Kit £: Recommended with: Bulldog Valve Robot Kit B: Recommended with: Motorized Valve {2-wire}) YORKSHIRE Xx | Valve Controller Installation & User Guide {for Kit Akita BK C} Rev 1.
Helios! Eric with Yo link, here. | want to thank you for your purchase and for placing your trust in Yo link for your smart home needs. Before | worked here, | was a customer! | found the products and customer service to be top-notch. Today, | am responsible for many of the things that enhance your experience with Yo link products and services, including the manuals and videos.
Contents EoTEZOTMOO® RE In the Box = Introduction Using the Yo Link App + Yo link Control-DD Maintenance Specifications Troubleshooting Warning Custom Er Service & Warranty «rowers moan saneness 75 WORD WW OD nh Revised: 02/10/2022 Copyright © 2022 Yo Smart Inc.
Box 2 {Optional Accessory) Type A A. Gas/Water Valve Manipulator B. Bracket (2) {with 2 mounting bolts} Type B A. Gas/Water Valve Manipulator B. Bracket {with threaded hole} C. Bracket {without threaded hole} 0. Stainless Steel Hose Clamp E.
A-2. Kit B YS5001-UC X3 Valve Controller & Motorized Valve Box A. A. Valve Controller 8. Quick Start Guide Box 2 {Optional Accessory) A.
A-3, Kit C-YS55001-UCX3 Valve Controller & Bulldog Valve Robot Box A. A. Gas/Water Valve Controller B. Quick Start Guide Box 2 {Optional Accessory) A. Bulldog Valve Robot B.
B. Introduction The Yo link X3 Valve Controller is a smart device that can control a 12 VDC ball-type {only} gas or water valve manipulator remotely with the Yo link app on your smartphone or tablet or using the SET button on the device. Pressing "Open" or "Close" on the app will mechanically rotate the handle 90 degrees in the appropriate direction, to close or open the valve. — Mounting Holes Secure the controller to the wall, using these two holes.
The LED light indicates the current status of the X3 Valve Controller: IRB mca : Blinking Red Once, Then Green Once Device turned on Blinking Red And Green Alternately Restoring to Factory Defaults Blinking Green Once Turn on the manipulatorfvalve Blinking Green Connecting to Cloud Slow Blinking Green Updating Fast Blinking Green Establishing Connection with Yo link System {Yo link Control} Blinking Red Once Turn off the manipulator/valve or device is connected to the cloud and is functioning normally Fast
Setup C-1. Set Up First-Time Yo link Users (Existing users proceed to €-2. Add Device, next page) & Download the Yo link app through Apple App Store ase Se La Google Play Store (Searching the store or use the QR code on the right} € Theologian Bobolink o 1 Make sure your Hub is connected always onl Con Oil Network Lae N = € Either the Yo link Hub or taco . Speaker Hub is required to 0 Ee reacquired Power | Information. Your hub should be setup i, "| adapter. .
C-2. Add Device €F Tap “ 01” icon, then scan QR Code on the device. Follow the steps to add the device @ Press the SET button once to turn on the device after installation.
D. Installation D-1. Install with Ball-type Manipulator (Type 4) Rocker Arm and — Handle-supporting Bolt Output Shaft of Manipulator —, Clutch Hold the ring and keep pulling down on the clutch, you can rotate the handle manually to open or close the valve 1.
1. These Tools may be Required Phillips Screwdriver Allen Wrench Number 5 Metric 1.
€} Loosen the two screws on the two €} Loosen the brackets into two handle-supporting bolts separate parts (carefully place the two bolts aside) 11
3.
€} Insert the screw through the top of the brackets and the mounting ear of the manipulator with the non-threaded hole (place the two handle-supporting bolts on either side of the handle) 1.
€} Securely tighten the two screws on the two handier-supporiing bolls using a Phillips screwdriver — Handle Rubber Sleeve 1 The handle's rubber sleeve may affect 2.
€ We suggest not permanently installing the X3 Valve Controller until both the controller and the valve manipulator have been tested and they work properly @ Connect the manipulatorcabletotheX3 Valve Controller Cable @ After the connection, proceed to page 46, for testing 15
D-2: Install with Ball-type Manipulator (Type BJ Rocker Arm and “ Handle-supporting Bolt AN X3 Valve Controller Output Shaft of Manipulator —, Clutch Hold the ring and keep pulling down on the clutch, you can rotate the handle manually to open or close the valve Gas/ Water Valve Manipulator {Ball-type} 1 The handle must rotate afl Connection Cable be fully opened or closed cause the wrong valve positioned indicated in Handle ich fT 7 Shaft of Ball Valve manually return the valve / ° Lads Water Pipe the app
1. These Tools may be Required Slotted Screwdriver Phillips Screwdriver Allen wrench Number & metric 1.
€} Loosen the two screws on the two €} Loosen the stainless steel hose handle-supporting bolts clamp using a slotted screwdriver, insert the hose clamp through the slots in the brackets {positioning the screw mechanism on the easiest side to reach for tightening) inch { on the valve body rather ] Adjustable diameter: | than on the pipe, f possible} 3. Begin Installation 1.
€F Install the bracket to the valve €} Insert the screw through the operator through the slot on bracket with the larger, the bottom (The bent tabs non-threaded hole and secure should be facing outward) the screw into the threaded hole in the second bracket c. D.
€} Place the valve operator en the water pipe valve so that the hoseclampisaroundthe base of the ball valve on the opposite side from the lever €} Secure the hoseclampscrew using a slotted screwdriver until the valve operator will juststayvinplace 20
£3 Keep pulling down the clutch, rotate the valve operator so that the two handle-supporting bolts are on either side of the valve handle. Close these handicapping bolts so that they held the valve handle between them.
3 Wesuggestnotpermanentlyinstalling the X3 Valve Controller until both the controller and the valve manipulator have been tested and they work properly €} Connect the manipulator cable tithe X3 Valve Controller Cable €} After the connection, proceed to page 46, for testing 22
D-3: Install with Ball-type Motorized Valve (2-Wire) X3 Valve Controller a Position Indicator Indicator visually shows the valve position Horizontal with the pipe = Open vertical with the pipe = Closed Connection Cable il —— Motorized Valve Ll ,— Water Pipe 23
1.
2. Important |] ® These instructions cover installing the motorized valve on copper pipe, using threaded fittings.
3.
4.
€h Wesuggestnotpermanently installing the X2 Valve Controller until both the contraindicate valve have been tested and they work properly.
D-4: Install the Bulldog Valve Robot | — Clutch Pin Push and hold the clutch pin and use the valve handle {recommended} or Robt handle to open or close the valve a Handle and a a EL Position Indicator be fully opened or closed Rocker Arm and PLE sg ee Handle-supporting ; “ valve will cause the wrong valve position Bolt ~ robe indicated in the app. To prevent this, Output Shaft Bulldog Mounting Ear Bulldog Valve Robot (Ball-type) ,— “ Brackets & [ X38 Valve ~ 5 Controller Shaft of Ball ] Valve \ Handle ‘ Wat
1. Tools Required Phillips Screwdriver 2.
® Place the upper bracket and lower bracket on ® Position the bracket so that the the valve, as shown, and loosely tighten the absolutist aligned with the valve screws pivot point bid — Tab Slot { ; Pivot Point Please note correct —— orientation of bracket NOTE: if your larger bracket has two screw openings, only one screw is required, but both screws can be installed if it still allows for proper placement and adjustment of the Bulldog {install the Bulldog using one screw at first, and add the second screw
® Keepingthecenteraxisofthe Valve Robot'sshaftaligned withe ball valve shaft {as indicated by the red dashed line}, reinsert and tighten the tab slot screw ® Securelytghtenthe two screws on the bracket.
e Remove the nuts and collars from the two handle supporting bolts as shown ® Place the absinthe slot on the rocker arm, with one on each side of the valve handle, as shown ® Putthecollarsbackonthebolts ® Next, while holding the bolts and collar pieces in place, attach the bottom supporting bracket as shown.
€} Connect the Bulldog Valve Robot to the Controller We suggest not permanently installing the X3 Valve Controller until both the controller and the valve manipulator have been tested and they work properly Connect the Bulldog Valve Robot cable to the X3 Valve Controller cable After the connection, proceed to page 46, for testing 35
D-5. Instructions for installing the X3 Valve Controller for use with an existing Valve Manipulator (Non-smart, 12VDC only) 1. These Tools may be Required Wire Cutter/Stripper Utility Knife Scissors Wire Nuts Electrical Tape /Connectors {2} 1. Yourexistingmanipulator must be 2-wire, 12 VDC non-smart, and functional Li] 2 Wire nuts [twist-on connectors) are the recommended wire splicing method.
