FCC ID : O44JR200AMEN This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. CAUTION : Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this device. USER’S GUIDE By Youngshin Electronics Co., Ltd. www.
User’s GUIDE User’s GUIDE TABLE OF CONTENTS Page 4 Page 4 Page 5 Page 5 Page 6 Page 6 Page 7 Page 7 Page 7 Page 8 Page 8 Page 8 Page 8 Page 8 Page 8 Page 8 Safety Information Remote : R200 Remote Button Functions Remote Learning Routine Keyless Entry Alarm Mode Trunk Release Panic Mode Valet Mode Optional Programmable Features Ignition Lock Passive Locking Optional Installation Features Door pulse Duration Flashing Signal Light Anti-jacking Page 3
Safety Information Remote Button Functions Please take these safety precautions into consideration, under the following conditions : Button Press Function 1. Servicing the vehicle When servicing your automobile (i.e. changing the oil, washing your car), the Magicar system should be in Valet Mode. 1 0.5 sec Lock 2 0.5 sec Unlock 2. Loaning your vehicle to others Whenever you loan your vehicle to an individual who is not familiar with Magicar, please put the vehicle in Valet mode.
Step2 : Within a 7 second period after cycling the ignition for the 3rd time, Press the button for a 0.5 second. The parking lights will flash once to confirm that the transmitter has been programmed. You can continue programming additional remotes. The parking lights will flash two times when the programming mode has expired. Keyless Entry To lock the vehicle, pressing the button for a 0.5 second. To unlock the vehicle, press the button for a 0.5 second.
OPTIONAL PROGRAMMABLE FEATURES These additional features may be programmed to the Magicar system by your authorized Magicar dealer. Ignition Lock This programmable option enables your vehicle to automatically lock the doors once the key is in the ignition for 30 Seconds.(Also you can lock the doors, If you step on the brake pedal within 30 Seconds) In addition, the vehicle will automatically unlock the doors when the key is pulled out of the ignition.
Installation Tips & Recommendations 1-1. Please be careful not to lock yourself out. Please lower the glass windows before you start the installation in case the door locks with the key inside. Also, learn the remote to the brain module after the installation has been completed. 1-2. Use Digital Multimeter for testing Use a Digital Multimeter for all testing of wires in the vehicle. This should be done on all wires even if you feel that you know exactly what they are and how they should test.
C0N1 C0N2 No 1 (Red) : (+)12V Input Solder this wire to the vehicle’s 12V constant. This wire must be supplied power all of the time and must be able to withstand high current draw. No 2 (Green/ White) : (+)Output for parking Light Positive parking light output. No 3 (Brown) : (+)12V Siren Output The Black wire at the siren is to be chassis grounded. The siren volume can be reduced by cutting the volume wire attached to the siren.
Method 3 : External Actuator No 3 (Red/Black) : Negative Trigger Door Open Sense No 4 (Red) : Positive Trigger Door Open Sense Dome Light Dome Light Door Trigger SW Door Trigger SW +12V < External Actuator> +12V CON3-3(-) Door Trigger CON3-4(+) Door Trigger Please make sure you have found a correct door sensing wire that monitors all doors. C0N3 No 5 (Violet / Black ) : (-)Trunk Trigger Input.
No7 (Black /White) : (-) Input for optional Sensor Options Mode When installing additional sensors, use this wire as the input wire for those sensors. Always remember, when attaching more than one sensor to any input, you must diode isolate them so that they don’t backfeed into each other. Press buttons Option Mode. } LED Ass’y C0N 5 No 1 (Black) : GND (Factory Default) Door Lock/Unlock Pulse Duration 0.
How to set Options Canceling (Going to factory default) Option Mode You can only program one option at a time. You will have to repeat the procedure for every option you would like to change. Step1: Press buttons + for 2 seconds. The siren and signal lights will chirp and flash one time each. - If you fail to program, the siren and signal lights will chirp and flash three times each. Step2: Press button the number of times to go to the option number you want to change.
