Korenix JetWave 2620 Series Dual IEEE802.11a Wireless Outdoor AP/Bridge User Manual Version 2.1.9, Oct, 2009 www.korenix.
Copyright Copyright © 2009 all rights reserved. No part of this publication may be reproduced, adapted, stored in a retrieval system, translated into any language, or transmitted in any form or by any means without the written permission of the supplier. About This Manual This user manual is intended to guide professional installer to install the R2 Extender and how to build the infrastructure centered on it. It includes procedures to assist you in avoiding unforeseen problems.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. To avoid the possibility of exceeding radio frequency exposure limits, you shall beep a distance of at least 100cm between you and the antenna of the installed equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Warranty Z-Com’s standard hardware warranty is for two (2) year from date of shipment from Z-Com or a Z-Com Distributor. Z-Com warrants that hardware will conform to the current relevant published specifications and will be free from material defects in material and workmanship under normal use and service. IN NO EVENT SHALL Z-COM, INC.
CONTENT Chapter 1 Introduction .............................................................................................................................. 11 Introduction .............................................................................................................................................. 11 Appearance.............................................................................................................................................. 11 Key Features........................
Link Test ................................................................................................................................................... 39 Link Aggregation ...................................................................................................................................... 40 Super Mode ............................................................................................................................................. 41 Wireless Security Settings .............
FIGURE Figure 1 R2 Extender .................................................................................................................................. 11 Figure 2 Telemedicine Wireless Broadband ................................................................................................ 13 Figure 3 Campus Wireless Broadband ....................................................................................................... 14 Figure 4 Bracket Mounting – Step 1 ................................
Figure 36 Wireless Statistics ....................................................................................................................... 48 Figure 37 Connection .................................................................................................................................. 49 Figure 38 Password .................................................................................................................................... 50 Figure 39 Remote Management......................
TABLE Table 1 PIN Definition .................................................................................................................................. 21 Table 2 R2 Extender Factory Default Settings ............................................................................................ 27 Table 3 RSSI-Beep Frequency .................................................................................................................... 39 Table 4 Channels in 5MHz Centre Frequency ..................
Chapter 1 Introduction Introduction The R2 Extender is a high-performance outdoor-deployable wireless bridge that provides wireless connectivity among multiple network locations. The R2 Extender has a built-in 23dBi planar antenna that can deliver up to a 40Km connection. An external antenna may also be used to improve signal quality and improve distance. The R2 Extender allows for link aggregation by combining multiple links into one link with greater transmission rate.
Key Features Provide easy installation and high performance wireless connectivity of up to 40km IP67 waterproof housing endures almost any harsh environments Multiple operating modes including Base station, CPE, PTP and PTMP Support 64/128-bit WEP and 802.
Typical Applications This section describes typical applications of the R2 Extender. Telemedicine Broadband Wireless Application The R2 Extender primary usage is as a relay or bridging technology that may be combined with cost effective solar power solution allowing for telemedicine application in remote and rural environments. The R2 Extender is able to deliver stable and high performance broadband connectivity for typical telemedicine applications in a Line-of-Sight environment.
Education Broadband Wireless Application School in remote area or rural areas can be provided with broadband connectivity via local Internet service providers The relay ability of the R2 Extender allows for multiple hops to be made thus allowing the R2 Extender to reach more remote LOS locations beyond 40Kms or to circumvent natural obstructions like mountains..
Chapter 2 Hardware Installation This chapter describes safety precautions and product information you have to know and check before installing R2 Extender. Preparation before Installation Professional Installation Required 1. Please seek assistance from a professional installer who is well trained in the RF installation and knowledgeable in the local regulations. 2.
Safety Precautions For your safety and proper installation, please read and follow the instructions below: ONLY qualified service personnel should service or disassemble this device; When installing the device, note the followings: - Do NOT use a metal ladder; - Do NOT work on a windy or raining day; - Do NOT install, use or service the device during a thunderstorm, as this may cause a remote risk of electric shock from lightning; - Wear shoes with rubber soles and heels, rubber gloves, long sleeved
Product Package The product package you have received should contain the following items. If any of them are not included or damaged, please contact your local vendor for support.
Waterproof RJ-45 Connector Kit 1. Gland h1 2. Sealing Nut h1 3.
Hardware Installation Assemble the Mounting Bracket 1. Place the main bracket into the seating and use a spanner to fasten the bracket to the R2 Extender with M5×16 screws ľ and M5 washers Ŀ provided in the hardware packets; Figure 4 Bracket Mounting – Step 1 2. Assemble the main bracket by placing articulation pole ĸ to the T-form bracket ķ via a M8×90 ĺ screw through the insertion axe and fix with the M8 washer Ļ , spring washer ļ and M8 nutĽ; Figure 5 Bracket Mounting – Step 2 Pole Mounting 1.
Figure 6 Pole Mounting –Step 1 2. Fasten two M8×80 screws ĺ and washers Ļ through the drill holes and main bracket with a spanner; Figure 7 Pole Mounting – Step 2 3. Adjust the antenna for appropriate tilt / vertical orientation. Figure 8 Pole Mounting – Step 3 Note: The horizontal and vertical beamwidth of R2 default antenna is about 10 degree respectively.
Interface Definition The R2 Extender currently provides two interfaces at the bottom, which are PoE & Data with a black plastic cover and RS-232 with a light gray cover that labed “WARNING! No PoE”. Among which, a black RJ45 waterproof connector will be provided for the PoE + Data interface. Figure 9 Interface Definition RS-232 RS-232, which is labeled COM/RESET, is used for debugging purposes as well as for hard reset of the R2 Extender. Below you may find the pin definition of the RS-232.
Figure 10 Detailed View of RS-232 Port Below are the views of RS-232 cover and RJ-45 port respectively, please note the label covered on and DO strictly follow the instructions to avoid damaging your equipment! Figure 11 Warning Label Warning: Do NOT connect PoE powered Ethernet cable to the RS-232 port; otherwise the port may burnout! If RS-232 cable is used outdoor, please DO add a surge protector to protect the equipment circuit! Strongly recommend to add a lightning arrestor on the RS-232 port to prev
Vent Figure 12 Vent Connect Up Before installing the Ethernet cable with a waterproof RJ-45 connector, it is recommended that the Cat-5 RJ-45 coaxial cable be used for the R2 Extender to power PoE connector. 1. To connect to the hole labeled PoE+Data, open the black cover in advance by using a coin or a slotted screwdriver and then screw in the body of the gland and tighten. Figure 13 Connect Up – Step 1 2.
R2 Extender RJ-45 Port Figure 15 Connect Up – Step 3 4. Screw the sealing on the gland and tighten. Figure 16 Connect Up – Step 4 Grounding The R2 Extender is shipped with a grounding wire. The unit must be properly grounded to protect against power surges. The R2 Extender grounding point can be found on the bottom of the unit. It is supplied with an appropriate grounding lug for attachment to the ODU.
Power On To power up the R2 Extender, follow the steps bellow: 1. Plug a user-supplied Cat-5 Ethernet cable from your wired LAN (or a computer) into the power injector RJ-45 jack (DATA IN); 2. Plug a user-supplied Cat-5 Ethernet cable from the R2 Extender into the power injector RJ-45 jack (P+DATA OUT); 3. Connect the power module to the power injector and plug the AC cord into an AC power receptacle; 4. After being powered on, the device will send out the beep sound lasting about 1.
When install the secondary antenna, please make sure power off the device to prevent unexpected damage.
Chapter 3 Basic Settings Factory Default Settings We’ll elaborate the R2 Extender factory default settings. You can re-acquire these parameters by default. If necessary, please refer to the “Restore Factory Default Settings”.
Wireless Client Isolation Disable Access Control Disable SSH (Secure Shell) Enable SNMP Enable/Disable Enable Read Community Name Public Write Community Name Private IP Address 0.0.0.0 System Requirements Before configuration, please make sure your system meets the following requirements: A computer coupled with 10/ 100 Base-TX adapter; Configure the computer with a static IP address of 192.168.1.x, as the default IP address of R2 Extender is 192.168.1.
How to Login the Web-based Interface The R2 Extender provides you with user-friendly Web-based management tool. Open IE and enter the default IP address (Default: 192.168.1.1) of R2 Extender into the address field. A Security Alert window may popup as below, due to browser’s security trusted sites. You may choose to continue to the login webpage.
Figure 21 Main Page Note: The username and password are case-sensitive, and the password is no more than 19 characters! Basic System Setup For users who use the R2 Extender for the first time, it is recommended that you begin configuration from “Basic” in “System” shown below: Figure 22 Basic Setup Chapter 3 Basic Settings Page 30
Wireless Device Name Specify the device name, which is composed of no more than 15 characters with (0-9), (A-Z), (a-z) or (-). Country/Region For the available radio bands vary from country to country, the working channels used are different. Ethernet Data rate Specify the transmission rate of data. IP Address If you select “Manual”, you have to specify a static IP address, subnet mask, default gateway and DNS server for your local area network which connects to the LAN port of R2 Extender.
Wireless Settings Open “Radio” in “Wireless” as below and select “RF1” or “RF2” to make basic wireless configuration on radio card 1 and 2. Figure 23 Basic Wireless Settings Operating Mode Four operating modes are available on the R2 Extender. In a point to point environment where there are only two radios, Peer-to-Peer is recommended as it works more efficiently. Base Station: The R2 Extender connects directly to the main Ethernet LAN and receives connectivity from other wireless devices.
Base Station ID (SSID) For Base Station mode, it requires SSID for CPU clients to associate with. This wireless network name is shared among all associated devices in your wireless network. Keep it identical on all those devices. Note that the SSID is case-sensitive and can not exceed 32 characters. Wireless Mode The R2 Extender can only communicate with wireless devices of 802.11a. Channel/Frequency Channel varies much as the available band differs from country to country.
higher priority than common one. To enable WMM, the wireless client should support it as well. Super Mode Super mode is an effective way to enhance performance. It can boost the transmission data rate up to 108Mbps. R2 Extender provides you with three kinds of Super mode, which are Fast Frame, Burst and Compression. function as well. To enable Super Mode, the remote R2 Extender should enable the For more information you may refer to Super Mode in Chapter 4 Advance Settings.
Chapter 4 Advanced Settings Advanced Wireless Settings Open “Radio” in “Wireless” and turn to “Advanced Parameters” at the bottom to make advanced wireless settings. Figure 24 Advanced Parameters RTS Threshold The R2 Extender sends RTS (Request to Send) frames to certain receiving station and negotiates the sending of a data frame. After receiving an RTS, that STA responds with a CTS (Clear to Send) frame to acknowledge the right to start transmission. The setting range is 0-2346 in byte.
Distance in Meters To decrease the chances of data retransmission at long distance, R2 Extender can auto adjust proper ACK timeout value by specifying distance of the two nodes. Default distance is 10km. This will be only useful in CSMA mode. TDM Coordination Time Slice Specify the time slice of TDM Coordination. It allows a certain amount of time (in ms) that data will transmit to each other before it moves to the next user. This is a repetitive cycle.
Figure 25 Peer-to-Peer Linksʳfor CSMA Chapter 4 Advanced Settings Page 37
The other way to establish PTMP connectivity is to setup the same group ID under “Radio” in “Wireless”. This feature only available under Peer-to-Peer (TDMA) mode and only devices with the same Group ID can communicate. Figure 26ʳPTP/PTMP for TDMA Note: When establish PTMP network, make sure all the remoteʳwireless devices are withinʳthe antenna beam width. Antenna Alignment Tool Under Peer-to-Peer (CSMA) mode, Antenna Alignment Tool is available.
To use Antenna Alignment Tool, follow the steps bellow: Open “Peer-to-Peer Setup” and select “RF1” or “RF2”. Enter the MAC address of the remote bridge and click on the Apply button. Then click the “Align Antenna” button and the “Antenna Alignment Tool” window will popup. Set the target RSSI (e.g. -70dBm) and click “Start” button. Wait about 5 seconds, the antenna alignment starts and performs alignment every one second.
Figure 28 Link Test Link Aggregation Link Aggregation combines two physical network links into a single logical link for increased bandwidth. With it enabled, users can increase the capacity and availability of the communications channel between devices (both switches and end stations). Besides, link aggregation also provides load balancing.
Full Duplex Two Channels: Normally, the wireless module in R2 Extender receives and transmits wireless packets concurrently; if check this box, it only transmits wireless packets on WLAN but stops receiving. Thus the wireless performance could be enhanced further more. Note: Link aggregation takes effect only when both cards work on peer-to-peer mode! Super Mode Super mode is an effective way to enhance the Wi-Fi performance; it can boost the transmission data rate.
By performing real-time hardware data compression, it increases throughput via using pre-compressed frames with no impact on host processor. Note: Only all the wireless devices share the same wireless connectivity support Super mode, can this function be available! The throughput may vary depending on the actually environment and data traffic flow.
Network Authentication Open: It allows any device to join the network without performing any security check. Shared Key: Data encryption and key are required for wireless authentication before association. (Only available in BS and CPE mode) WPA-PSK: It is a simplified WPA mode with no need for specific authentication server.
Access Control The Access Control appoints the authority to STA on accessing R2 Extender, thus a further security mechanism is provided. This function is available only under Base Station mode. Open “Access Control” in “Wireless” as below, check “Turn Access Control On” to enable this function. Figure 32 Access Control Available CPEs In this table lists the CPEs connecting with R2 Extender currently.
accounting; playing a central role in the network in providing the capabilities of authenticating, authorizing, accounting, auditing, alarming and etc. It allows an organization to maintain user profiles in a central database that all remote servers can share. Open “RADIUS Settings” in “System” to make RADIUS configuration. Figure 33 RADIUS Settings Authentication/Access Control RADIUS Server Login This is for RADIUS authentication.
Chapter 5 Management View R2 Extender Basic Information Open “About” in “System” to check the basic information of R2 Extender, which is read only. Figure 34 Basic Information View Ethernet Statistics Open “Ethernet Status” in “Status” to check the data packets received on and transmitted from the Ethernet port in LAN. Click “Refresh” to view current statistics. All is read only.
Figure 35 Ethernet Statistics View Wireless Statistics Open “Wireless Status” in “Status” to check the data packets received on and transmitted via wireless network. Click “Refresh” to view current statistics. All is read only.
Figure 36 Wireless Statistics Connection Open “Connection” in “Status” to check the information of remote CPEs connected with the R2 Extender, these values also help determine whether the antenna is aligned in an appropriate direction. The table will be updated every 30 seconds. All is read only.
Figure 37 Connection Password From “Change Password” in “Management”, you can change or default the password to manage your R2 Extender.
Figure 38 Password Change Password For security concern, you have to enter the current password first and then enter the new one twice respectively in “New Password” and “Repeat New Password” fields. Restore Default Password If you would like to restore the default password, enter the current password first and then check “Yes” and click “Apply” to default the password.
Figure 39 Remote Management Remote Console The R2 Extender supports CLI management, which could be accessed by Secure Shell (SSH). It is recommended PuTTY be used to login. Download it from http://www.putty.org/ for free. The minimum system requirement for using PuTTY is Windows 95, 98, ME, NT, 2000, XP and Vista on Intel x86. Follow the steps below to implement: Once the program is downloaded, open up by double-clicking ; Note that before using PuTTY, be sure you are able to connect to the R2 Extender.
Figure 40 PuTTY Configuration 1 From “Connection” in the left menu bar, click “SSH”; select “2” as “Preferred SSH protocol version”; make “3DES” the top position in “Encryption cipher selection policy”; Chapter 5 Management Page 52
Figure 41 PuTTY Configuration 2 Click “Open”, a window as below will popup: Figure 42 SSH Enter the user name and password (Default user name/ password: admin/password) respectively, you will see “DEVICE123456>”, which is the name of R2 Extender; Chapter 5 Management Page 53
Enter “help” command to get setting information; alternatively, you can refer to Appendix C. SSH Settings for details. SNMP The R2 Extender supports SNMP management. Set the SNMP parameters and obtain MIB file before remote management. From “Remote Management” in “Management”, set the parameters for SNMP: - Enable SNMP by checking “Enable”; - Specify the “Read Community Name”, “Write Community Name” and “IP Address to Receive Traps” - Hit “Apply” to save settings.
Time Settings Compliant with NTP, the R2 Extender is capable of keeping its time in complete accord with the Internet time. Make configuration in “Basic” from “System”: Figure 44 Time Settings Enter the time server IP address and port respectively in “Time Server” and “Time Server Port” fields; Select your desired time zone from the drop-down list, check “Adjust for Daylight Saving Time” if necessary; Hit “Apply” to save settings.
Upgrade Firmware Open “Upgrade Firmware” in “Management” and follow the steps below to upgrade firmware locally or remotely through R2 Extender’s Web: Figure 45 Upgrade Firmware Chapter 5 Management Page 56
Click “Browse” to select the firmware file. Click “Upload” to load the file into the R2 Extender. Wait a moment, the system will reboot after successfully upgrade. Note: Do NOT cut the power off during upgrade, otherwise the system may crash! Backup/Restore Settings It is strongly recommended to back up configuration information in case of something unexpected. If tragedy hits your device, you may have an access to restore the important files by the backup.
Backup Settings By clicking “Backup” a dialog box will popup. Save it, then the configuration file is saved to your local computer. Retrieve Settings By clicking “Browse” a file selection menu will appear, select the file you want to load, like bridge.cfg; Click “Retrieve” to load the file. After automatically rebooting, new settings are applied.
Event Log Event log is used for recording events occurred on the R2 Extender, including station connection, disconnection, system reboot and etc. Open “Event Log” in “Management” as below. Figure 48 Event Log Enable Log: Enable System log or not; Syslog Server IP Address: Specify the IP address of the server; Syslog Server Port Number: Specify the port number of the server; Hit “Apply” to save settings; Event Log Window: Lists all occurred events in this field.
Reboot You can reboot your device from “Reboot” in “Management” as below: Figure 49 Reboot Check “Yes” and click “Apply” to reboot the R2 Extender. This takes a few minutes, during which the device will send out the buzzing sound, informing you the system is rebooting.
Chapter 6 Troubleshooting This chapter provides troubleshooting procedures for basic problems with the R2 Extender. For warranty assistance, contact your service provider or distributor for the process. Q 1. What if my R2 Extender fails to connect to the remote one? Ethernet Link: Check the availability of power to the bridge by observing the LED status on the power injector or on top of the RJ-45 Jack of the unit. - Green: The R2 Extender is connecting to the backhaul network.
Q 4. What if I can not open the Web-based management interface? Please check the followings: Check whether the power supply is OK; Try to power on the unit again. Check whether the IP address of PC is correct (in the same network segment as the unit); Login the unit via other browser such as Firefox. Hard reset the unit. Q 5. What if the signal quality is poor or not so good? Check whether there is obstacle between units. Obstacle may lead to poor signal. Check the antenna height.
Appendix A. Channel – Frequency Table The R2 Extender can be operated in four different band widths, which are 5MHz, 10MHz, 20MHz and 40MHz. The following tables illustrate the channel with corresponding frequency in each band width. Table 4 Channels in 5MHz Centre Frequency Channel Frequency 149 5.745 GHz 150 5.750 GHz 151 5.755 GHz 152 5.760 GHz 153 5.765 GHz 154 5.770 GHz 155 5.775 GHz 156 5.780 GHz 157 5.785 GHz 158 5.790 GHz 159 5.795 GHz 160 5.800 GHz 161 5.805 GHz 162 5.
Table 6 Channels in 20MHz Centre Frequency Channel Frequency 149 5.745 GHz 153 5.765 GHz 157 5.785 GHz 161 5.805 GHz 165 5.825 GHz Table 7 Channels in 40MHz Centre Frequency Channel Frequency 149 5.745GHz 157 5.785GHz 165 5.825GHz The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user. Appendix A.
Appendix B. Channel – Country List Table The R2 Extender support country selection, there are different channel when select different country. The following tables list the channel with country code in each bandwidth.
Table 9 Country of European Union Country Mode Channel list 40Mhz Belgium 11bg (1-13) Bulgaria *Ukraine Croatia Excluded Cyprus CH12-CH13 6 20Mhz 10Mhz 5Mhz 1/2/3/4/5/6/78 1/2/3/4/5/6/7/8 1/2/3/4/5/6/7/8 /9/10/11/12/13 9/10/11/12/13 9/10/11/12/13 Czech Republic Estonia Finland F.Y.R.O.
Table 10 Other Countries Country Channel list Mode 40Mhz 11bg 6 20Mhz 10Mhz 5Mhz 1/2/3/4/5/6/7/8/9/ 1/2/3/4/5/6/7/8/9/10 1/2/3/4/5/6/7/8 10/11/12/13 /11/12/13 9/10/11/12/13 ʳ 11a 100/108/116/ 100/104/108/112/ 99/101/103/105 99/100/101/102 (5470Д5725) 140 /107/109/111/113 /103/104/105/106 Excluded /115/117/119/133 /107/108/109/110 CH120~CH131 /135/137/139/141 /111/112/113/114 116/136/140 Meteorology /115/116/117/118 Radars /119/133/135/136 /137/138/139/140 /141 ʽIreland Liechte
11bg 6 (1-13) 1/2/3/4/5/6/7/8/9/ 1/2/3/4/5/6/7/8 1/2/3/4/5/6/7/8 10/11/12/13 9/10/11/12/13 9/10/11/12/13 11a 100/108/ 100/104/108/112/ 99/101/103/105 99/100/101/102 (5470Д5725) 116/140 116/136/140 /103/104/105/106 /107/109/111/113 Excluded /115/117/119/133/ /107/108/109/110 CH120~CH131 135/137/139/141 /111/112/113/114 Meteorology /115/116/117/118 Radars /119/133/135/136 /137/138/139/140 UK /141 (5725~5850) 151/167ʳ 147/151/155/167 146/148/150/152 146/147/148/149/ Excluded /1
Appendix C. ASCII WEP can be configured with a 64-bit or 128-bit Shared Key (hexadecimal number or ACSII). As defined, hexadecimal number is represented by 0-9, A-F or a-f; ACSII is represented by 0-9, A-F, a-f or punctuation. Each one consists of two-digit hexadecimal.
Appendix D.
-ipaddr -- radius IP address -port -- radius port number -secret -- radius secret string -secondary -- secondary -ipaddr -- radius IP address -port -- radius port number -secret -- radius secret string -wpa --wireless WPA setting -- wireless WPA re-auth -reauthtime period(in seconds) -- enable wireless WPA -keyupdate global update condition -mode -interval -account -- wireless WPA global key update condition -- wireless WPA global key update interval --account radius setting -primary -
-wirelessmode --wireless mode --wireless channel(depends -channel country and on wireless mode) --wireless -txrate transmission data rate -bandwidth -- wireless bandwidth --use -cpe mode multicli or lan-to-lan -cpedownfloww -- wireless down flow idth width for CPE mode --wireless -OutputPower transmit power --enable TDM mode or -VQoS/TDM not --station’s -tdm timeslice timeslice value -fragmentationt --wireless fragmentation hreshold threshold(even only) --wireless -rtsthresh
-rssi -2 -macaddress -bandwidth -status remote AP --down flow width for pxp mode --remote AP status or active for pxp mode --3rd remote AP for pxp mode -- remote AP --down flow width for pxp mode --remote AP status or active for pxp mode -- remote AP ipaddr -rssi -- remote AP rssi -macaddress -bandwidth -status --4th remote AP for pxp mode -- remote AP mac address for pxp mode --down flow width for pxp mode --remote AP status or active for pxp mode -ipaddr -- remote AP ipaddr -rssi -- rem
-type -- wireless wep key type -1 -- wireless wep key 1 -2 -- wireless wep key 2 -3 -- wireless wep key 3 -4 -- wireless wep key 4 -spaceinmeter --wireless space in meter --wireless remote bssid -remotebssid in cpe mode -- wireless remote ssid in -remotessid cpe mode -network-status --wireless network status -bsscanlist --bs list -signal level -- signal level(dBm) -remoterssi --remote bs and rssi -wmm --wmm settngs -super_audio --Fast_Frame settings -super_video --super burst se
Appendix E. GPL Declamation PUBLIC SOFTWARE DECLAMATION In the software we delivered, there are may contain some public software, if it is, please read below carefully: 1. Definition “Public Software”, when applicable, shall mean that portion of the Licensed Software, in source code form, set forth in the below Table, and provided under the terms set forth in the Section 5, the indicated website, the complete license terms can be found .
The supplier hereby express that the supplier shall have no liability for any costs, loss or damages resulting from Licensee’s breach of the terms and conditions applicable to use, conversion or combination of the licensed software with or into Public Software. 4. NO WARRANTY. This program or licensed software is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY.
1.0.6.tar.gz dropbear Copyright (c) http://matt. GNU GENERAL PUBLIC http://www.gnu.o 2002-2006 Matt ucc.asn.au LICENSE Version 2 rg/licenses/old-li Johnston /dropbear/ censes/gpl-2.0.ht Portions copyright (c) dropbear- ml 2004 0.51.tar.bz Mihnea Stoenescu hostapd 2 Copyright 2002-2006, (c) http://host GNU GENERAL PUBLIC http://www.gnu.o Jouni ap.epitest. LICENSE Version 2 rg/licenses/old-li Malinen fi/releases/ censes/gpl-2.0.ht hostapd-0. ml and 4.
gz linux ftp://ftp.ker GNU GENERAL PUBLIC http://www.gnu.o nel.org/pu LICENSE Version 2 rg/licenses/old-li b/linux/ker censes/gpl-2.0.ht nel/v2.6/lin ml ux-2.6.20.3 .tar.bz2 Appendix E.
