Technical Guide

ManualsBrandsYork ManualsVentilatorYork MAXA-MI$ER ERV

MAXA-MI$ER

TECHNICAL GUIDE

V* Series

Unitized Energy Recovery

Ventilators

ERV Unit with 3 - 12.5 Ton Packaged Unit

ERV Unit with 15 - 25 Ton Packaged Unit

ERV Unit with 25 -40 Packaged Unit

ETL Certified per UL 1995 and CSA 22.2

903106-UTG-A-0912

FOR DISTRIBUTION USE ONLY - NOT TO BE USED AT POINT OF RETAIL SALE

Energy recovery COMPONENT rated in

accordance with AHRI/ANSI Standard

1060-2005 and certified to AHRI. Actual

performance in packaged equipment

may vary.

DESCRIPTION

• Reduces cooling load at design temperatures up to 4 tons per

1000 cfm of outside air.

• Reduces heating load up to 2.5 Tons Btuh per 1000 CFM of out-

side air.

• Dry energy transfer. Moisture in supply (intake) air stream is

transferred to exhaust air stream in a vapor state, eliminating

condensate plumbing from the UERV.

• Attaches directly to the UPG rooftop units. All mounting equip-

ment is provided.

• Separate fused power supply. (Except VR74 or VR122)

• Filters / mist eliminators are provided on the entering air open-

ings.

• Adjustable support legs are provided. (Except for Stand Alone)

• Two modes of operation (Pivoting Wheel Models only)

• Recovery mode during normal energy recovery operation.

• True economizer mode when outside sensor calls for

economizer operation (3 - 12.5 ton packaged units

equipped with economizers). U. S. Patent 5,548,970.

• Pivoting wheel models used with packaged unit with econo-

mizer. Sequence of operation controlled by economizer control-

ler. (3- 12.5 Ton Only)

• Balancing dampers provided on VR Modules. (Except VR74

and VR122)

• Centrifugal blowers (both intake and exhaust for high static

capability and low sound levels). (Except VR74 and VR122)

• Heavy gauge galvanized steel cabinets corrosion protected with

powder paint process that match UPG units.

• Fully insulated cabinet.

• AHRI certified internal enthalpy wheel is provided.

• Internal enthalpy wheel made of polymeric material with silica

gel impregnated into the material. The enthalpy wheel has a

five year limited warranty.

• Internal enthalpy wheels are easily cleanable. Large wheels (25

inch diameter and above) are split into easily removable pie

segments. Smaller wheels can be removed from the ERV.

• Continuous operation down to 10 ºF (-12 ºC) without defrost at

indoor relative humidity up to 40%. For temperatures below 10

ºF (-12 ºC), Optional Low Ambient Control Kit is required. Kit

includes temperature sensor to control the ERV before frost

build up can occur on recovery wheel.

Note: MAXA-MI$ER

UERV’s are designed for use with

rooftops using 14” high or greater roof curbs.

Note: ZF/ZH/ZJ/XP 037 thru 150 or ZS/ZU/ZW/XA-A3

thru -12, with ERV must use “slab” type econo-

mizers and downflow position.

Summary of content (48 pages)

PAGE 1
903106-UTG-A-0912 MAXA-MI$ER® TECHNICAL GUIDE V* Series Unitized Energy Recovery Ventilators ERV Unit with 3 - 12.5 Ton Packaged Unit DESCRIPTION • Reduces cooling load at design temperatures up to 4 tons per 1000 cfm of outside air. • Reduces heating load up to 2.5 Tons Btuh per 1000 CFM of outside air. • Dry energy transfer. Moisture in supply (intake) air stream is transferred to exhaust air stream in a vapor state, eliminating condensate plumbing from the UERV.
PAGE 2
903106-UTG-A-0912 TABLE OF CONTENTS DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . 2 UPG UERV MODEL NOMENCLATURE . . . . . . . . . . . . 3 APPLICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 PRINCIPLE OF OPERATION . . . . . . . . . . . . . . . . . . . . . 4 AHRI/ANSI STANDARD 1060-2005 FOR AIR-TO-AIR ENERGY RECOVERY VENTILATION EQUIPMENT . . . . . 4 ENERGY RECOVERY WHEEL . . . . . . .
PAGE 3
903106-UTG-A-0912 LIST OF TABLES (CONT.) Tbl. # 32 AIRFLOW PERFORMANCE - DOWNFLOW CONFIGURATION FOR D080 & D120 . . . . . . . . . . . . . . . . . . . . 35 Pg. # 26 SPECIFICATIONS AND ELECTRICAL DATA - 3000 THROUGH 4600 CFM ERV'S . . . . . . . . . . . . . . . . . . . 28 27 SPECIFICATIONS AND ELECTRICAL DATA - 4600 THROUGH 6200 CFM ERV'S . . . . . . . . . . . . . . . . . . . 29 28 SPECIFICATIONS AND ELECTRICAL DATA - 6000 THROUGH 13000 CFM ERV'S . . . . . . . . . . . . . . . . . .
PAGE 4
903106-UTG-A-0912 APPLICATIONS Critical Terms for Standard 1060 are as follows: Unitized Energy Recovery Ventilators (UERV) are used with the UPG rooftop packaged units. The internal wheel provides sensible and latent energy exchange between the entering and exhaust air streams of a building. This allows a substantial amount of the energy, which is normally lost in the exhaust air stream to be returned into the entering air.
PAGE 5
903106-UTG-A-0912 CROSS LEAKAGE IN UERV’S (PURGE SECTORS) The issue of cross leakage in rotary wheel based UERV's used in space conditioning applications is often misunderstood. As a result, many systems are installed with purge sectors and the additional fan capacity required to allow these sectors to function when in fact they are unnecessary.
PAGE 6
903106-UTG-A-0912 OPTIONAL ACCESSORIES - FACTORY INSTALLED L6 - LAK, SSJ, and PS L7 - LAK and PS L8 - LAK, MOA, and PS Low Ambient Control Kit - Prevents frost formation on energy wheel heat transfer surfaces by terminating the intake blower operation when discharge air temperature falls below a field selectable temperature setting. Intake blower operation resumes operation after temperature rises above the adjustable temperature differential.
PAGE 7
903106-UTG-A-0912 TABLE 2: PERFORMANCE - 3 THROUGH 12 1/2 TON UNITS “R” Series Stationary Wheel for Units without Economizers UPG Unit Size Packaged Unit (Tons) Model No.
PAGE 8
903106-UTG-A-0912 TABLE 3: PERFORMANCE - 15 THROUGH 25 TON UNITS Use this table to determine ventilation and size requirements. Table shows UPG packaged units and matching ERV model, Air Flow Range, and AHRI rated Net Effectiveness at 100% of rated CFM. “R” Series Stationary Wheel for Units without Economizers Nominal AHRI Data (Total UPG Unit ERV CFM Matching ERV Voltage & Voltage Packaged Unit Size Net Effectiveness Range Model Phase Code CFM Model No.
PAGE 9
03106-UTG-A-0912 TABLE 4: PERFORMANCE - PIVOTING WHEEL MODELS “P” Series Pivoting Wheel for Units with Economizers UPG Packaged Unit Model No. ZF036-072 ZR036-060 XP036-060 ZS-03-A6 ZK-03-05 XA-03-05 (42”) ZH037-090 ZF078-090 ZJ037-061 ZR037-090 XP078-090 ZU-A3-07 ZS-06-07 ZW-A3-A5 ZK-A3-07 XA-06-07 Unit Size (Tons) 3-6 ERV CFM Range 6001000 6001000 Max. CFM Power Exhaust 1900 1900 Matching ERV Model VP011A06H VP011B12H 3 - 7.
PAGE 10
903106-UTG-A-0912 Enthalpy Wheel Fresh Air Damper Pivoted out of Intake and Discharge Air Stream (opens during economizer operation) Outside Air Blower (energized) Exhaust Air Blower (energized) Enthalpy Wheel (with removable pie segments) Exhaust Air Blower Unit & UERV Disconnect (provided correct wire size used for both units and local code approval) FIGURE 3 - “P” SERIES PIVOTING WHEEL FOR UNITS W/ECONOMIZERS 10 Unitary Products Group
PAGE 11
903106-UTG-A-0912 TABLE 5: SPECIFICATIONS AND ELECTRICAL DATA - 300 THROUGH 550 CFM ERV’S Model Numbers Line Voltage - 60hz Motor - hp / type Wheel Size (dia x width) - in Motor Speed - rpm Fresh Air Motor Speed(s) Blower Bearing Type Full Load Amps Service Factor Motor - hp Wheel Size (dia x width) - in Motor Speed - rpm Exhaust Air Motor Speed(s) Blower Bearing Type Full Load Amps-Stationary Service Factor Potential Volts Wheel Electrical Motor Speed (RPM)/Wheel (RPM) Data Full Load Amps MCA Total Electr
PAGE 12
903106-UTG-A-0912 TABLE 6: SPECIFICATIONS AND ELECTRICAL DATA - 600 THROUGH 1700 CFM ERV’S VR011 - Rooftop Stationary VP011 - Rooftop Pivoting Model Numbers Line Voltage - 60hz Motor - hp / type Wheel Size (dia x width) - in Motor Speed - rpm Fresh Air Motor Speed(s) Blower Bearing Type Full Load Amps Service Factor Motor - hp Stationary Motor - hp Pivoting Wheel Size (dia x width) - in Exhaust Motor Speed - rpm Air Motor Speed(s) Blower Bearing Type Full Load Amps-Stationary Full Load Amps-Pivoting Servi
PAGE 13
903106-UTG-A-0912 TABLE 7: SPECIFICATIONS AND ELECTRICAL DATA - 1500 THROUGH 2800 CFM ERV’S * VR028 - Rooftop Stationary * VP028 - Rooftop Pivoting Model Numbers Line Voltage - 60hz 208/230v-3ph Motor - hp / type Wheel Size (dia x width) - in Motor Speed - rpm Motor Speed(s) Bearing Type Full Load Amps Service Factor Motor - hp Stationary Motor - hp Pivoting Wheel Size (dia x width) - in Motor Speed - rpm Motor Speed(s) Bearing Type Full Load Amps-Stationary Full Load Amps-Pivoting Service Factor Motor -
PAGE 14
903106-UTG-A-0912 TABLE 8: SPECIFICATIONS AND ELECTRICAL DATA - 2800 THROUGH 3600 CFM ERV’S Model Numbers Line Voltage - 60hz Fresh Air Blower Exhaust Air Blower Wheel Electrical Data Total Electrical Wheel Data VR036 - Rooftop Stationary 208/230v-3ph Motor - hp / type Wheel Size (dia x width) - in Motor Speed - rpm Motor Speed(s) Bearing Type Full Load Amps Service Factor Motor - hp Stationary Wheel Size (dia x width) - in Motor Speed - rpm Motor Speed(s) Bearing Type Full Load Amps-Stationary Servic
PAGE 15
903106-UTG-A-0912 TABLE 9: SPECIFICATIONS AND ELECTRICAL DATA - 3400 THROUGH 5600 CFM ERV’S Model Numbers Line Voltage - 60hz Motor - hp / type Wheel Size (dia x width) - in Motor Speed - rpm Motor Speed(s) Bearing Type Full Load Amps Service Factor Motor - hp Stationary Wheel Size (dia x width) - in Motor Speed - rpm Motor Speed(s) Bearing Type Full Load Amps-Stationary Service Factor Motor - hp (1 phase) Potential Volts Motor Speed (RPM)/Wheel (RPM) Full Load Amps MCA - Stationary OCPD - Stationary Wheel
PAGE 16
903106-UTG-A-0912 TABLE 10: SPECIFICATIONS AND ELECTRICAL DATA - 5500 THROUGH 6200 CFM ERV’S Model Numbers Line Voltage - 60hz Fresh Air Blower Exhaust Air Blower Wheel Electrical Data Total Electrical Wheel Data Motor - hp / type Wheel Size (dia x width) - in Motor Speed - rpm Motor Speed(s) Bearing Type Full Load Amps Service Factor Motor - hp Stationary Wheel Size (dia x width) - in Motor Speed - rpm Motor Speed(s) Bearing Type Full Load Amps-Stationary Service Factor Motor - hp (1 phase) Potential
PAGE 17
903106-UTG-A-0912 TABLE 11: SPECIFICATIONS AND ELECTRICAL DATA - 6000 THROUGH 13000 CFM UERV’S UERV Series Line Voltage - 60hz Motor - hp Wheel Size (dia x width) - in Motor Speed - rpm Exhaust Air Motor Speed(s) Blower Bearing Type Full Load Amps OCPD Service Factor Motor - hp (3 phase) Motor Speed (RPM)/Wheel Wheel Electrical (RPM) Data Full Load Amps OCPD MCA Total Electrical OCPD Wheel Depth x Diameter - in Wheel Data Construction / Media Type Nominal Airflow CFM EATR - -1.00 H2O Enthalpy EATR - 0.
PAGE 18
903106-UTG-A-0912 Models ZF036-072 ZR036-060 XP036-060 ZS-03-A6 ZK-03-05 XA-03-05 A C D B Intake Air Blower 14" High Curbs Required - -1RC0434 Enthalpy Wheel ERV Model Unit Size VR006A06H 036-072 -03 -A6 A 24.75 (629) B 24.63 (624) C 37.9 6 (964) D 8 (203) CFM VR011A06H 036-072 -03 -A6 32.13 (816) 33.5 (851) 48.75 (1238) 8 (203) 600-1000 VP011A06H 036-072 -03 -A6 32.13 (816) 33.5 (851) 48.
PAGE 19
903106-UTG-A-0912 Models ZF180, 210, 240, 300 ZR180, 240, 300 ZJ180, 210, 240, 300 XP180, 240 ZS-15, -18, -20, -25 ZK-15, -20, -25 ZW-15, -18, -20, -25 XA-15, -20 Outdoor Air Intake Blower Enthalpy Wheel A C B 14" Roofcurbs Required on "VR028" - 1RC0436 - 437 24" High Curbs Required on "VR036" - 1RC0477 or 1RC0478 24" High Curbs Required on "VR046" - 1RC0477 or 1RC0478 24" High Curbs Required on "VR062" - 1RC0477 or 1RC0478 Model Number VR028A15M VR028A15H VR028A25M VR036A15H VR036A25H VR046A15H VR046
PAGE 20
903106-UTG-A-0912 Models Z42, X42 Z33, X33 Z34, X34 82.13 74.75 24.59 20.92 61.23 - Designed to meet unit specifications - 14’ High Curbs Required - Rooftop unit blower exceeds the capacity of the ERV Exhaust Blowers Model Number VR074A40L VR074A40V VR122A40L VR122A40V CFM 6000 - 8000 6000 - 8000 8000 - 13000 8000 - 13000 Description Constant Volume Variable Air Volume Constant Volume Variable Air Volume - See blower performance charts for airflow at various external static pressures.
PAGE 21
903106-UTG-A-0912 TABLE 12: BLOWER PERFORMANCE CHART - VR074 CFM 6000 6500 7000 7500 8000 Exhaust Blower RPM for VR074, (2) 5HP, Barometric Hood External Static Pressure (in water) 0 0.5 1 1.5 910 1060 1200 1300 955 1095 1225 1360 1000 1130 1260 1380 1040 1170 1290 1400 1080 1200 1315 1425 Notes: 1. Drive losses included in the above table 2. Performance can vary depending on ambient conditions 3.
PAGE 22
903106-UTG-A-0912 UPG UERV STAND ALONE MODEL NOMENCLATURE UPG UERV Model Nomenclature V D 011 N00 H 4 A AA 2 Product Generation Product Category 2 = Second Generation V = Ventilator Additional Options Wheel Type Voltage D = Stand Alone, Down Discharge O = Stand Alone, Over and Under S = Stand Alone, Side by Side 1 = 110v - 1ph 2 = 208/230v - 3ph 4 = 460v - 3ph 5 = 575v - 3ph 8 = 440v-1ph 9 = 208/320v - 1ph CFM* 011 = 300 to 1100 020 = 1200 to 2000 028 = 1200 to 2800 036 = 2000 to 3600 046 = 3000 to
PAGE 23
903106-UTG-A-0912 TABLE 14: FILTER SIZES - STAND ALONE ERV SERIES Series D O S Size Return Filter Width Height 14 20 16 20 20 20 16 20 24 24 14 20 18 20 20 20 18 25 16 16 20 20 16 / 14 20 24 24 14 20 14 20 16 20 20 20 16 20 24 24 14 20 Qty 1 2 2 3 2 5 6 8 1 2 2 2/1 2 5 1 2 2 3 2 5 011 020 028 036 046 062 080 120 011 020 028 036 046 062 011 020 028 036 046 062 Type 2" PLT 2" PLT 2" PLT Intake Filter Width Height 16.25 10.375 12.5 20 14.75 32.25 16.5 32.25 20 36 20 / 20 36 / 12.5 32.25 21.5 32.
PAGE 24
903106-UTG-A-0912 TABLE 15: SPECIFICATIONS AND ELECTRICAL DATA - 300 THROUGH 1100 CFM ERV'S D011 Stand Alone Down Discharge 208/230v 208/230v 460v 1ph 3ph 3ph Model Numbers Line Voltage - 60hz Motor - hp Wheel Size (dia x width) -in Motor Speed -rpm Fresh Air Motor Speed(s) Blower Bearing Type Full Load Amps Service Factor Motor - hp Stationary Wheel Size (dia x width) -in Motor Speed -rpm Exhaust Air Motor Speed(s) Blower Bearing Type Full Load Amps-Stationary Service Factor Potential Volts Wheel Electri
PAGE 25
903106-UTG-A-0912 TABLE 16: SPECIFICATIONS AND ELECTRICAL DATA - 1200 THROUGH 2000 CFM ERV'S D020 Stand Alone Down Discharge 208/230v 460v 575v 3ph 3ph 3ph Model Numbers Line Voltage - 60hz Motor - hp Wheel Size (dia x width) -in Motor Speed -rpm Fresh Air Motor Speed(s) Blower Bearing Type Full Load Amps Service Factor Motor - hp Stationary Wheel Size (dia x width) -in Motor Speed -rpm Exhaust Air Blower Motor Speed(s) Bearing Type Full Load Amps-Stationary Service Factor Potential Volts Wheel Electrical
PAGE 26
903106-UTG-A-0912 TABLE 17: SPECIFICATIONS AND ELECTRICAL DATA - 1200 THROUGH 2800 CFM ERV'S D028 Stand Alone Down Discharge 208/230v 460v 575v 3ph 3ph 3ph Model Numbers Line Voltage - 60hz O028S/A Over and Under S028 S/A Side by Side 208/230v 460v 575v 3ph 3ph 3ph Motor - hp / type Wheel Size (dia x width) -in Motor Speed -rpm Motor Speed(s) Bearing Type Full Load Amps Service Factor 3 / Belt 10 x 10 1725 Adjustable Sheave Ball 9.4 4.3 3.2 1.15 3 / Belt 10 x 10 1725 Adjustable Sheave Ball 9.4 4.3 3.
PAGE 27
903106-UTG-A-0912 TABLE 18: SPECIFICATIONS AND ELECTRICAL DATA - 2000 THROUGH 3600 CFM ERV'S Model Numbers Line Voltage - 60hz Motor - hp / type Wheel Size (dia x width) -in Motor Speed -rpm Fresh Air Motor Speed(s) Blower Bearing Type Full Load Amps Service Factor Motor - hp Stationary Wheel Size (dia x width) -in Motor Speed -rpm Exhaust Air Blower Motor Speed(s) Bearing Type Full Load Amps-Stationary Service Factor Motor - hp (1 phase) Wheel Electrical Potential Volts Data Motor Speed -rpm Full Load Amp
PAGE 28
903106-UTG-A-0912 TABLE 19: SPECIFICATIONS AND ELECTRICAL DATA - 3000 THROUGH 4600 CFM ERV'S Model Numbers Line Voltage - 60hz Motor - hp / type Wheel Size (dia x width) -in Motor Speed -rpm Fresh Air Motor Speed(s) Blower Bearing Type Full Load Amps Service Factor Motor - hp Stationary Wheel Size (dia x width) -in Motor Speed -rpm Exhaust Air Blower Motor Speed(s) Bearing Type Full Load Amps-Stationary Service Factor Enthalpy Wheel Electrical Data Total Electrical Wheel Data Curb Weights Motor - hp (1 ph
PAGE 29
903106-UTG-A-0912 TABLE 20: SPECIFICATIONS AND ELECTRICAL DATA - 4600 THROUGH 6200 CFM ERV'S Model Numbers CFM Range Line Voltage - 60hz Motor - hp / type Wheel Size (dia x width) -in Motor Speed -rpm Fresh Air Motor Speed(s) Blower Bearing Type Full Load Amps Service Factor Motor - hp Stationary Wheel Size (dia x width) -in Motor Speed -rpm Exhaust Air Blower Motor Speed(s) Bearing Type Full Load Amps-Stationary Service Factor Motor - hp (1 phase) Enthalpy Wheel Potential Volts Electrical Data Motor Speed
PAGE 30
903106-UTG-A-0912 TABLE 21: SPECIFICATIONS AND ELECTRICAL DATA - 6000 THROUGH 13000 CFM ERV'S D080 Stand Alone Down Discharge 208/230v 460v 3ph 575v 3ph 3ph 10 / Belt 15 x 15 1725 Adjustable Sheave Ball 26.8 13.4 10.3 1.15 D120 Stand Alone Down Discharge 208/230v 460v 3ph 575v 3ph 3ph 15 / Belt 22 x 15 1725 Adjustable Sheave Ball 41.0 18.5 15.4 1.15 7.5 / Belt 18 x 18 1725 Adjustable Sheave Ball 22.4 9.7 7.8 1.15 10 / Belt 22 x 22 1725 Adjustable Sheave Ball 32.6 13.4 10.3 1.
PAGE 31
903106-UTG-A-0912 D SERIES STAND ALONE ERV'S FOR DOWN DISCHARGE DUCT ARRANGEMENTS FEATURES AND NOTES 1. 2. 3. 4. 5. 6. Stand alone design allows higher levels of outdoor air to be introduced into the a/c space. Static test ports provided to verify intake and exhaust CFM. Balancing damper(s) field supplied in duct work when connected to ERV. Roof curbs are available for the ERV's. See blower performance charts for airflow at various E.S.P. EXHAUST AIR HOOD Filter rack with 2" pleated filters included.
PAGE 32
903106-UTG-A-0912 TABLE 22: AIRFLOW PERFORMANCE - DOWNFLOW CONFIGURATION FOR D011 & D020 Blower RPM for D011 CFM 300 500 700 900 1100 CFM 300 500 700 900 1100 SUPPLY Mist Eliminator Filter in Intake Hood (1.5HP) External Static Pressure (in water) 0 0.25 0.5 0.75 1 N/A N/A 1175 1350 1450 N/A 1170 1340 1540 1655 1295 1425 1600 1625 1795 1540 1660 1720 1790 2030 1785 1915 2025 2185 N/A 1.25 1605 1725 1960 2110 N/A 1.5 1730 1840 2035 2195 N/A EXHAUST Barometric Hood, 2" Pleated Filters (1.
PAGE 33
903106-UTG-A-0912 TABLE 23: AIRFLOW PERFORMANCE - DOWNFLOW CONFIGURATION FOR D028 & D036 Blower RPM for D028 CFM 1200 1600 2000 2400 2800 CFM 1200 1600 2000 2400 2800 SUPPLY Mist Eliminator Filter in Intake Hood (3HP) External Static Pressure (in water) 0 0.25 0.5 0.75 1 N/A 790 960 1110 1210 750 900 1005 1145 1230 900 1005 1105 1210 1275 1005 1125 1210 1275 1365 1125 1230 1315 1380 1450 1.25 1315 1365 1400 1450 1535 1.
PAGE 34
903106-UTG-A-0912 TABLE 24: AIRFLOW PERFORMANCE - DOWNFLOW CONFIGURATION FOR D046 & D062 Blower RPM for D046 CFM 3000 3400 3800 4200 4600 CFM 3000 3400 3800 4200 4600 SUPPLY Mist Eliminator Filter in Intake Hood (5HP) External Static Pressure (in water) 0 0.25 0.5 0.75 1 900 1030 1100 1165 1240 975 1085 1175 1240 1290 1070 1175 1240 1290 1350 1165 1240 1320 1350 1430 1240 1320 1375 1430 1500 1.25 1285 1350 1400 1465 1515 1.
PAGE 35
903106-UTG-A-0912 TABLE 25: AIRFLOW PERFORMANCE - DOWNFLOW CONFIGURATION FOR D080 & D120 Blower RPM for D080 CFM 6000 6400 6800 7200 7600 8000 CFM 6000 6400 6800 7200 7600 8000 SUPPLY Mist Eliminator Filter in Intake Hood (10HP) External Static Pressure (in water) 0 0.25 0.5 0.75 1 737 794 851 908 961 786 839 893 947 998 836 886 937 987 1036 885 931 979 1027 1074 934 978 1024 1069 1114 983 1025 1068 1111 1154 1.25 1012 1047 1083 1119 1159 1196 1.
PAGE 36
903106-UTG-A-0912 S SERIES STAND ALONE ERV'S FOR SIDE BY SIDE DUCT ARRANGEMENTS RETURN DUCT FLANGE OPENING SUPPLY DUCT FLANGE OPENING FEATURES AND NOTES 1. 2. 3. 4. 5. 6. Stand alone design allows higher levels of outdoor air to be introduced into the conditioned space. Static test ports provided to verify intake and exhaust CFM. Balancing damper(s) is field provided when connected to ductwork. System may not operate properly without balancing damper. Roof curbs are available for the ERV's.
PAGE 37
903106-UTG-A-0912 TABLE 26: AIRFLOW PERFORMANCE - SIDE BY SIDE DUCT CONFIGURATION FOR S011 & S020 Blower RPM for S011 CFM 300 500 700 900 1100 CFM 300 500 700 900 1100 SUPPLY Mist Eliminator Filter in Intake Hood (1.5HP) External Static Pressure (in water) 0 0.25 0.5 0.75 1 N/A N/A 1020 1205 1365 N/A 1015 1200 1320 1460 990 1190 1315 1455 1560 1150 1310 1450 1555 1660 1305 1440 1550 1655 1740 1.25 1480 1565 1665 1680 1815 1.5 1590 1670 1715 1795 1895 EXHAUST Barometric Hood, 2" Pleated Filters (1.
PAGE 38
903106-UTG-A-0912 TABLE 27: AIRFLOW PERFORMANCE - SIDE BY SIDE DUCT CONFIGURATION FOR S028 & S036 Blower RPM for S028 CFM 1200 1600 2000 2400 2800 CFM 1200 1600 2000 2400 2800 SUPPLY Mist Eliminator Filter in Intake Hood (3HP) External Static Pressure (in water) 0 0.25 0.5 0.75 1 N/A 955 1070 1210 1370 N/A 1065 1205 1305 1460 1060 1200 1290 1445 1530 1190 1335 1440 1490 1575 1300 1460 1550 1645 1705 1.25 1465 1540 1585 1670 1750 1.
PAGE 39
903106-UTG-A-0912 TABLE 28: AIRFLOW PERFORMANCE - SIDE BY SIDE DUCT CONFIGURATION FOR S046 & S062 Blower RPM for S046 CFM 3000 3400 3800 4200 4600 CFM 3000 3400 3800 4200 4600 SUPPLY Mist Eliminator Filter in Intake Hood (5HP) External Static Pressure (in water) 0 0.25 0.5 0.75 1 965 1085 1150 1230 1295 1035 1145 1250 1290 1335 1120 1245 1285 1315 1440 1215 1305 1355 1430 1465 1300 1375 1450 1460 1540 1.25 1345 1415 1470 1530 1590 1.
PAGE 40
903106-UTG-A-0912 O SERIES STAND ALONE ERV'S FOR OVER AND UNDER DUCT ARRANGEMENTS FEATURES AND NOTES 1. Stand alone design allows higher levels of outdoor air to be introduced into the conditioned space. Static test ports provided to verify intake and exhaust CFM. Balancing damper(s) is field provided when connected to ductwork. System may not operate properly without balancing damper. Roof curbs are available for the ERV's. See blower performance charts for airflow at various E.S.P.
PAGE 41
903106-UTG-A-0912 TABLE 29: AIRFLOW PERFORMANCE - DOWNFLOW CONFIGURATION FOR O011 & O020 Blower RPM for O011 CFM 300 500 700 900 1100 CFM 300 500 700 900 1100 SUPPLY Mist Eliminator Filter in Intake Hood (1.5HP) External Static Pressure (in water) 0 0.25 0.5 0.75 1 N/A N/A 1175 1350 1450 N/A 1170 1340 1540 1655 1295 1425 1600 1625 1795 1540 1660 1720 1790 2030 1785 1915 2025 2185 N/A 1.25 1605 1725 1960 2110 N/A 1.5 1730 1840 2035 2195 N/A EXHAUST Barometric Hood, 2" Pleated Filters (1.
PAGE 42
903106-UTG-A-0912 TABLE 30: AIRFLOW PERFORMANCE - DOWNFLOW CONFIGURATION FOR O028 & O036 Blower RPM for O028 CFM 1200 1600 2000 2400 2800 CFM 1200 1600 2000 2400 2800 SUPPLY Mist Eliminator Filter in Intake Hood (3HP) External Static Pressure (in water) 0 0.25 0.5 0.75 1 N/A 790 960 1110 1210 750 900 1005 1145 1230 900 1005 1105 1210 1275 1005 1125 1210 1275 1365 1125 1230 1315 1380 1450 1.25 1315 1365 1400 1450 1535 1.
PAGE 43
903106-UTG-A-0912 TABLE 31: AIRFLOW PERFORMANCE - DOWNFLOW CONFIGURATION FOR O046 & O062 Blower RPM for O046 CFM 3000 3400 3800 4200 4600 CFM 3000 3400 3800 4200 4600 SUPPLY Mist Eliminator Filter in Intake Hood (5HP) External Static Pressure (in water) 0 0.25 0.5 0.75 1 900 1030 1100 1165 1240 975 1085 1175 1240 1290 1070 1175 1240 1290 1350 1165 1240 1320 1350 1430 1240 1320 1375 1430 1500 1.25 1285 1350 1400 1465 1515 1.
PAGE 44
903106-UTG-A-0912 GUIDE SPECIFICATIONS Prepared for the guidance of architects, consulting engineers, and mechanical contractors. GENERAL Furnish and install _____________ mechanical cooling system, complete with a Unitized Energy Recovery Ventilator (UERV). APPROVALS The Unitized Energy Recovery Ventilator will contain an energy recovery component rated in accordance with AHRI/ ANSI Standard 1060-2005 with ratings certified by AHRI.
PAGE 45
903106-UTG-A-0912 OPTIONS 2. The ERV is activated with the supply blower of the RTU. The intake blower, the exhaust blower, and the wheel rotation motor of the ERV are activated. These motors will remain energized as long as the supply blower on the RTU is energized and the RTU is in standard (noneconomizer) mode. 3. If the optional motorized fresh air damper in the outside air intake of the ERV is present, it opens and the ERV is energized. 4.
PAGE 46
903106-UTG-A-0912 UERV TROUBLESHOOTING GUIDE UERV BELOW 600 CFM WITH STATIONARY WHEEL (NO ECONOMIZER) 4. If all of the above are operational, the exhaust motor is bad. Replace it with new motor. UERV will not operate. UERV has power, but the fresh air blower does not operate. 1. 1. Verify the A130 circuit board switch SW1 Power is in the "on" position. 2.
PAGE 47
903106-UTG-A-0912 control, etc.). Typically, "1" would be from the blower contactor on an a/c unit. 2. Verify high voltage power to UERV. a. b. tactor terminal "A" and "B", and that the contacts are closed. 3. Check for correct voltage for UERV to L1 and L2 on 1-phase units. Verify power to B27 fresh air blower motor though J/ P148 plug assembly. 4. Check for correct voltage for UERV to L1, L2, and L3 on 3-phase units. On direct drive models, verify B27 wheel motor C26 capacitor is good.
PAGE 48
b. Check for correct voltage to L1, L2, and L3 on 3phase units. c. Verify the F29 fuses are good. Replace any bad fuses. c. Verify power to B27 fresh air blower motor though J/ P148 plug assembly. d. Verify that the T27 transformer has the UERV voltage correctly applied to the correct transformer terminals. d. On units equipped with the optional low ambient control, verify that the circuit on the A130 circuit board terminal "5" and "6" is made.