User Manual ZX2 : ZX Series Server Rugged Rack Mounted Workstations & Servers for Deployed Applications Z Microsystems, Inc. · 9820 Summers Ridge Road, San Diego, CA 92121 · T: 858.831.7000 · F: 858.831.7001 · www.zmicro.
REGULATORY Regulatory Information WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED AC PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS ALL THREE PRONGS CAN BE FULLY INSERTED 1. Use the power and video cables supplied with the product to help prevent interference with radio and television reception. The use of cables and adapters may cause interference with electronic equipment in the vicinity of this unit. 2.
TABLE OF CONTENTS Table of Contents Section Page 1.0 Product Overview............................................................................................................................................................ 4 1.1 About This Manual.............................................................................................................................................. 4 1.2 Product Overview...............................................................................................
Product Overview 1.0 Product overview SAFETY PRECAUTIONS This section will provide information and assistance with the following topics: • About This Manual DANGER: To avoid shock hazard: • Product Overview • Do not remove the covers around the ZX2 Server. 1.1 About This Manual This product manual will help you through the installation, setup, and operation of your ZX2 Server.
Product Overview 1.2 Product Description ZX2 The ZX2 Station is a low–profile, rack mountable, computing and graphics processing powerhouse. At only 3.45” (2U) high by 20 inches deep, this compact, lightweight, rugged workstation gives back valuable rack space and delivers a flexible and high–performance computing solution for demanding mission–ready applications.
SETUP 2.0 SETUP This section will provide information and assistance with the following topics: • ZX2 Assembly parts WARNING Using assembly hardware that does not match specifications may damage internal components. • ZX2 Cable Connections Outline • ZX2 Connection Setup 2.1 Shipment Contents Ensure all of the following parts are included in the package received from Z Microsystems. Verify all parts have not been damaged during shipment.
SETUP 2.3 ZX2 Connections Guide Preparations Required Cables/Connectors In preparation to setting up and connecting the ZX2, turn off the electrical power to your computer. • Power Supply Cable (AC or DC option) • Video Signal Cable (DVI, BNC) • Serial I/O Connector (USB Type B-A) Shown here are typical customer specific examples. MOUSE PORT AC/DC POWER CONNECTORS KEYBOARD PORT PRINTER PORT AUDIO PORTS USB 2.0 PORTS NETWORK ETHERNET PORT MONITOR PORT **Other ZX2 Server configurations available.
COnfigurations 3.0 Configuring your zx2 station This section will provide information and assistance with the following topics: • Updating ZX2 modules and configurations Required Tools Preparations • Removing/Re-installing Lockable Face Plate Cover In preparation to any configurations change to the ZX2, turn off the electrical power to the ZX2 serve and your computer.
COnfigurations 3.3 Changing or re-installing a pci card 1. Use a Philips screwdriver to remove t h e a t t a c h m e n t s c r e w s to t h e s m a l l, black retainers located around the card. Remove retainers with your fingers. 2. Using a Philips screwdriver, remove the attachment screws from the card placeholder plate. 3. Carefully and gently pull the PCI card away from the unit. Be very careful not to bend or t wist the card as damage may occur. 4.
COnfigurations 3.5 Removing a power supply module NOTE: If one of the power supply modules is removed, then the system will still operation with only one remaining power supply. WARNING: A failed power supply will be identified by an audible alarm. 1. Using a Flathead screwdriver, remove both screws from the rear top plate of the Power Supply module 3. Gently but firmly continue to pull the Power Supply module out of the ZX2station. 2.
COnfigurations 3.7 removing the lockable face plate cover 1. Using the provided key, turn to the right to unlock the face plate cover. 2. Using a Flathead screwdriver, release the attachment screws on either side of the face plate cover. 3. Pull the right side of the face plate cover away from the right support bracket. NOTE: The Lockable Face Plate Cover is an option available only to certain models. 4.
operations 4.0 Operations This section will provide information and assistance with the following topics: • Powering up the ZX2 Station • ZX2 Status Information & Indicators • Inserting & Removing Tranzpak2 Storage Modules 4.1 Powering on the ZX2 station 1. To power up the ZX2, press and hold (about 1 second) the Power Supply Switch at the center right side of the unit. 2. T he display may pos sibly indic ate items that require attention.
operations 4.3 Removing the Tranzpak2 storage Module 1. Slide the locking catch towards the right to allow the locking handle to spring open. 2. The locking handle will swing out. 4. Gently but firmly begin to pull the TranzPak2 module out as it slides off the grounding contacts. 5. When the TranzPak2 module is fairly extracted, lift and support the module away from the ZX2. 3. Push the locking handle to the lef t. This will disconnect the TranzPak2 from the rear connector. 4.
Maintenance 5.0 Maintenance WARNING This section will provide information and assistance with the following topics: • Cleaning the ZX2 Server Be sure to turn off the power before you perform any maintenance on the server. • Replacing the ZX2 Air Filter 5.1 Cleaning the ZX2 Server Unplug the ZX2 server from the power outlet before cleaning. WARNING • To clean the surface of the ZX2, lightly dampen a soft, clean cloth with water or mild detergent and wipe the surface gently.
Troubleshooting 6.0 Troubleshooting the ZX2 Station This section will provide information and assistance with the following topics: • Troubleshooting Topics for the ZX2 Station • Frequently Asked Questions about the ZX2 Station Troubleshooting Topics In the event that the ZX2 Server experiences technical problems please refer to the following troubleshooting topics for potential resolution.
Customer Support 7.0 Customer support NOTE: If possible, stay by the computer. NOTE: More help, late-breaking news, and The Z Microsystems Technical Support details of the latest accesories for Z Micro Representative may wish to go through the products can be found on our website at : problem over the telephone. www.zmicro.com Technical Support If you are unable to correct the problem yourself, contact Z Microsystems at: Phone: Fax: Website: Email: (858) 831-7040 (858) 831-7001 www.zmicro.
Customer Support 7.1 Replacing Parts for the ZX2 Station If the Z Microsystems Technical Support Engineer determines that the product needs to be replaced, a Customer Service Representative will issue a Return Material Authorization (RMA) number. An RMA number is required to return a product to Z Microsystems, regardless of the reason for the return.
Appendix 8.0 Appendix 8.1 Technical Specifications for the ZX2 Station The ZX Series Servers are meticulously engineered to be adaptable and suited for an array of field operations and applications. These are standard ZX Series specifications. Other configurations may cause specifications to vary.
APPENDIX 8.2 Mechanical outlines FOR the ZX2 Station 8.2.
FRONT ISO VIEW 8.2.1 ZX2 Station (Front PAnel) 0 3.45 .859 2.609 3.234 3.45 18.3 1.15 0 .54 3.67 6.79 9.92 19.00 MOUNTING HOLES (SLIDE RAILS NOT INSTALLED) 8.2.2 ZX2 Station - Rear view OF (AC/DC Power supply) THIS DOCUMENT IS THE PROPERTY Z Microsystems 20.00 ESS OTHERWISE SPECIFIED MENSIONS ARE IN INCHES TOLERANCES ARE: 1 05 .80 FRACTIONS 1/32 ANGLES 1 O NOT SCALE DRAWING 63 Z MICROSYSTEMS, INC. AND CONTAINS INFORMATION WHICH IS PROPRIETARY TO Z MICROSYSTEMS, INC.
Z Microsystems, Inc. 9820 Summers Ridge Road San Diego, CA 92121 Phone: (858) 831-7000 Fax: (858) 831-7001 Website: www.zmicro.com Copyright 2012 Z Microsystems, Inc. All Rights Reserved Z Microsystems, Inc. · 9820 Summers Ridge Road, San Diego, CA 92121 · T: 858.831.7000 · F: 858.831.7001 · www.zmicro.
