RESERATOR 1 V2 English Version Visit our website (www.zalman.co.kr) and watch the RESERATOR 1 V2 installation video for an installation overview. ※ Please read this manual thoroughly before installation. ※ The specifications of this product and its components may change without prior notice to improve the performance thereof. www.zalman.co.kr www.zalmanusa.
RESERATOR 1 V2 Installation and Operational Notes Installation Notes 1. Make sure that the power source’s output voltage and frequency are compatible with the power input requirements of the water pump before installing(Input voltage and frequency of the water pump are shown on the box and sink cover). 2. Do not place in dusty or humid conditions, under direct sunlight, or near a heat source such as a room heater. 3. Do not drop or subject to excessive force. 4. CPU socket compatibility must be checked. 5.
RESERATOR 1 V2 Table of Contents English Installation and Operational Notes 1. Features 3 2. Specifications 5 3. Installation Overview 6 4. Standard Components & Optional Components 7 5. Installation Guide 9 6. Pump Replacement and External Water Pump Installation 14 7. Zalman Noise Prevention System 17 1.
RESERATOR 1 V2 1. 1 Reserator (Reservoir + Radiator + Water Pump) “Reserator” is a compound word derived from ‘Reservoir’ and ‘Radiator’ - it acts as a reservoir while radiating heat. This product works well with natural convection and integrates a water pump inside for convenience. 1. 2 CPU Water Block (ZM-WB4 Gold) The CPU Water Block incorporates a pure copper base for excellent heat transfer, and has gold plating to prevent corrosion.
RESERATOR 1 V2 2. Specifications English 2. 1 Reserator (Reservoir+Radiator+Water pump) 1) Dissipation Area : 1.274㎡ 2) Weight : 6.5 kg 3) Dimensions : 150(L) x 150(W) x 592(H) mm 4) Material : Anodized Pure Aluminum 5) Max Coolant Capacity : 2.5ℓ 6) Integrated Water Pump : 5 W, Qmax 300 ℓ/h (A type : 230V-50Hz, B type : 120V-60Hz, C type : 220V-60Hz, D type : 110V-60Hz) 7) Maximum Lift : 0.5 m 2.
RESERATOR 1 V2 3. Installation Overview Reserator CPU Water Block (ZM-WB4 Gold) Northbridge Water Block (ZM-NWB1, Optional) VGA Water Block (ZM-GWB3) I/O Bracket Quick Coupling Flow Indicator 6 ※ The specifications of any product may change without prior notice to improve performance.
RESERATOR 1 V2 4. Components 4. 5 Coolant (ZM-G200) 1EA English 4. 1 Reserator 1 Unit 4. 6 PVC Tube 4m 4. 2 CPU Water Block(ZM-WB4 Gold) 1SET Please refer to the separately provided manual for the ZM-WB4 Gold. 4. 7 I/O Bracket 1EA 4. 8 Quick Coupling Insert 2EA 4. 3 VGA Water Block (ZM-GWB3) 1SET Please refer to the separately provided manual for the ZM-GWB3. 4. 4 Flow Indicator 1EA 4. 9 Tube Clamp 2EA 4.
RESERATOR 1 V2 Optional Components ● Northbridge Water Block (ZM-NWB1) This anodized, pure aluminum block is built for high performance cooling, and is designed for Motherboard compatibility with a wide variety of northbridge chipsets. ● VGA RAM Water Block (ZM-RWB1) This VGA RAM Water Block is compatible with GeForce 7800/7900 and ATI X1800/X1900 in need of VGA RAM cooling.
RESERATOR 1 V2 5. Installation Guide English 5. 1 Check for Leaks Before installing the product on a PC, check each Water Block and the Reserator for leaks. 5. 2 Determine the Placement of the Reserator The Reserator’s placement should be determined in relation to the position of the PC. Place it upright next to or slightly above the PC. Note that if the Reserator is placed lower than the PC, the PVC tube’s internal air pressure may prevent proper initial operation. (O) (X) (O) (X) (X) 5.
RESERATOR 1 V2 5. 6 Connect the CPU Water Block and the VGA Water Block PVC Tube CPU Water Block 1) As shown in the diagram, connect the two water blocks with a PVC tube. VGA Water Block 5. 7 Connect the VGA Water Block with Reserator’s Base IN 1) As shown in the diagram, connect one end of the PVC Tube to the VGA Water Block Fitting and fasten with a Tube Clamp. 2) Pull out the PVC Tube through the I/O Bracket hole on the computer case.
RESERATOR 1 V2 5. 9 Connect the Flow Indicator with the Reserator’s Base OUT English 1) Connect one end of the PVC Tube to the Flow Indicator. 2) Insert a Tube Clamp to the other end of the tube, connect a Quick Coupling Insert, then fasten with the Tube Clamp. 3) Connect the Quick Coupling to the Quick Coupling Body on the Reserator’s Base OUT.
RESERATOR 1 V2 5. 11 Confirm Proper Installation 1) Check that the product is placed properly (i.e. conforms to section 5.2). 2) Confirm that the coolant circulation path is correct as shown below. 3) Lightly tug the PVC tube connected to each of the fittings to check for loose ends. Reserator OUT Flow Indicator Water Pump Absorb Heat Reserator Reserator IN CPU Water Block N/B Water Block VGA Water Block Radiate Heat 5. 12 Fill the Coolant 1) Take off the Sink Cover on top of the Reserator.
RESERATOR 1 V2 5. 13 Leakage Inspection and Test Run ※ The specifications of any product may change without prior notice to improve performance. English 1) Turn off the PC’s power completely before starting leakage inspection. 2) Turn on the water pump. If the coolant does not circulate properly, turn the pump on and off repeatedly to eliminate air bubbles. 3) Check each fitting for leaks. If there is a leak, circuitry and other components may short circuit and malfunction, so be careful.
RESERATOR 1 V2 6. Pump Replacement and External Water Pump Installation If the integrated water pump is broken or you need a water pump with higher capacity, you can replace the water pump or install an external water pump as shown below. 6. 1 Separate the Integrated Water Pump Sink Base 1) Separate the sink base Take off the sink base from the product as shown in the diagram.
RESERATOR 1 V2 5) Take out the Power Cable Pull the Water Pump power cable out through the Cable Hole. Sealing Bolt A Water Pump English 6) Remove the Cable Fitting Take the Cable Fitting out of the hole as shown in the diagram by using a screwdriver or an awl. 7) Remove the Integrated Water Pump Pull the Water Pump off the Sink Base as shown in the diagram.
RESERATOR 1 V2 6.2 Installing the External Water Pump CPU Water Block (ZM-WB4 Gold) Northbridge Water Block (ZM-NWB1, Optional) VGA Water Block (ZM-GWB3) Flow Indicator External Water Pump After determining the placement of the External Water Pump, check the components that create a path as shown above. It is recommended that the installation is done in such a manner. 6.
RESERATOR 1 V2 7. Zalman Noise Prevention System Noiseless Power Supply Heatpipe HDD Cooler Noiseless Case Fan English Stable performance and noiseless liquid cooling system can both be achieved with the use of Zalman’s Noiseless Power Supply, Hard Disk Cooler and Noiseless Case Fan, Northbridge Water Block.
