Contents Precaution . . . . . . . . . . . . . . . . Features . . . . . . . . . . . . . . . . . Quick Start . . . . . . . . . . . . . . . . Components Description . . . . . . . . . . LCD Panel . . . . . . . . . . . . . . . . Installation Instruction. . . . . . . . . . . Basic Operations . . . . . . . . . . . . . Wireless Flash Shooting . . . . . . . . . . Advanced Applications . . . . . . . . . . . C.Fn/P.Fn: Setting Custom /Personal Functions Shooting with LED Light . . . . . . . . . . Troubleshooting . . .
Features Equipped with LED Light Equipped with a high power LED light of high power, brightness can be adjusted, there is a built -in diffuser and a color conversion filter for the LED light.
Quick Start If you don't have much time to read the whole user manual, we advise you to read this section. 1.Please avoid the excessive use of the output with maximum power. It can effectively extend the ser vice life of this product. (It is recommended that the speedlite should be idle for more than 3 minutes when entering the overheat protection). 2.Short press the function button [ ] and [MODE] button can switch the trigger mode and flash mode (Gr flash mode only in wireless master mode). 3.
Components Description Wide refection board Built -in diffuser(for LED light) Wide panel Flash head LED light Optical transmission wireless sensor LED button Color conversion filter (for LED light) AF-assist beam emitter Terminal cover PC port External power source port Mini stand USB port hotshoe contact Bounce angle index Radio transmission confirmation lamp (LINK lamp) LCD panel Function button 1/2/3/4 Trigger mode button Flash mode button Batter y compartment cover Charging lamp/ Test flas
LCD Panel ETTL flash Focal length Zoom: A :Automatic M ：FEB FEB sequence :Manual ：Beep ETTL：ETTL auto flash :Standard ：Auto zoom for sensor size ETTL M Zoom 20 mm ：High-speed sync :Over heat F5.6 :Bounce Zm C.Fn fEB SYNC ：Second-curtain sync F:Apeture ：FEC FEC amount Flash exposure level Manual flash M:Manual flash M M Zoom 20 mm Manual flash output 0.3 Zm C.
LCD Panel Short press the button [ ]can switch the trigger mode: set top, radio wireless master mode, radio wireless slave mode, optical wireless slave mode(include SC/SN/SC&SN/S1/S2） :Set on flash :Master flash firing ON :Master flash firing OFF ETTL M Zoom 24 mm CH 1 RAT A B C AB 11 C Zm C.
Installation Instruction 1、Install Batteries Slide the batter y compartment cover in the direction of the arrow as shown. Insert the batteries according to the label inside batter y compartment and make sure the direction of the batter y contact (+/-) is correct. Close the batter y compartment cover in the direction of the arrow as shown.
Basic Operations 1.
Basic Operations 3.Meaning of [Link lamp] [LINK] lamp statues Meaning Method Green light Transmission OK. Normal Red light Not connect. Check if the channel and ID of the master unit and slave unit are consistent. Orange Used as the second and the subsequent master unit Normal 4.The meaning of [Sound Prompt] The Sound Form Meaning Method Tick-a short sound Wireless transmission OK Tick---a long sound The speedlite is fully charged, and can be used.
Basic Operations 5.ETTL Mode In ETTL mode, the metering system of this camera will detect flash illumination reflected back from the object so as to automatically adjust the exposure compensation. In ETTL mode, the light intensity can be adjusted by setting FEB, FEC and flash exposure lock(FEL). 6.M Mode In M mode, you can set flash output as your requirement by short press the function button [ ],when the [Flash output level] displays on the screen, you can adjust the flash output through [ ].
Basic Operations 10.Auto zoom： Short press the function button [ Zm C.Fn ] until the local length value displays on LCD panel, then adjust the coverage through [ ]. When it displays[ ],attach the speedlite to the camera, the flash coverage will change as the lens focal length and move back and forth to commodate different flash coverage . 11.Manually set the zooming position: Press the function button [ Zm C.Fn ]until the local length value displays on LCD panel, then adjust the coverage through[ ].
Wireless Flash Shooting: Radio Transmission Using a transmitter or a speedlite compatible with radio transmission wireless shooting makes it easy to shoot with advanced wireless multiple flash lighting, in the same way as normal E-TTL II/E-TTL autoflash shooting. The system is designed so that the settings of the transmitter attached to the camera (master) are automatically reflected on the Speedlite that is wirelessly control led (slave). Therefore, you do not need to operate the slave unit while shooting.
Wireless Flash Shooting: Radio Transmission Press the function button[ ] to set the master flash firing on or off. Press the function button [ RATIO ] to set the firing group. Press the function button[ ] and rotate the [ ]can adjust the exposure compensation (or flash output). ETTL M Zoom 24 mm AB E3 CH 1 RAT A B C 11 C RATIO Gr MENU2 About Master Units You can use two or more master units (master units + slave units =maximum of 16 units).
Wireless Flash Shooting: Optical slave mode Short press the button [ ] until displays the [ ]and [ ]. Select a trigger mode when press the function button 4 [MENU] displays the SC/SN/SC&SN/S1/S2 trigger modes*. Please allow the wireless trigger sensor face to the master flash by rotating the flash head. Before shooting, the slave unit and master unit should Outdoors Indoors be set on the same channel.
Wireless Flash Shooting Wireless Multi Flash Shooting In wireless flash shooting you can create 1~5(up to three groups: A/B/C in wireless shooting optical transmission) slave unit groups to achieve multifaceted flashing, and the master unit set up the flash ratio of TTL auto flash shooting ,flash output, multi flash or Gr mixed mode flash.
Advanced Applications 1.Flash Exposure Compensation(FEC) In order to make the shooting effect more suitable to your needs, you can set the flash exposure compensation through the camera or on the flash. The exposure compensation value is within the range of -3EV~+3EV. lt can be set through pressing the function button [ ]and rotating the [ ]. NOTE: Please note that this compensation setting will overlap the exposure compensation setting on the camera.
Advanced Applications 6.Use Wide Panel Pull out the Wide panel, push back the Reflection board and arrange them as per the figure; in such case, the flash scopes will extent to 14 mm ,the flash range will be enlarged and the effect will be softer and more natural. 7.
Advanced Applications 10.Short Distance Flash Shooting When you position the flash head down by 7° , you can shoot subjects at a short distance in a range of approx. 0.5 to 2 m. 11.PC Sync port (input) Through connecting to the PC sync por t, you can make the flash synchronously. 12.Use the External Batter y Pack You can purchase the external batter y pack SF-18C or SF-17C,connect it to the external power socket of the speedlite, even when using external power, insert batteries into the speedlite.
Advanced Applications 16.Linked shooting with radio transmission* Linked shooting is a function that automatically releases the shutter of a slave unit camera by linking it to a master unit camera. You can shoot with linked shooting for up to 16 units, including both master units and slave units. This is convenient when you want to shoot a subject from multiple angles at the same time.
C.Fn/P.Fn: Setting Custom /Personal Functions Long press the function button [ ] to enter into the custom function, rotating the [ ] to choose the items which need adjusted. Then press the [OK] button to enter into the program setting mode, rotating the [ ]to select the option and press [OK] button. After finishing the custom settings, press the function button [ ] return to the ready shooting state. press the function button[P.
C.Fn/P.Fn: Setting Custom /Personal Functions C.Fn-22: (LCD panel illumination) When a button or dial is operated, the LCD panel illuminates. You can change this illumination setting. 0: 12sec (On for 12 sec.) 1: OFF (Disable panel illumination) 2: ON (Illumination always on) C.Fn-23: 0: 1: / (Slave flash batter y check) （(AF-assist beam, lamp)） ( lamp) C.Fn-25: Through the function button [MENU] can witch to the wireless optical slave mode.
Shooting with LED Light Using the LED light 1.Make the flash unit vertical（90°upward bounce） 2.Press the [LED]button， the LED comes on, the LED lighting on the LCD panel. 3.Rotate the [ ]to adjust the brightness. 4.Press the [LED] button again or press the function button[ ]to turning off the LED light.
Troubleshooting 1 .Power does not turn on or the flash dose not fire. Make sure that the batteries are installed in the correct orientation. Please check if the speedlite is in overheat protection status. lf the electrical contacts of the speedlite and camera are dirty, clean the contacts. 2.The flash automatically shut off the power Please check if the flash enable the power saving mode or whether the batter y power is enough. 3.
Specifications Circuit design: Guide No.
