English / 한글 VGA WATER BLOCK ZM-GWB 8800 GT/GTS (G92) ZM-GWB 3850/3870 ◈Please visit our website and watch the ZM-GWB8800GT/GTS (G92), ZM-GWB3850/3870 installation video for easy installation. ※ Please read this manual thoroughly before installation. http://www.zalman.com http://www.zalmanusa.
Table of Contents 1. Precautions 2 2. Components 3 3. Exploded View 5 4. Installation Guide 7 www.zalman.com www.zalmanusa.
Precautions 1) Test the product for leakage away from the system before installing it on the system. Once no leakage is confirmed, proceed with the installation and use. 2) Use approved coolant for computer water-cooling to prevent corrosion. 3) Use coolant tubes listed under the compatibility list. 4) Do not install the product if it interferes with any VGA components. 5) To maintain absolute leak-free operation, this product is not designed to be disassembled.
3. Components ZM-GWB8800GT/GTS (G92) English ① Thermal Pads - 20X78X1T, 7.5X7.5X1T (for FET Contact) - Four(4) 38X11X1T (for RAM Contact) ② Two(2) PVC Washer Plates ③ VGA Water Block Assembly ④ Thermal Grease ⑤ Two(2) Tube Clamps ⑥ Ten(10) Springs ⑦ Ten(10) O-rings ⑧ Nine(9) Nuts ⑨ Nine(9) Nipples ⑩ User’ s Manual ① ④ ③ ⑦ ⑥ ⑨ ② ⑤ ⑧ ⑩ ※ The specifications of any product may change without prior notice to improve performance.
ZM-GWB3850/3870 ① Thermal Pads - Three(3) 32 X 12 X 1T(for RAM Contact) - Four(4) 14 X 14.
4. Exploded View ZM-GWB8800GT/GTS (G92) English Water Block Assembly Nipple O-ring PVC Washer Spring Nut ※ The specifications of any product may change without prior notice to improve performance.
ZM-GWB3850/3870 Water Block Assembly FET Water Block Nipple O-ring PVC Washer Spring Nut 6 ※ The specifications of any product may change without prior notice to improve performance.
5. Installation ZM-GWB8800GT/GTS (G92) English Nipple Install Tap Water Block ZM-GWB3850/3870 Radeon HD 3870 Install Tap Nipple Radeon HD 3850 Install Tap Bolt Radeon HD 3870 Install Bracket Water Block ※ ※ Radeon HD 3870 The specifications of any product may change without prior notice to improve performance.
1) Nipple Installation ① Install the Nipple onto the Install Tap on the base side of the Water Block. Note ·Use a tool such as Long Nose Pliers to firmly tighten the Nipples. ·Radeon HD 3850/3870 users, please refer to the diagram shown on the lower section of page 7 for installation details. 2) Thermal Pad Attachment ① Clean the contact surface of the VGA Chipset completely. ② Attach each Thermal Pad to line up with the Thermal Pad Outlines indicated on the Water Block's base as shown in the diagram below.
Thermal Pad (for FET) Thermal Pad (for RAM) Radeon HD 3870 Thermal PAD Outline English Radeon HD 3850 Thermal PAD Outline 3) Thermal Grease Application Evenly apply the Thermal Grease on the GPU surface that comes in contact with the VGA Water Block. VGA Card Thermal Grease GPU 4) VGA Water Block Installation ① Insert the O-ring into the Nipple. ② Insert the Nipples installed on the VGA Water Block into the Mounting Holes after aligning them.
Note ·Check to see if the Water Block’s base side is in proper contact with the VGA chipset before finishing the installation. ·Assembling the Springs with the Nuts prior to installation will ease the installation process. Nut Spring PVC Washer 5) Tension Control of the VGA Water Block Tighten/loosen the Nuts on the back side of the VGA card to control the tension between the VGA Water Block and the VGA Chipset. Note ·If the Nuts are turned too tightly, then the VGA chipset or VGA card may get damaged.
7) Installation of Tubes and Tube Clamps Plug the tubes over the VGA Water Block’s fittings and install the Tube Clamps. Note ·Hold the VGA card with one hand when plugging the Tube into the Fitting. will ease the installation process. Inlet English ·Use of a tool such as Long Nose Pliers when installing the Tube Clamp Outlet Fitting Inlet Outlet Tube Clamp Fitting ※ The specifications of any product may change without prior notice to improve performance.
Zalman Computer Noise Prevention Systems Stable performance and a noiseless liquid cooling system can both be achieved with the use of Zalman’s CPU Water Block, H.D.D Cooler, Noiseless Case Fan, and Northbridge Water Block. CPU Water Block Heatpipe H.D.