H08017 JMY
⑨ ① ④ ⑩ ⑩ ⑧ ⑧ ⑧ ⑤ ⑨ ⑥ ② ⑩ ⑩ ③ Electronic fireplace individually packaged ⑦ ⑦ A B 44PCS C 44PCS 8*40 24PCS D E 16PCS F 16PCS 3*12 16PCS G 3.
1 2 2000*340 1PS 5 3 1968*340 1PS 6 475*340 1PS 9 550*340 1PS 7 475*340 1PS 10 644*485 2PS 4 632*315 4PS 550*340 1PS 8 1968*60 2PS 670*80 3PS
Ｈａｒ ｄｗａｒ ｅ ｉ ｎｓｔ ａｌ ｌ ａｔ ｉ ｏｎ ｄｅｍｏｎｓｔ ｒ ａｔ ｉ ｏｎ ＮＯＴＥ： Ｐｌ ｅａｓｅ ｍａｋｅ ｓｕｒ ｅ ＂Ａ＂ｈａｒ ｄｗａｒ ｅ ｔ ｉ ｇｈｔ ｅｎｅｄ ａｎｄ ｃａｎ＇ ｔ ｂｅ ｐｕｌ ｌ ｅｄ ｏｕｔ ！ Ⅰ Ⅲ Ⅱ Ⅳ Scan QR code f or assembl y vi deo
① ① ② ⑦ ⑦ put A on board ①② put C on board ②⑦
② ④ ③ put A on board ③④ put C on board ③④ put D on board ③④ put G on board ③④
③ ⑤ Roate 180° ⑤ put A on board ⑤ put C on board ⑤ put D on board ⑤ put G on board ⑤
④ ⑥ Roate 180° ⑥ put A on board ⑥ put C on board ⑥ put D on board ⑥ put G on board ⑥
⑤ Roate 180° ⑦ ② ⑦ ② ⑦ Make sure the arrow on the screw align to the hole on the side.
⑥ ⑧ ⑧ ⑥ ⑧ ⑤ Make sure the arrow on the screw align to the hole on the side.
⑦ ⑧ ⑧ ⑥ ⑧ ⑤ ② put B on board ⑤⑥⑧ Make sure the arrow on the screw align to the hole on the side.
⑧ ④ ⑥ ⑧ ⑧ ② ⑤ ⑦ ③ ⑦ put B on board ③④⑦ Make sure the arrow on the screw align to the hole on the side.
⑨ ⑨ ④ ⑧ ⑧ ⑥ ⑨ ⑧ ⑤ ② ③
⑩ Make sure the arrow on the screw align to the hole on the side.
put E on board ⑨ put F on board ⑨
④ ① ⑥ ⑩ ⑩ ⑤ ② ⑩ ③ ⑩
⑩ ① ⑩ ⑥ ② ⑩ ⑩ ③ ⑤ ④
① ⑨ ⑨ ④ LE D
④ ① ③ put H on board ③④
LED Light If you can’t let the lights work successfully, please check the following: 1. Please check the direction of the connect, try it in the opposite direction, according to the following picture. 2. Please check the remote control, it need you to tear down the plastic septum before use it. 3. Don’t let the remote control too far from the receiver, make sure there is no obstruction between them.
