User Manual

User Manual
YNE3-RX
E-TTL Wireless Flash Receiver
LI NK
YNE3-RX
E-TTL Wireles s Flash Receive r
R
E
L
/
E
T
A
S
S
E
E
T
Read this user manual while also referring to
your camera's & flash's user manual before
using in order to correct use this product.
FPlease turn off power supplies of all equipment
when connecting or installing the product.
FPlease don't make products subject to strong
v i b r a t i o n , o t h e r w i s e t h e p r o d u c t m a y
malfunction.
FLong time when not in use, please put the
receiver's power off, remove the battery.
FPlease keep it dry. Be sure not to use wet hand
to touch the product. It is also not allowed to
immerse the product into waster or make it be
exposed in the rain, otherwise it may not work
normally or even be damaged.
FDo not store under high temperature, such as a
covered car under direct sunlight, the dashboard
and other high-temperature place.
FDo not use it in explosive situations, violation
of this warning may cause an explosion or fire.
FThis product involves batter y, please be in
strict accordance with the relevant provisions on
the use of the battery, otherwise it would cause
property damage or personal injury.
Cautions
V1.0
Specifications
Type:
Distance:
Channel:
Groups:
Frequency:
Wireless ID:
USB firmware upgrade:
Compatible battery:
Working time:
Size:
Weight:
Accessories:
Wireless flash receiver
100M
AUTO, Ch. 1-15
5 groups(A/B/C/D/E)
2405-2475MHz
0000-9999
Support
A A X 2 ( s u p p o r t s 1 . 2 V
rechargeable batteries)
24 hours
92.5*50*37mm
70g
Receiver X1 PC-635 sync c
ord X1 6.35-3.5 adapter X1
User manual X1 warranty
card x1
Firmware Update
1 . L o g i n t h e YO N G N U O of f i c i a l we b s i t e
( h t t p : / / w w w . h k y o n g n u o . c o m / e -
detaily.php?ID=360) to download the firmware
update software and the latest firmware.
2.Power off, use USB-MINIB cable(not include)
connect to PC.
3.Press the <SET> button and set the power
switch to <ON> ,the LCD will display current
version, that into firmware upgrade interface.
4.Complete the firmware upgrade operation
according to the prompt of software.
PC Port Triggering
Caution!
Do not connect to the PC port
a n y f l a s h r e q u i r i n g t r i g g e r
voltage more than 300V, or the
receiver may be damaged.
The PC port is for output using only.
Flashes on the hot shoe and connecting to
the PC port can be used at the same time.
Wireless Shutter Release
1.Install the compatible master unit which
supports wireless shutter release on the
camera, such as YN-E3-RT.
2.Long press the【 TEST/RELEASE】 button of
the receiver will release the camera shutter,
if the receiver installed a flash, it will
synchronous flash according to the master
unit.
Only support single shot.
The function is not supported when the
camera using “Bulb” mode.
As for the EOS digital cameras released
after 2012, regarding to the shutter release
connection of the master unit, please refer
to its user manual.
The functions of this user manual are based on test
conditions of our company. Further notice will not
be given if the design and specifications change.
The YONGNUO logo in this manual includes the
registered trademark or trademark of Shenzhen
Yongnuo Photography Equipment Co. ,Ltd in China
o r / a n d o t h e r c o u n t r i e s ( r e g i o n s ) . A l l o t h e r
trademarks are the property of their respective
owners.
Clear flash receiver settings
Press the 【 SET】 and 【 -】 buttons at the
same time, the screen will display "CLA" and
the receiver will restore factor y settings.
The flash screen and receiver screen will
display the flash mode and output of
current flash when finish flashing.
When using the universal( )
flash, it need manual adjust the flash
output,the recycling state will not return to
the master transmitter.
single contact
The compatible transmitter(master unit):
YN-E3-RT/YN600EX-RT/ST-E3-RT/600EX-RT
Parts of the compatible E-TTL flash list:
Canon 600EX(RT)/580EXII/430EXII
Yongnuo YN568EX(II)/YN565C/YN468C(II)/
YN467C(II)/YN465C
Name of Parts
Purchase corresponding PC flash sync
cord according to the flashes needs.
1.Use an end of PC sync cord with nuts to the
receiver. The other end of the PC sync cord
connects to strobe flashes or other flashes
which supporting PC port.
2.Adjust flash output and shoot.
Operate the master unit, set the flash
group and flash output, when pressing the
shutter release button, the flash on the
recei ver wil l f ire. Sup por ts maxi mum 5
groupings, total 15 units.
LINK
YNE 3-RX
E-TTL Wireless Flash Receiver
/
R
E
L
E
A
S
T
S
E
E
T
①
②
Wireless Flash Trigger
Mounting foot: Fix on the fixed stand through the
hot shoe screw nut or through the hot shoe
adapter.
PC : Connect the flash as output.
Test/shutter button: Half press, short press for
flash test; long press for remote shutter Radio
transmission confirmation indicator.
Radio transmission confirmation light(LINK):
Connect the master unit will bright on the green
light, not connected will bright on red light.
Hot shoe : install the flash.
Battery compartment: Install two AA batteries.
Power switch:【ON】power on,【OFF】power off.
LCD display screen: Display the icon of flash
mode, flash output power , Id, channel, grouping,
battery indicator and etc.
Set button: Press the【 SET】 button to
choose the parameters as needed, press the
【+】 、 【-】button to change the parameters. No
operation in 5 seconds or long press the【 SET】
button will save the parameters.
【+】、【-】button： Change the parameters.
Port
【 】 setup
USB upgrade interface: Connect the computer
for firmware upgrade
Id
Batter y
compartment
Batter y door
Mounting foot
PC port
USB upgrade interface
Radio transmission
confirmation indicator light
【SET】Setup button
【+】 button
【-】button
Power switch
LCD
Display
screen
Hot shoe
Test/shutter button
ETTL:
Auto flash
Gr:
Group firing
Ch:Channel
M:Manul flash
Multi:
Stroboscopic flash
Id/flash output
Batter y indicator
LCD
Flash output trim
E
L
R
/
E
A
T
S
S
E
E
T
【TEST/RELEASE】
Example
Function Introduction
Th e p ro d u ct sh o u l d b e u sed w i th the
compatible master unit(transmitter), this
manual is assume that used with the YN-E3-RT
as the transmitter, concerning the settings and
operation of the transmitter, please refer to
the user manual.
Supports flash mode: ETTL,M,MULTI
Supports remote shutter release function,
test flash
Supports PC output interface
Supports USB firmware upgrade
Supports single contact triggering
Supports single contact flash triggering
LCD Display
When the battery displays
< >，please replace the batter y in time.
Please take off the batteries when you do
not use the product for a long time.
When replacing the batteries, please
replace the two batteries together.
About the LCD Panel Illumination
When operating the buttons, the LCD will
bright with green in a few seconds.
When setting the functions, the light will last
until the setting finish.
indicator
2.Fix the receiver,install the flash
1)Fix on the light bracket through the hot shoe
screw nut or hot shoe foot.
2)Loose the flash locking device, insert the
flash hot shoe fixed foot into the receiver
hot shoe.
3)Lock the flash.
Note: The hot shoe of receiver can only used
with the flash which suitable for the DSLR
cameras, could not used with the high
voltage flash, otherwise it may damage the
receiver.
Preparation Before Use
1.Install two batteries
Set the Channel,Grouping,ID
The transmitter and receiver need to set
to the same channel and wireless radio ID
for use.
Slide the power switch to the【 ON】 will turn
on the power supply, slide to【 OFF】 will turn
off the power supply.
3.Turn on the power
1.Channel setting
Press the【 +】 、 【 -】 to choose AUTO or
channel 1-15.
2.Group setting
P r e s s t h e 【 S E T 】 b u t t o n u n t i l t h e
corresponding Gr number blinking.
Press the 【 +】 、 【 -】 to choose A-E five
groups.
3.Wireless radio ID setup
 P r e s s t h e 【 S E T 】 b u t t o n u n t i l t h e
corresponding Id number blinking.
Press the【 +】 、 【 -】 button to select the
location set and number.
Press the【 SET】 button,the corresponding
Ch number will blink.


Test flash
Use the transmitter or receiver test button
to test the flash. You can short
press the【TEST/RELEASE】button on YNE3-RX
to test the flash.
half press or
Id
LI NK
YN-E3-RT
YNE3-RX
Preparation Before Use
Wireless Connection State
Id
①
②
When transmission between the receiver
and transmitter is established, the <LINK>
indicator light bright on green.
E
L
R
/
E
A
T
S
S
E
E
T
Open the battery compartment, install two AA
batteries(not include) according to the battery
positive and negative poles (you can use two
1.2V rechargeable batteries),then close the
battery door.
LS-PC635
LS-PC/PC
(Options)