Installation Instructions

ManualsBrandsZ-Wave.Me ManualsSmart HomeZ-Uno 2 - Z-Wave prototyping board

PWM 1

I2C SDA

I2C SCL

ANT

LED

PWM 2

PWM 4

PWM 3

INT 1

INT 0

ADC 3

ADC 2

ADC 1

ADC 0

RX 0

TX 0

RX 1

TX 1

MOSI

MISO

SCK

micro

USB

Z-Wave chip

Wire antenna

User LED

LED

Service LED

User LED

External connector

Service

GND

3V3

7-18V

Reset

Service

Here are a few steps to help you get started:

1. Unpack your Z-Uno 2

2. Connect the board to the USB port of your computer

3. Conrm the LED is blinking. That’s because Blink demo sketch is already loaded inside

4. Open your Z-Wave controller user interface

5. Start Inclusion (Add) mode on your controller

6. Start Learn Mode on Z-Uno 2 using triple click on the Service Button

7. Conrm the device gets included in the Z-Wave network

8. Check the sketch functionality — changing dimmer value should change LED blinking rate

9. Congratulations! Your Z-Uno 2 is up and running

Thank you for purchasing Z-Uno 2!

Z-Wave Transceiver Silicon Labs ZGM130S

Wireless Range Min. 40 m indoor in direct line of sight

Dimensionst 39 x 20 x 16 mm

Frequency range

(865...869 MHz): Europe (EU) [default], India (IN), Russia (RU),

China (CN), South Africa (EU), Middle East (EU)

(908...917 MHz): America, excluding Brazil and Peru (US)

[default], Israel (IL)

(919...921 MHz): Australia/New Zealand/Brazil/Peru (ANZ),

Hong Kong (HK), Japan (JP), Taiwan (TW), Korea (KR)

1. Download the latest Arduino IDE from

https://www.arduino.cc/en/software

2. Follow instructions on

https://z-uno.z-wave.me/arduino-install

to install Z-Uno 2 package for Arduino IDE

and Z-Uno 2 drivers for your platform

3. Update your Z-Uno 2 board to the latest version, using «Burn Bootloader» menu item

4. You can found many basic and advanced examples on https://z-uno.z-wave.me/examples/

5. Explore a whole new world of knowledge on http://z-uno.z-wave.me/getting-started/

6. Create new awesome devices, already compatible with more than 1300 existing Z-Wave

products!

1. Download the latest VS Code from

https://code.visualstudio.com/download

2. Follow instructions on

https://z-uno.z-wave.me/vs-code-install

to install Z-Uno 2 package for VS Code

and Z-Uno 2 drivers for your platform

Start writing sketches

with Arduino IDE with VS Code

Developed by Smart Systems Ltd

42 Bolshoy boulevard,

Skolkovo Innovation center,

143026 Moscow, Russia

Produced by Smart Devices Ltd

build. 10А/1, 1905 Goda str.,

123022, Moscow, Russia

z-uno@z-wave.me

Summary of content (6 pages)

PAGE 1
Thank you for purchasing Z-Uno 2! Here are a few steps to help you get started: 1. Unpack your Z-Uno 2 2. Connect the board to the USB port of your computer LED LED Service 0 1 2 24 25 3 4 5 6 7 8 Reset 7-18V 5V GND 3V3 SCK MISO MOSI TX 0 RX 0 ADC 0 ADC 1 ADC 2 ADC 3 TX 1 RX 1 micro USB Z-Wave chip 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 User LED Service LED 3. Confirm the LED is blinking. That’s because Blink demo sketch is already loaded inside 4. Open your Z-Wave controller user interface 5.
PAGE 2
Blink Sample Code FCC statement // initial period of the blink is 1 second Z-Uno FCC ID: 2ALIB-ZMEZUNO2 byte dimmerValue = 100; // in 10 ms This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
PAGE 3
2.2 List of applicable FCC rules FCC Part15 Subpart C, Section 15.249 2.3 Summarize the specific operational use conditions The information in this article, including the URL for reference, if there is any change, without prior notice. Documents are provided by the current version without any guarantee responsibility, including merchantability, suitable for any particular purpose or noninfringement guarantees, and any guarantees presented by any proposal, specification, or sample mentioned elsewhere.
PAGE 4
peripheral, the instructions furnished the user manual of the end-user product shall include the following or similar statement, placed in a prominent location in the text of the manual: Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 5
OEM INTEGRATION INSTRUCTIONS: If embedded in another product, the module must be installed by an OEM in the host equipment such that 20 cm is maintained between the antenna and users, and the transmitter module may not be co-located with any other transmitter or antenna. The module shall be only used with the internal antenna(s) that has been originally tested and certified with this module. As long as 3 conditions above are met, further transmitter test will not be required.
PAGE 6
user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. 2.