are correctly assembled and installed. The spray arms are clogged. Remove remaining soil with a thin pointed object. The programme was not applicable for the type of load and soil. Make sure that the programme is applicable for the type of load and soil. Incorrect position of the items in the baskets. Water could not wash all items.
Problem Possible cause The quality of the combi detergent tablets can be the cause. Possible solution • Try a different brand of combi detergent tablets. • Activate the rinse aid dispenser and use the rinse aid together with the combi detergent tablets. Technical information Dimensions Width / Height / Depth (mm) Electrical connection Refer to the rating plate. Voltage 600 / 850 / 610 220-240 V Frequency 50 Hz Water supply pressure Min. / max. (bar / MPa) (0.5 / 0.05 ) / (8 / 0.
www.zanussi.
www.zanussi.
156959660-B-112012 www.zanussi.
