Spectrum Z™510 3D Printer Hardware Manual Rev J; Part Number 09537; August 2007 www.3dpuser.
Spectrum Z™510 3D Printer Hardware Manual TABLE OF CONTENTS 1 Overview........................................................................................................... 1.1 Use Of Equipment .................................................................................... 1.2 Manual Sections ....................................................................................... 2 What's New.......................................................................................................
8.2 8.3 8.4 8.5 8.6 8.7 8.8 Change Print Heads ................................................................................. Purge Print Head ...................................................................................... Check Powder Level................................................................................. Drop Feed Piston...................................................................................... Fill Bed...................................................................
Spectrum Z™510 3D Printer Hardware Manual Overview 1 Overview 1.1 Use Of Equipment Z Corporation's Equipment, and use of the Equipment, may be subject to limitations imposed under patents licensed to or owned by Z Corp., and is to be used solely for the fabrication of appearance models and prototypes using new Z Corporation-supplied consumables from Z Corporation or its authorized distributors in the original packaging. Other uses may be restricted; contact Z Corporation for further information.
Spectrum Z™510 3D Printer Hardware Manual Overview • Using the ZPrint™ Firmware and Software. This section gives you an overview of how to download firmware and how to set up a build on the ZPrint Software. For more information about the software and its features, please refer to the ZPrint Software Manual. • Post-Processing the Part. This section guides you through removing your printed part, depowdering, and infiltrating the part with resin to improve strength and finish.
Spectrum Z™510 3D Printer Hardware Manual What's New 2 What's New This section briefly describes what’s new in this version of the Spectrum Z510 3D Printer Hardware Manual. • New firmware installation instructions. The function of firmware is to test and check certain diagnostics related to printer cleaning/lubrication maintenance prior to each build. When the firmware detects that this type of maintenance is required, a message is displayed in the ZPrint software and on the printer control panel.
Spectrum Z™510 3D Printer Hardware Manual Introduction 3 Introduction 3.1 How It Works The 3D Printer System is based on the Massachusetts Institute of Technology's patented 3DP™ (3D Printing) technology. The software first converts a three-dimensional design built using 3D CAD into cross sections or slices that are between 0.0035" - 0.004" (0.0875 - 0.1 mm) thick. The printer then prints these cross-sections one after another from the bottom of the part to the top.
Spectrum Z™510 3D Printer Hardware Manual Introduction Step 5: The feed piston moves up one layer, the build piston moves down one layer, and the process is repeated. Step 4: As the gantry traverses right to left, the print head prints the part cross-section. The printer employs several techniques to quickly build parts. First, binder solution is applied in a higher concentration around the edges of the part, creating a strong "shell" around the exterior of the part.
Spectrum Z™510 3D Printer Hardware Manual Introduction axis (the print heads’ direction of travel), bands across the x or the "slow" axis (the gantry direction of travel) and laminated layers along the z-axis. This discussion only applies to untreated parts; once parts are infiltrated, they uniformly take on the strength characteristics of the infiltrating material. • Accuracy. The accuracy of the system depends on the materials you choose.
Spectrum Z™510 3D Printer Hardware Manual Introduction 3.2 System Components Z510 3D Printer ZD5 Powder Recycling System 3.3 Printer Components www.3dpuser.
Spectrum Z™510 3D Printer Hardware Manual Introduction 3.4 Printer Control Panel 3.5 Internal, Printer Assembly and Service Station Components Internal Components www.3dpuser.
Spectrum Z™510 3D Printer Hardware Manual Introduction Printer Assembly with Carriage Insert Service Station www.3dpuser.
Spectrum Z™510 3D Printer Hardware Manual Introduction 3.6 ZD5 Powder Recycling System Click ZD5 Depowder Unit to see the User Manual for this unit and other accessories available for your 3D Printers. www.3dpuser.
Spectrum Z™510 3D Printer Hardware Manual Introduction 3.7 Z510 Powders, Accessories and Tools Refer to the following table regarding powder types available for use with the Z510 Printer. Click Applications for additional information regarding high performance, casting, specialty materials, and infiltrants. Click MSDS to see information about material storage and safety precautions on the 3DP™ User Website.
Spectrum Z™510 3D Printer Hardware Manual Introduction zp®140 High Performance Plus Powder zp140 is a multi-purpose material system that offers significantly easier post-processing and exceptional color performance. The "Plus" in our High Performance powder is the new Water Cure process. • Water Cure – The easiest and safest postprocessing available. Only tap water is required to seal and strengthen your printed parts, and it has the lowest cost per in³.
Spectrum Z™510 3D Printer Hardware Manual Introduction Tool Kit Document 09523 Post Processing Tools Use Instructions. Service Form Documents to be completed and returned to Z Corp. 1. Scraper, 5” Wide Utility 2. Brush, Double-Ended 3. Brush, 2” China Bristle 4. Brush, Acid 5. Brush, Toothbrush Style 6. Scraper, 3” Wide Utility 1. No longer included in kit 2. Extra Screws 3. Syringe for cleaning Service Station 4. Syringe Tube and Fitting 5. Grease Gun, Mini for 3oz. Cartridge 6.
Spectrum Z™510 3D Printer Hardware Manual • Introduction New Vacuum Attachment - fits the Z510 3D Printer vacuum hose and attaches to the side of the feed box to capture airborne powder when powder is being added to the feed box. 3.9 ZPrint Software Installation The ZPrint Software is the file processing tool that sends information from the user's workstation to the 3D Printer. Please refer to the ZPrint Software Manual for installation and use instructions. www.3dpuser.
Spectrum Z™510 3D Printer Hardware Manual Quick Start Guide 4 Quick Start Guide This section is a short step-by-step process of how to get a print job running on your printer. For a more detailed explanation, see Routine Operations, Using the ZPrint Firmware and Software, and Post Processing the Part. 4.1 Preparing The 3D Printer 1. Fill the feed box with powder. 2. With the printer offline, spread powder over build area by pressing the Spread button on the control panel for four spreads.
Spectrum Z™510 3D Printer Hardware Manual Quick Start Guide 4. Check the binder bottles. Fill if necessary. 5. Check the wash fluid and the waste fluid. Fill the wash fluid and dispose of the waste fluid. 6. Put printer online by pressing the Online button on the control panel. Technical Tip LEAVE THE PRINTER ON! This allows the printer to perform a periodic self maintenance. www.3dpuser.
Spectrum Z™510 3D Printer Hardware Manual Quick Start Guide 4.2 Preparing the Build in ZPrint Software 1. Launch ZPrint and open or import your file(s). 2. Orient and scale the file, if needed. www.3dpuser.
Spectrum Z™510 3D Printer Hardware Manual Quick Start Guide 3. Open the File menu and select 3D Print Setup. In the 3D Print Setup dialog, select your Printer, Powder Type, and Layer Thickness options. 4. Select 3D Print on the File Menu or click the 3D icon on the Toolbar. Choose your settings in the Printing Options dialog and click OK. Proceed through the series of preparation dialogs that appear before the build starts. 4.3 Removing the Part 1. Wait for part to complete printing.
Spectrum Z™510 3D Printer Hardware Manual Quick Start Guide 3. Fine depowder part and post-process as needed. www.3dpuser.
Spectrum Z™510 3D Printer Hardware Manual Routine Operations 5 Routine Operations The routine maintenance tasks described in this chapter should be performed before every build. 5.1 Preparing the Build Area IMPORTANT Use only powder supplied by Z Corporation. Use of any other material may impact the performance and/or safety of your 3D Printer System and will void warranty of equipment. 1. Preheat printer, if needed.
Spectrum Z™510 3D Printer Hardware Manual Routine Operations 6. Hold the Build UP button until the build piston raises. The build piston will expose the build plate holders. 7. Place build plate on top of holders. Make sure build plate is secure. Press any button on the control panel to lower the build piston. 8. Fill the feed box with powder. First empty the powder from the overflow bin and then add fresh powder if needed. 9.
Spectrum Z™510 3D Printer Hardware Manual Routine Operations 10. Close the top cover of the printer. Fill the build area with powder by pressing and holding the Spread button on the control panel for four complete spreads. This will initiate the Fill Bed mode. The LCD will display "Filling bed; Online to cancel." 11. Lift the top cover of the printer and vacuum loose powder from the area surrounding feed and build box. Technical Tip Keep powder containers closed when not in use to keep powder dry.
Spectrum Z™510 3D Printer Hardware Manual Routine Operations 2. With the Service Station exposed, rinse rubber Parking Cap with distilled water (If needed, remove rubber Parking Caps and rinse under running water). Wipe dry with paper towel. PLEASE NOTE: Make sure the Parking Caps are sitting flat in their holders. 3. Clean squirt manifold holes by carefully inserting the luer lock needle into the squirt manifold holes. DO NOT PRESS HARD. The needle should go in. Clean one by one all six holes.
Spectrum Z™510 3D Printer Hardware Manual Routine Operations 5. Wipe metal spit cover with damp paper towel. 6. Close top cover and press OK to repark on the software. 5.3 Checking Fluid Levels 1. Open front cabinet tray. 2. Check wash fluid level. If it is less than half full, refill wash fluid bottle. www.3dpuser.
Spectrum Z™510 3D Printer Hardware Manual Routine Operations 3. Check waste fluid. If it is half full, empty fluid. Empty contents in accordance to local or company safety regulations. Close front cabinet tray. WARNING Do not recycle waste solution. The waste is contaminated with powder and use of this waste in the your 3D Printer will clog the fluid system. Use only binder and wash fluid supplied by Z Corporation.
Spectrum Z™510 3D Printer Hardware Manual Routine Operations Refer to the following links to learn about other periodic maintenance tasks. The following tasks should only be performed when prompted to by ZPrint or when you see a message on your 3D Printer LCD. Fast Axis Lubrication Slow Axis Lubrication Piston Screws Lubrication Change Print Heads www.3dpuser.
Spectrum Z™510 3D Printer Hardware Manual Using the ZPrint Firmware and Software 6 Using the ZPrint Firmware and Software This chapter will briefly describe firmware and how to install it from the 3DP User Website, how to set up a build, check the build settings, and print. For more information about the features in the ZPrint Software, please refer to the ZPrint Software Manual. 6.1 Firmware Overview Firmware tests and checks certain diagnostics related to printer maintenance prior to each build.
Spectrum Z™510 3D Printer Hardware Manual Using the ZPrint Firmware and Software • Orient parts so delicate features are supported in the z-axis, i.e. keep the attaching feature directly below the fragile features. If a delicate feature is only supported by unprinted powder the chances of breaking that small feature during depowdering is greatly increased. • When building delicate parts use the "Fixture" function to cradle the part. Raising the part 0.25" (6.
Spectrum Z™510 3D Printer Hardware Manual Using the ZPrint Firmware and Software 6.5 Part Orientation 6.5.1 Parts Containing an Opening or Hollow Area If the part has an opening or is hollow, place the opening or hollow side up. This will allow for the removal of powder during the depowdering process. 6.5.2 Parts Containing Overhangs • Unsupported overhangs should be placed on the left hand-side and as close to the build plate as possible.
Spectrum Z™510 3D Printer Hardware Manual Using the ZPrint Firmware and Software • Slice viewing allows you to view the cross sections of the part to identify any errors in the file. • Collision detection will scan through the slices and report the layer in which part overlapping is found. Follow the steps below to check your build settings. 1. Choose the 3D Print Setup on the File menu, or click the icon on the Toolbar. 2.
Spectrum Z™510 3D Printer Hardware Manual www.3dpuser.
Spectrum Z™510 3D Printer Hardware Manual Post-Processing the Part 7 Post-Processing the Part 7.1 Tips on Gross and Fine Depowdering • For additional information regarding post-processing, click Applications to go to the 3DP™ User website, or Knowledge Base to use our searchable knowledge base on the website. • Become familiar with where the parts are placed and how they are oriented in the build box so you do not accidentally bump or brush against a fragile part during the depowdering process.
Spectrum Z™510 3D Printer Hardware Manual Post-Processing the Part Soft Horsehair Brush: This brush has very soft bristles and assists the user with the gross depowdering process. Brushing powder away from the part is a useful technique prior to the vacuuming step. Stiff Detailing Brush: This brush has very stiff bristles, which is useful for scrubbing caked powder out of tight areas of a part. The brush is also used for removing fringing from color part surfaces.
Spectrum Z™510 3D Printer Hardware Manual Post-Processing the Part 7.3 Removing the Finished Part After the build is complete, remove the finished parts from the build box as follows: 1. Leave the part in the bed for approximately 30-60 minutes. Take a moment to look at the computer screen and determine exactly where parts lie in the build box. 2. Take the printer offline by pressing the Online button and lift the top cover. 3. Press the Feed DOWN button to lower the feed piston. 4.
Spectrum Z™510 3D Printer Hardware Manual Post-Processing the Part 6. To gain access to the sides of the parts, raise the build piston by holding down the Build UP button. 7. When finished, you may remove the part by hand or press the Build UP button on the control panel. When it stops moving, press Build UP one more time to initiate the unload feature. The build plate will now be exposed and easy to lift off the build envelope. 8. Place a tray on the top of the feed area.
Spectrum Z™510 3D Printer Hardware Manual Post-Processing the Part 7.4 Depowdering the Part 1. Place parts inside the depowdering station. 2. Turn on the vacuum cleaner. 3. Turn on the air compressor. 4. Change the air pressure as needed and check the pressure with your hand before applying air on the part. Technical Tip The air pressure on your depowdering station is adjustable. For bulky parts, turn the air pressure up. For delicate parts, turn the air pressure down. www.3dpuser.
Spectrum Z™510 3D Printer Hardware Manual Post-Processing the Part 7.5 Drying the Part Although the part can be handled when it is not completely dried, the part reaches full strength when dried. Placing the part in an oven at temperatures less than 200° F (93°C) for 2-4 hours will dramatically increase the strength of the part. This is only recommended for high definition composite powders. If using the removable build plate, remove the part from the build plate before placing in the oven.
Spectrum Z™510 3D Printer Hardware Manual 7.6.1 Post-Processing the Part Using Paraplast X-TRA Wax Paraplast X-TRA is a low viscosity, general purpose, infiltration wax formulated to melt at very low temperatures (122° F or 50° C) and strengthen parts. This material cures rapidly and enhances the vibrancy of color parts. Paraplast is available in a case of eight 2.2 lb. (1 kilogram) bag of chips. Paraplast X-TRA Wax can be used in both the ZW3 and ZW4 Waxers.
Spectrum Z™510 3D Printer Hardware Manual Post-Processing the Part • Label disposal materials. • Wear dust mask when sanding finished parts. General Application Notes • Part should be fully dried before applying resin. Resin reacts with water and produces heat. If the part is not dried, it will heat up the part and produce gas that may be an irritant to the mucous membranes. • Material can be brushed, dipped or dripped. • Material will penetrate between 0.08 - 0.12 inches (2-3 mm).
Spectrum Z™510 3D Printer Hardware Manual Post-Processing the Part • Label disposal materials. • Wear dust mask when sanding finished parts. • Read the Material Safety Data Sheet for Z-Max prior to the use of this material. Mixing Instructions • When using the 250 gm Z-Max kit simply pour the entire contents of the Z-Max Hardener container into the Z-Max Resin container and mix the two parts thoroughly for two minutes prior to application.
Spectrum Z™510 3D Printer Hardware Manual Post-Processing the Part • When finished, remove the disposable liner and clean sprayer with ethyl alcohol or acetone. • Remove the tip and thoroughly clean by hand to avoid resin buildup. (Cleanup takes approximately 15 minutes). Curing Information • Allow the part to cure for 1 hour at ambient temperature to avoid discoloration prior to placing in the oven for accelerated cure. • The resin can be cured at an accelerated rate in an oven.
Spectrum Z™510 3D Printer Hardware Manual Post-Processing the Part Creating High Finsh Color Parts Painting Powder Management RTV Molding Thermoforming Tough Durable Parts Water Transfer Water Transfer High-Strength Parts www.3dpuser.
Spectrum Z™510 3D Printer Hardware Manual Service Menu and Other Maintenance 8 Service Menu and Other Maintenance The ZPrint Service menu is the primary interface from the desktop when performing routine maintenance on the Spectrum Z™510 3D Printer. 8.1 Unpark Unpark moves the Carriage from its parked position at the Service Station to the opposite side of the Fast Axis to allow easy access for routine cleaning. 8.2 Change Print Heads 1. Determine which print head needs to be changed.
Spectrum Z™510 3D Printer Hardware Manual Service Menu and Other Maintenance 4. Open printer top cover and then open the Carriage cover. 5. Remove the print head(s) you need to change. 6. Take an alcohol swab and clean the pogo pins. www.3dpuser.
Spectrum Z™510 3D Printer Hardware Manual Service Menu and Other Maintenance 7. Re-insert a new print head(s) and press down. Press firmly on both ends of the print head to secure into place. 8. Close the Carriage cover. 9. Using a moist paper towel, wipe the alignment window located on the bottom, left side of the Carriage. Dry off with a dry paper towel and close the printer top cover. 10. Click Done on the Change Print Heads dialog. 11. Select Service > Purge Print Heads.
Spectrum Z™510 3D Printer Hardware Manual Service Menu and Other Maintenance 12. When purging is completed, return to the Service menu and select Auto Alignment. 13. The printer will print out an alignment pattern. The first several layers will be gray-based and then the color alignment pattern is printed. 14. The last part of the color alignment pattern that is printed is a bulls-eye pattern for you to confirm that all print heads are aligned.
Spectrum Z™510 3D Printer Hardware Manual Service Menu and Other Maintenance 8.3 Purge Print Head Always purge a new print head immediately after replacing an expired print head. When you initiate a purge cycle, there are two options to choose from - Purge All Print Heads and Purge New Print Head. Purge All Print Heads will initiate a purge cycle for all print heads regardless of whether they are new or not. Purge New Print Heads will initiate a purge cycle only for the new print heads. 8.
Spectrum Z™510 3D Printer Hardware Manual Service Menu and Other Maintenance While lubrication of the Fast and Slow Axis is very important, it is equally important not to over-grease the bearings when lubricating. Only a very small amount of grease is required to keep these parts working optimally. Using too much grease will create a situation where the grease will leach onto the Fast Axis and buildup on the bumpers located at each end of the Fast Axis.
Spectrum Z™510 3D Printer Hardware Manual Service Menu and Other Maintenance 5. Place the grease gun on the grease fitting on the Carriage and squeeze once. 6. Wipe the excess grease off with a dry paper towel. 7. Move the Carriage back and forth manually to distribute the grease. When finished, close the printer top cover. www.3dpuser.
Spectrum Z™510 3D Printer Hardware Manual 8.8.2 Service Menu and Other Maintenance Slow Axis Lubrication 1. Assemble the grease gun as instructed on its packaging. 2. Select Service > Unpark. 3. Open the printer top cover. 4. Wipe off the slow axis rail with a dry paper towel. 5. Locate the two grease fittings located behind the gantry. Manually move the gantry if you need to gain access to the grease fittings. 6. Engage the grease gun into the fittings and squeeze once. 7.
Spectrum Z™510 3D Printer Hardware Manual Service Menu and Other Maintenance 8. With the printer offline, press the Spread button on the control panel to distribute the grease. 8.8.3 Piston Screws Lubrication 1. Lower both the feed and build pistons all the way down. 2. Open the front cabinet tray. 3. Locate the piston screws and apply grease from top to bottom. 4. Use your finger to distribute the grease evenly over each piston screw. Close the front cabinet tray. www.3dpuser.
Spectrum Z™510 3D Printer Hardware Manual Service Menu and Other Maintenance 5. Raise and lower both the feed and build pistons a couple of times to evenly distribute the grease. Any excess grease should be wiped off with a paper towel. 8.8.4 Cleaning the Fast Axis Rails and Bumpers 1. Select Service > Unpark. After the Carriage is unparked, you can manually move it in order to clean. 2. Place the printer in Offline mode and open the printer top cover. 3.
Spectrum Z™510 3D Printer Hardware Manual Service Menu and Other Maintenance 5. Check that there is no grease buildup on the Carriage as well. Check both sides of the Carriage where the axis rails and the Carriage join. 6. When finished, close the printer top cover and place the printer back Online. 7. Press OK on the Unpark dialog in ZPrint to close the dialog. 8.
Spectrum Z™510 3D Printer Hardware Manual • Service Menu and Other Maintenance Visually inspect the lines where they connect to the Carriage to see if air bubbles are present. Follow the procedure below if you see air in one or more of the binder lines. 1. In ZPrint, select Service > Bleed Air > Start to move the carriage to the front of the printer where you have easy access to the carriage. 2. Open the carriage cover and remove the print heads for each binder line that has air bubbles present. 3.
Spectrum Z™510 3D Printer Hardware Manual Service Menu and Other Maintenance 4. Attach the syringe tubing to the tip of the syringe and ensure the plunger is pushed all the way down. 5. Place the syringe tube fitting over a printhead septum and slowly pull the syringe plunger to draw binder through the tubing and into the syringe. You will see the air bubbles come through the syringe tubing. When there is no air present, the tubing looks solid with binder. www.3dpuser.
Spectrum Z™510 3D Printer Hardware Manual Service Menu and Other Maintenance 6. Have a paper towel ready as you lift the syringe tube fitting off of the septum to prevent binder from dripping onto the print head contacts or into the print head housing. 7. In most cases, you can empty the syringe contents into a waste container, but you should check your company, local, and state regulations to ensure you dispose of the binder in accordance to those guidelines. 8.
Spectrum Z™510 3D Printer Hardware Manual Service Menu and Other Maintenance 9. Close the printer top cover and press Cancel to close the Bleed Air dialog in ZPrint. 8.10 Service Print Heads Service Print Heads will initiate a standard service on the print heads. 8.11 Prime Wash Line Prime Wash Line will remove any air from the wash fluid pumping system. This should be performed upon initial machine setup and any time the wash fluid is allowed to run dry. 8.
Spectrum Z™510 3D Printer Hardware Manual Service Menu and Other Maintenance 6. Put the printer Online. 7. Select Service > Toggle Roller On/Off. 8. Using a moist paper towel, wipe under the gantry making sure to remove all powder residue. Dry the area with a paper towel. Select Toggle Roller On/Off to turn off the roller. 8.
Spectrum Z™510 3D Printer Hardware Manual Service Menu and Other Maintenance 8.16 Print Head Report Print Head Report is a useful tool for identifying how old each print head is. The user should access Print Head Report prior to each print job to determine if there is enough print head life to complete a job or to see if any or all of the print heads require changing. 8.
Spectrum Z™510 3D Printer Hardware Manual Service Menu and Other Maintenance 8.20 Best Practices for Powder Management It is important to use best practices to maintain a clean working environment during the operation of your 3D printers. A small amount of extra care to follow these practices can go a long way to keep your powder in your printer where it is most valuable to you. Good powder management promotes a clean work environment and will keep your printer optimally running so you can be productive.
Spectrum Z™510 3D Printer Hardware Manual 9 Troubleshooting Troubleshooting 9.1 The binder solution is being applied in erratic stripes If the binder appears to be applied in fragmented stripes, check the following: 1. Rinse the squeegee clear of any debris. 2. Make sure binder supply is full. If this does not correct the problem, your print heads may be worn out. Replace the print heads as outlined in Change Print Heads. 9.
Spectrum Z™510 3D Printer Hardware Manual Troubleshooting If the control pad illuminates but nothing happens after that, shut the machine off and turn it back on again. The machine should come online. But if it does not, please contact your authorized Z Corporation Service Provider. 9.5 Parts are unusually weak or crumbly • Is the data file known to be without errors? If the *.stl file is not near perfect you will have problems printing the part.
Spectrum Z™510 3D Printer Hardware Manual Troubleshooting 9.8 Air has Entered into the Wash Fluid Line You will need to use the Prime Wash Fluid feature when there is no wash fluid or air has entered the wash fluid line. This can occur in a few instances such as when first installing the Printer, when running out of wash fluid, or when the connection to the fluid line has been disconnected. Air can be easily detected by looking to see if there are air bubbles in the wash fluid line.
Spectrum Z™510 3D Printer Hardware Manual Troubleshooting 9.9 Communication Errors Between Print Head and Printer In general, clean the pogo pins whenever you replace or remove a printhead. Doing this will greatly reduce errors in communication between the printhead and printer. To clean the pogo pins, follow these instructions: 1. Get an alcohol swab (Toolbox) and remove it from its packaging. Crush the plastic casing to release the alcohol into the swab. 2.
Spectrum Z™510 3D Printer Hardware Manual 3D Printer System Details 10 3D Printer System Details 10.1 System Specifications Warning: Check ratings marked on product BEFORE plugging into a power source. Dedicated power outlet requirements: 110 -120 VAC; 50/60Hz; 6.8A max., or 220 - 240 VAC:50/60Hz; 3.4A max., or 100 VAC; 50/60Hz; 7.8A max. Network Temperature Relative Humidity Weight 3D Printer Z510 Dimensions Ethernet 10/100 base T 68-85° F. (20-30° C) 20-60%, non-condensed 470 lbs.
Spectrum Z™510 3D Printer Hardware Manual 3D Printer System Details 10.2 Symbols Used This is the international symbol for Warning or Caution. It indicates the need to consult your manual for further information. It is located on the rear, lower left side of your printer to call your attention to the fact that only trained personnel should open the 3D Printer rear cover. None of the normal operation procedures described in this manual requires you to remove this cover. 10.
Spectrum Z™510 3D Printer Hardware Manual 3D Printer System Details Material Storage Precautions Review the Material Safety Data Sheets (MSDS) carefully before using any Z Corporation materials. Material Storage Usage Powder Store powder on pallets in a cool, dry, ventilated area away from sources of heat, moisture, and incompatible materials. Keep containers tightly closed. Use of powder in environments with more than 30% relative humidity will affect powder performance.
Spectrum Z™510 3D Printer Hardware Manual Appendix 11 Appendix 11.1 Restoring Network and Firmware Settings Configuration mode is obtained by pressing and holding the ONLINE key on the printer control panel. Configuration mode is indicated when the LCD displays: NETWORK SETTINGS The Configuration menu consists of these 5 choices: NETWORK SETTINGS RESTORE FIRMWARE DIAGNOSTIC MODE SAVE AND EXIT DISCARD AND EXIT Press the < Build UP > or < Build DN > keys to scroll through the Configuration menu.
Spectrum Z™510 3D Printer Hardware Manual Appendix Press the < Feed UP > key to move the cursor to the right. Press the < Feed DN > key to move the cursor to the left. Press the < Build UP > or < Build DN > keys to change the value at the current cursor position. • If the cursor is at the rightmost IP ADDRESS field, and the < Feed UP > key is pressed, the LCD display reads: SUBNET MASK 0. 0. 0. 0. Press the < Feed UP > key to move the cursor to the right.
Spectrum Z™510 3D Printer Hardware Manual Appendix Selecting SAVE AND EXIT displays: SAVE AND EXIT Press the < Feed UP > key to save your changes and terminate the Configuration menu. Selecting DISCARD AND EXIT displays: DISCARD AND EXIT Press the < Feed UP > key to terminate the Configuration menu. Your changes for the current session will not be saved. 11.2 Error Codes PLEASE NOTE: %d is a placeholder for numbers corresponding either to a print head number or a value.
Spectrum Z™510 3D Printer Hardware Manual Numerics 3D Print Setup Dialog, Diagram Of Interior And Exterior Saturation, Drop Feed Piston Command, 47 30 E A Empty The Powder From The Overflow Bin, Error Codes Table, 70 Ethernet Connector, 66 Excess Powder, 22 Air In The Binder Fluid Lines, 62 Air In The Wash Fluid Line, 63 Air Pressure When Depowdering, 36 Alcohol Swabs Part Number, 66 Alignment Pattern, 46 B 61 G C Gantry, CENELEC Class A Warning, 65 Change Print Heads, 53 Check Binder Bottles,
Spectrum Z™510 3D Printer Hardware Manual New Vacuum Attachment Image, R 14 Removing The Finished Part, 34 Removing The Part, 18 Replace Fluid Lines With Distilled Water, 59 Report Capabilities, 58 Restoring Network And Firmware Settings, 68 Rinse Rubber Parking Cap, 23 Rinse Rubber Wiper Blade, 23 Roller, 4 Routine Operations, 20 O Offline Mode, 20 Online Mode, 43 Open Or Hollow Area Of Part, 29 Open Or Import Files, 28 Orient Parts, 28 Other Service Menu Items, 59 Overflow Bin Cover, 3 Overview, 1 S
Spectrum Z™510 3D Printer Hardware Manual Wide Blade Utility Scraper, 32 Wipe Metal Spit Cover, 24 Z z®Cast Description, 12 Z510 3D Printer Image, 7 Z510 Powders, Accessories And Tools, Z510 Toolkit Tools, 12 Z-Bond Application Notes, 39 Z-Bond Curing Information, 39 Z-Bond Safety Precautions, 38 ZD5 Depowder Unit, 10 Z-Max Application Notes, 40 Z-Max Curing Information, 41 Z-Max Mixing Instructions, 40 Z-Max Safety Precautions, 39 Z-Max Spraying Instructions, 40 zp®15e Description, 12 ZPrint Dialog, 58 ZP
