Precaution To avoid fire or electrical shock , do not expose this product to rain or moisture. To avoid short circuit, please make sure the batteries contacts are securely packed and use the batter y in accordance with the local provisions. Please place the batteries and the parts which can be swallowed mistakenly away from children. If swallowed, please get medical help immediately. To avoid any possible injur y to eyes, do not use the flash in a short distance from the eyes.
Features Adopts lithium batter y power supply design, ultra-fast charging recycle system Equipped with 1800mAh lithium batter y, recycle time is only 1.5s, flash firing times of full output is over 700. Supports radio transmission master control, realizes 6-group flash control function easily.
Quick Start If you don't have much time to read the whole user manual, we advise you to read this section. 1.Please avoid the excessive use of the output with maximum power. It can effectively extend the ser vice life of this product. (It is recommended that the speedlite should be idle for more than 10 minutes when entering the overheat protection). 2.
Components Description Wide refection board Wide panel Bounce angle index Radio transmission confirmation lamp (LINK lamp) [ ] Trigger mode/ Channel button Flash head LCD panel Optical transmission Flash mode button wireless sensor Batter y Lock-release button Li-ion Batter y(kit only) [Gr/Fn]Group/Custom Function button Charging lamp/ Test flash button Mounting foot lock lever [ ] Set/Sound Button Power switch Terminal cover Selection/Setting button set Lock-release button Dust- and waterresista
LCD Panel Manual Flash Mode :On-Camera Mode :Radio wireless master mode :Radio wireless slave mode M:Manual flash MULTI：Multi flash M M:Manual Flash Mode :Optical wireless slave mode :Optical wireless slave mode Flash output ：Batter y level ：Over heat Gr:Group Ch:Channel ：Sound Multi Flash Mode Zoom MULTI：Multi Flash Flash output -5- Flash frequency Number of flashes
LCD Panel Short press [ ]button to switch the mode to on-camera,radio transmission master control,or radio transmission slave,long press this button to switch to S1/S2 of optical slave mode.In on-camera and master control mode,the LCD backlight is on in green,in slave mode,LCD backlight is on in orange.
Installation Instruction 1.Install Batter y And Take Out Batteries According to the picture, insert the lithium batter y fully into the batter y compartment ,the batter y will be installed when a 'click' sound comes out from the batter y locking lever. For taking out the lithium batter y, turn the batter y locking lever according to the direction of arrow, the lithium batter y will be popped out automatically. 2.
Basic Functions 1.Button Operation Turn to "ON"、“OFF”to turn on or turn off the power source of the flash.
Basic Functions 4.
Basic Functions 6.Power-on and Power-off Set the power switch to [ON] position, the speedlite will turn on and start charging. After turned on, the [Charging lamp] will bright with red light which indicates it can flash. After use, set the switch to [OFF] position to turn off the power source. 7. Test Flash When the charging lamp turns red, you can test the flash is normal or through the [TEST] button. 8.
Basic Functions 9.Multi Mode Multi mode, the speedlite will flash according to the flash output, flash frequency and number of flashes you set. Use [left][right]to adjust output power. The adjustment scope of output level is 1/128-1/64-1/32-1/16-1/81/4. To adjust times of flash and flash frequency, please press [ ] first to enter focal length setting menu, then press [ ] again to select the item (blink) to be set, at this time, user can adjust times of flash and flash frequency. 10.
Wireless flash shooting: Radio transmission When YN860Li is used as master unit, it can remotely alter flash mode, output, stroboscopic times, stroboscopic frequency and focal length of YN860Li/YN660/YN560IV/YN560III/YN968N which are set to slave unit mode, it can control slave unit parameters of 6 groups at most, it is also compatible with RF605,RF603(II),RF-602 series wireless flash trigger.
Radio Transmission Slave Unit Setting Short press the [ ] button of the speedlite until [ ] displays, the flash is set to be slave unit. Long press [ ]button to set slave unit and master unit to be in the same channel. Short press [ ]to set the grouping(A-F)of the slave unit. Radio Transmission Flash Shooting Short press master unit [ ] button to select grouping orderly, press [MODE] to set the flash mode of the current group, the speedlite supports M/MULTI flash mode and --(no flash).
Wireless Flash Shooting: Optical slave mode(S1/S2) Short press the [ ] button unit [S1] or [S2] icon is display. The two modes are also suitable for off-camera slave unit, for create a variety of lighting effects, which is suitable for manual flash and TTL flash environment. The two modes are same as M mode when adjusting the flash output. When using the S1\S2 mode, you can rotate the flash head to make the sensors face to the master unit.
Advanced Applications 1.Use Wide Panel Pull out the Wide panel, push back the Reflection board and arrange them as per the figure. The flash range will be enlarged and the effect will be softer and more natural. 2.Reflection Flash Bounce flash means to take photos by making flash light head aimed at wall or ceiling and using the light reflected back from the ceiling or wall to light the desired object, so that the shade behind the object can be decreased to get more natural shooting effect.
Advanced Applications 4.Short Distance Flash Shooting When you position the flash head down by 7° , you can shoot subjects at a short distance in a range of approx. 0.5 to 2 m. 5. PC Sync port (input) Through connecting to the PC sync port, you can make the flash synchronously. 6. High-speed Continuous Shooting The flash can support the high-speed continuous shooting function. Please set the camera in the continuous shooting form and then shoot. 7.
C.Fn:Setting Custom Functions Long press the function button [ ] on the speedlite to enter customs function setting, press[up]or [down] button to select the items need to be adjusted, press [left] or [right] to alter setting, press [OK] to confirm and exit setting. C.Fn-01: Power saving function( Auto Power Off ) in on-camera mode and master control mode Applicable Mode: On-camera mode and master control mode 05-120: Represents number of minutes after entering power save mode.
C.Fn:Setting Custom Functions C.FN-04: Grouping in radio transmission A-C: The speedlite can be set to A/B/C group A-D: The speedlite can be set to A/B/C/D group A-E: The speedlite can be set to A/B/C/D/E group A-F: The speedlite can be set to A/B/C/D/E/F group C.FN-05:Light duration of display backlight 05-12:Number of seconds of backlight lighting time. C.
Specifications Circuit design: Guide No.
Troubleshooting 1 .Power does not turn on or the flash dose not fire. Make sure that the batteries are installed in the correct orientation. Please check if the speedlite is in overheat protection status. lf the electrical contacts of the speedlite and camera are dirty, clean the contacts. 2.The flash automatically shut off the power. Please check if the flash enable the power saving mode or whether the batter y power is enough. 3.
