Read Instructions Before Using Your New E-bike D Diirrtt H Haaw wkk 2200 N Naavviiggaattoorr S SM M2266 X Xpplloorreerr X XFF2266 N Naavviiggaattoorr S SFF2266 O Ouuttbbaacckk 2266 X Xpplloorreerr X XM M2266 DO NOT RETURN STORE. For questions regarding assembly and use, call Customer Service: 877-441-6999.
NOTICE! Before using your new E-bike the first time, Charge 6hours for Li-ion batteries and 8 hours for SLA(Sealed Lead Acid) batteries Always recharge the battery before the power indicator shows no power. Failure to follow these instructions voids any warranty, whether stated or implied. Before operating your E-bike Warning! This product does not conform to Federal Motor Vehicles Standards and Is not intended for operation on public streets, roads or highways.
Congratulations on your new purchase! Our service department is dedicated to your satisfaction with 877.441.6999. For questions regarding performance, assembly, operation, parts or return, contact the Manufacturer directly by calling toll free DO NOT RETURN TO STORE 877.441.6999. DO NOT RETURN STORE. For questions regarding assembly and use, call Customer Service: 877-441-6999.
Before You Ride About this Manual It is important for you to understand your new bicycle. By reading this manual before you go out on your first ride, you will know how to get better performance, comfort, and enjoyment from your new bicycle. It is also important that your first ride on your new bicycle is taken in a controlled environment, away from cars, obstacles, and other cyclists. General Warning Bicycles can be hazardous activity even under the best of circumstances.
Safety Checklist Before you ride, it is important to carry out the following safety checks: 1. Brakes Ensure front and rear brakes work properly Ensure brake shoe pads are not over worn and are correctly position in relation o the rims. Ensure brake control cables are lubricated, correctly adjusted and display no obvious wear. Ensure brake control levers are lubricated and tightly secured to the handlebar. 2.
4. Chain Ensure chain is oiled, clean and runs smoothly. Extra care is required in wet or dusty conditions. 5. Bearing Ensure pedals are securely tightened to the cranks. Check headset, wheel bearings, pedals bearing and bottom bracket bearings. 6. Cranks and Pedals Ensure pedals are securely tightened to the cranks Ensure cranks are secure to axle and are not bent. 7. Derailleurs Check that front and rear mechanisms are adjusted and function properly.
9. Accessories Ensure that all reflectors are properly fitted and not obscured. Ensure all other fittings on the bike are properly and securely fastened, and functioning. Ensure the rider is wearing a helmet. 10. Motor Drive Assembly and Throttle Ensure all motor drive components are correctly mounted and functioning properly. 11. Battery Pack Ensure the batteries are in good operation condition and kept fully charged and properly secured and locked. DO NOT RETURN STORE.
Helmets It is strongly advised that a properly fitting, ANSL or SNELL approved, bicycle safety helmet be worn at all times when riding your bicycle. In addition, if you are carrying a passenger on a child safety seat, they must also be wearing a helmet. The correct helmet should: -be comfortable -be lightweight -have good ventilation -fit correctly -cover forehead Always wear a properly fitted helmet which covers the forehead when riding a bicycle. Many states require specific safety devices.
Component List D Diirrtt H Haaw wkk 2200 N Naavviiggaattoorr S SFF2266 DO NOT RETURN STORE. For questions regarding assembly and use, call Customer Service: 877-441-6999.
N Naavviiggaattoorr S SM M2266 O Ouuttbbaacckk 2266 DO NOT RETURN STORE. For questions regarding assembly and use, call Customer Service: 877-441-6999.
X Xpplloorreerr X XFF2266 X Xpplloorreerr X XM M2266 DO NOT RETURN STORE. For questions regarding assembly and use, call Customer Service: 877-441-6999.
Battery Gauge When the throttle or sensor is engaged (Powering the motor) and the bicycle is in motion, the LED’s on the battery gauge (on the throttle or separate unit) indicate instantaneous line voltage as measured at the battery terminals- and not the available energy in the battery pack. The line voltage will fluctuate depending on the instantaneous load that the motor is under.
Throttles Throttle, are equipped on some models of electric bicycles. Throttles operate be rotating the throttle much like a motorcycle. They generally are the inner half of the right side handlebar grip and may also contain a battery gauge. The more you twist the throttle, the faster the motor system will propel bicycle. TAG Throttle TAG (Twist and Go) Before you begin riding, turn the main power switch on, then start riding as you would ride a regular, non-motor assisted bicycle.
Taking Care of Your Batteries Proper maintenance of the batteries will maximize their lifespan and available ride time. ·We use SLA (Sealed Lead Acid) or Li-Ion (Lithium Ion) batteries in all of our electric bicycles. These are very user friendly types of batteries when cared for properly. ·Batteries should be fully charged immediately when they are received for the recommended charger times. FULLY CHARGE BATTERIES BEFORE FIRST USE. Below are the recommended charge times for each type of the batteries.
· The Li-Ion battery rear lights power is directly on the rear of battery . · The Battery power switch is the Red Button under the rear battery (beneath LED Light). ·The Li-Ion battery charger connector is covered by a rubber cover when you lift the battery handle. · The SLA Switch for On/Off is the key, rotate clockwise to turn on the battery power. · SLA charger connector and Fuse on opposite side. DO NOT RETURN STORE. For questions regarding assembly and use, call Customer Service: 877-441-6999.
SLA Battery Packs (Sealed Lead Acid battery) SLA battery packs: 24V 10Ah Sealed Lead Acid Battery, First time charging time: 8 hours, Recharging time: 6~8 hours, Do not charge longer than 24 hours! Last about 350 recharge cycles. 1. Turn the key to unlock the battery box. 2. Lift up Seat via lever, Pull out the battery box along the rail & remove, the battery can now be charged separately. 3. Push the battery box into the compartment along the rail, turn the key to lock the box. DO NOT RETURN STORE.
Li-Ion Battery Packs (Lithium-ion battery) Li-ion battery packs: 36V 10Ah Lithium Battery, First time charging time: 6 hours, Recharging time: 4~6 hours, Do not charge longer than 24 hours! Last over 1000 recharge cycles. 1. Turn the key to unlock the battery box. 2. Pull out the battery box along the rail & remove, the battery can now be charged separately. 3. Push the battery box into the compartment along the rail, turn the key to lock the box . DO NOT RETURN STORE.
Charger The electric bike comes with its own “Smart Charger” that connects with an easy-access charger port for recharging the batteries. This charger has lights which show the battery charge status. Batteries work best when they have a full charge, so always be sure to recharge them fully after each ride. If you leave then in a run-down condition, without recharging them, it will shorten their life expectancy.
How to use the SLA Chargers (Standard) CAUTION CHARGE ONLY LEAD ACID TYPE RECHARGEABLE BATTERY.RISK OF ELECTRIC SHOCK, DRY LOCATION USE ONLY. SEE INSTRUCTION MANUAL FOR USE. 1. Red light means charging 2. Green light means charge-full 3. Input: AC100-240V~, 1.5A (Max) 47/63Hz 4. Output: DC29.2V—2.0A 5. Plug the charger into the outlet. The indicator light on the top of the charger will illuminate when the charger is working properly. Refer to the sticker on the charger for actual status light indication.
How to use the Li-ion battery charger CAUTION RISK OF ELECTRIC SHOCK, DRY LOCATION USE ONLY. SEE INSTRUCTION MANUAL FOR USE. 1. Red light means charging 2. Green light means charge-full 3. Input: AC100-240V~, 1.6A (Max) 50/60Hz 4. Output: 42.00V—2.0A 5. Plug the charger into the outlet and turn the charger “ON” via the switch on the black side. The red power light on the front of the charger will illuminate when the charger is working properly. 6.
Battery Care Battery Storage How to store your battery for a extended time? Charge the battery every 3 months to avoid capacity loss. Batteries slowly self-discharge when left unused for a long time; if battery cells are allowed to reach a critically low voltage, their lifespan and capacity will be permanently reduced. Always disconnect your charger from the wall outlet and battery before storing the battery. Avoid storing your battery in extreme temperatures, whether hot or cold.
recharge be performed at least every 90 days for Li-ion batteries and at 30 days for SLA batteries. Q: Will I get more performance for my bike if I leave the batteries to charge longer? A: No, once the batteries are fully charged ( as indicated by the light on the charger) it is best to unplug them from the charger, leaving the batteries charging longer than necessary is called “overcharging” and will not increase performance. Our bikes supplied chargers are designed to avoid over-charging a battery.
When recycling lead batteries do not mix them with non-lead batteries. Non-lead batteries pose a fire/explosion hazard if brought to a lead battery recycling facility. Lead batteries (example: sealed lead acid batteries, etc.) and non-lead batteries (example: lithium ion, nickel metal hydride, etc.) are recycled at different facilities. Do not dispose of batteries in a fire due to risk of explosion. In the event of disposal, dispose only in accordance with federal, state and local regulations.
Quick release to adjust the height of the seat which is comfortable for you.(Xplorer & Outback Models). The Navigator & Dirt Hawk seat, you can lift the seat and take out of the battery to recharge separately. DO NOT RETURN STORE. For questions regarding assembly and use, call Customer Service: 877-441-6999.
Braking Adjustment V-Brake 1. If fitted with V-brakes, insert the brake body into the center spring hole in the frame mounting boss, and then secure the brake body to the frame with the link fixing bolt. 2. While holding the shoe against the rim, adjust the amount of shoe protrusion by interchanging the position of the B washers (i.e 6mm and 3mm) so that dimension A is kept at 39mm or more. DO NOT RETURN STORE. For questions regarding assembly and use, call Customer Service: 877-441-6999.
3. While holding the shoe against the rim, tighten the shoe fixing nut. 4. Pass the inner cable through the inner cable lead. Set the cable with a clearance of 1mm between each brake pad and the rim, tighten the cable fixing bolt. 5. Adjust the balance with the spring tension adjustment screws DO NOT RETURN STORE. For questions regarding assembly and use, call Customer Service: 877-441-6999.
6. Depress the brake lever about 10 times as far as the grip to check that everything is operating correctly and that the shoe clearance is corrected before riding the bike. Chain Adjustment Inspection The chain must be kept clean, rust free and frequently lubricated in order to extend its life as long as possible. It require replacement if it stretches, breaks,or causes inefficient gear shifting. Make sure that there are no stiff links, they must all move freely.
Adjustment and Replacement On derailleur geared bicycles the rear derailleur automatically tensions the chain. To adjust the chain on single speed freewheel, coaster hub braked or 3 speed hub geared bicycles: 1. Loosen the rear axle nuts ( and coaster brake arm clip ) and move the wheel forward to loosen , or backward to tighten, in the frame. 2. When correctly adjusted, the chain should have approximately 10mm(3/8’’) of vertical movement when checked in the center between the chain wheel and rear sprocket.
Fuse All Yukon Trail electric bicycles are equipped with fuse. The fuse may be located, depending on the model of the bike, in the following locations: SLA fuse (40A glass type fuse) on the battery pack, externally accessible. li-Ion, 30A blade type fuse & 5A blade type fuse- inside the bottom end of the down tube, remove down tube cap to access. In the event of an overload the fuse will pop and need to be replaced. In this instance replace only approved part from Yukon Trail. Risk of fire.
Tools Bag 1. 2pcs Open ended wrench: 8mm/10mm, 13mm/15mm 2. 2pcs Allen key wrenches: 2.5mm/3.5mm/4mm, 5mm/6mm/8mm 3. 1pc Standard flat head screwdriver DO NOT RETURN STORE. For questions regarding assembly and use, call Customer Service: 877-441-6999.
Troubleshooting Failure symptoms The battery indicator light on the meter is off, and the motor does not work Cause of Problem Battery voltage is too low Solution Immediately charge Battery is not providing Replace the battery proper power The battery lock does not Replace of the battery work, preventing battery lock from being properly secured Motor is operating when battery lock is unlocked The motor stops intermittently Reduced Ride Time Battery is not fully charging Headlights doesn’t work Contr
(Diagram is for representational purpose only. Your bicycles’ wiring system may differ) WARRANTY REGISTRATION DO NOT RETURN STORE. For questions regarding assembly and use, call Customer Service: 877-441-6999.
RETURN THE PRODUCT REGISTRATION WITH A COPY OF YOUR SALES RECEIPT TO : Yukon Trail, Inc.