Mobile Travel Router EE1 Quick Start Guide www.yoyomotion.
Operating Modes YOYORouter EE1 has four operating modes to keep you connected via cabled Ethernet WAN (Wide Area Network), Wireless WAN (Mobile Broadband) or Wi-Fi hotspot sharing: Wireless WAN (Mobile Broadband) Mode Make a Mobile Broadband connection using LTE/HSPA/HSDPA /UMTS/EDGE/GPRS via a USB modem (USB dongle) plugged in to YOYORouter EE1. Share it via Wi-Fi and Ethernet.
Preparing YOYORouter EE1 1. Open the battery compartment • Slide the cover in the direction shown until it clicks open. • Lift the cover away from YOYORouter. 2. Insert the battery • WARNING: Always be sure to disconnect the power before inserting or removing the battery. • Hold the battery so that the three gold contacts align with the three gold pins in the compartment. • Insert the battery so that the contacts meet. • Press the other end of the battery in to the compartment so that it clips in to place.
Connecting to YOYORouter EE1 Select YOYORouter’s Wi-Fi network which has a network name (SSID) like YOYORouter-07-76. The network name and network password are printed on a label in the battery compartment and on the box. For example, in Windows 7 • Click the icon in the notification area. • Select your YOYORouter’s network. • Click Connect and enter the Wi-Fi password when prompted. If you are using a Mac • Click the network icon • Select your YOYORouter’s network.
Setting up YOYORouter EE1 in Wireless WAN Mode Note: A full list of supported USB modems is available from the Supported Cards List link in the status page, or from www.yoyomotion.com. 1. Make sure your SIM card is installed in the USB modem. Consult the USB Modem’s documentation for further information. 2. Plug in your USB Modem and turn on YOYORouter EE1. Allow at least 60 seconds for the USB modem to be detected and configured.
Setting up YOYORouter EE1 in Ethernet WAN Mode 1. Plug in the Ethernet cable and switch on YOYORouter EE1. Typical WAN sources include ADSL modems, cable modems and hotel/office cabled Internet connections. 2. 3. • • • Connect to YOYORouter via Wi-Fi, access the status page at http://192.168.1.1 and log in. Select Wizard and step through the Setup wizard. At the step Select WAN Type Select WAN Interface type Ethernet WAN. Select the required WAN Type.
Setting up YOYORouter EE1 in Ethernet WAN Mode with Failover First configure YOYORouter EE1 in Wireless WAN Mode and test the connection. Next, configure YOYORouter EE1 in Cable and test the connection. To enable WAN Mode with Failover, ensure that the USB Modem and Ethernet WAN are both connected and follow these steps: 1. Log in. 2. Select Advanced then Network Setup. 3. Against Activate WWAN for Auto-Failover • Check Enable.
Setting up YOYORouter EE1 in Share Mode 1. 2. 3. 4. • • Switch on YOYORouter EE1. Connect to YOYORouter via Wi-Fi or Ethernet, access the status page at http://192.168.1.1 and log in. Select Wizard. Click through the Wizard making any changes to the default settings if necessary. When you get to Select WAN Type in the Wizard Select WAN Interface to be Wireless WAN. Select WAN Type: Wi-Fi HotSpot and click Next> YOYORouter scans for available Wi-Fi networks and presents a list; select the required network.
Wi-Fi Configuration Tips YOYORouter is pre-configured with a default Wi-Fi network name (SSID) and password. The network name and password are printed on the label on the underside of the device and on the label affixed to the carton in which it was packaged. Security is set to WPA-PSK(TKIP) and WPA2-PSK(AES) – devices may connect using either of these. In the Configuration Wizard you can: • Change the Network ID (SSID) to a name of your own choice. • Manually select a frequency channel.
Important Information Please read this information before using your YOYORouter. REMEMBER THAT YOYOROUTER CONTAINS A WI-FI TRANSMITTER AND AN ATTACHED USB MODEM CONTAINS A MOBILE PHONE TRANSMITTER. YOU MUST AT ALL TIMES OBEY ALL RESTRICTIONS FOR BOTH OF THESE TRANSMITTER TYPES. Safety and Usage Guidelines • You must read and follow the guidelines for your USB Modem • When inserting or removing the SIM card, do not touch the gold connectors.
