User's Manual CNPS14X Intel Socket 2011 / 1366 / 1156 / 1155 / 775 CPU Core i7 Extreme Core 2 Extreme Core i7 Core 2 Quad Core i5 Core 2 Duo Core i3 Pentium Dual-Core Pentium D Pentium 4 Celeron D AMD Socket FM1 / AM3+ / AM3 / AM2+ / AM2 CPU Zambezi Llano Phenom II Phenom Athlon II Athlon X2 Athlon FX Athlon Opteron Dual-Core Opteron Sempron To ensure safe and easy installation, please read the following precautions. www.ZALMAN.com Ver 1.
1. Precautions 1) Avoid inserting objects or hands into the fan while it is in operation to prevent product damage and injuries. 2) Do not ingest the Thermal Grease, and avoid its contact with skin and eyes. If contact is made with skin, wash off with water. If ingested or irritation persists, seek medical attention. 3) To prevent possible injuries, gloves must be worn while handling this product. 4) Excessive force exerted on the fan may cause damage to the fan and/or system.
. Components Manual Cooler Backplate Nuts Side Caps Loading Block Clip A Manual Clip B (Optional Fan) Silver Bolts A(4mm) Silver Bolts B(3mm) (Socket 1366/1156/1155/775/AMD) (Socket 2011) Double-sided Tape WWW.ZALMAN.
. Installation Requirements 1) Space Requirements The cooler’s installation requires an unobstructed space of 140mm(length), 126mm(width), and 160mm(height), with the CPU as a central reference point. Please check if components such as ODDs and PSU protrude into the required space. 2) Air Guide Removal Air guides on enclosures must be removed before the cooler’s installation since they protrude into the cooler’s required space.
. Installation A. Clip A Installation ※ Install the clip A according to a user socket as shown in the image. - Slightly loosen the bolts, insert the clip A between the cover and the base, and then fasten it with the bolt. Intel Socket Clip A Installation A AMD Socket Clip A Installation B Caution Please note that the connection directions of the clip A are different according to sockets.
B. Nuts and Side Caps ※ Intel Socket 2011 Installation does not require the Nuts and Side caps. Intel Socket 1366/1156/1155/775 AMD Socket FM1/AM3+/AM3/AM2+/AM2 - Install Bolts to the Backplate according to - Install Bolts to the Backplate according to the Socket Type and secure with Side Caps. the Socket Type and secure with Side Caps.
C. Double-sided Tape and Loading Block Installation ※ Intel Socket 2011 Installation does not require the Double-sided Tape and Loading Block. ※ Intel Socket 1366/1156/1155 Installation does not require the Loading Block. Intel Socket 1366/1156/1155 - Attach Double-sided Tape to the center of the Backplate and remove the Double-sided Tape’s Cover. AMD Socket FM1/AM3+/AM3/AM2+/AM2 Intel Socket 775 ① Remove the Sticker Cover from the Lower Tier of the Loading Block and attach it to the Backplate.
D. Backplate Installation ※ Intel Socket 2011 Installation does not require the Backplate. ① Take away the fixed Clip support from the motherboard. /B M /B - Align the Backplate’s nuts with motherboard’s clip support holes, attach it to the back side of the motherboard. AMD Socket FM1/AM3+/AM3/AM2+/AM2 M Intel Socket 1366/1156/1155/775 M /B ② Align the Backplate with motherboard’s clip support holes, attach it to the back side of the motherboard WWW.ZALMAN.
E. Cooler Installation ① Apply a suitable amount of the included Thermal Grease on the CPU’s surface. Intel or AMD CPU ② Place the bolt on the connection position of the clip A, adjust the bolt slightly, and then fasten it with a Spanner. (Use the designated bolts for each socket.
③ Connect the cooler’s 4-pin connector to the motherboard’s CPU Fan header. Caution After installing, be sure to activate the PWM control mode in BIOS on the motherboard. M/B F. Optional Fan Installation (Optional) ※ To install an optional fan, you should purchase it separately. Hang the fan clips on the housing hole of the optional fan and on the grooves at the end of both pins of the cooler. (You can install a maximum of two 140 mm fans.) Option Fan(ZM-F4) Clip B [One Optional Fan] WWW.ZALMAN.
