User Guide

Your X3 Alarm Controller connects to
the internet via one of our hubs (original
YoLink Hub or the SpeakerHub), and it
does not connect directly to your WiFi or
local network. In order for remote access
to the device from the app, and for
full-functionality, a hub is required. This
guide assumes the YoLink app has been
installed on your phone, and a YoLink
Hub or SpeakerHub is installed and
online.
If installing the X3 Alarm Controller and
Siren Horn outdoors, please refer to the
environmental range information in the
specifications found on the X3 Alarm
Controller product support page. While
this product can be installed outdoors, to
ensure years of trouble-free operation, it
should be protected from rain and direct
sunlight by an enclosure or overhead
cover.
Quick Start Guide
YS7105-UC & Siren Horn
X3 Outdoor Alarm
Controller
Revision Feb. 24, 2023
Welcome!
A
Thank you for purchasing YoLink
products! We appreciate you trusting
YoLink for your smart home & automa-
tion needs. Your 100% satisfaction is our
goal. If you experience any problems
with your installation, with our products
or if you have any questions that this
manual does not answer, please contact
us right away. See the Contact Us
section for more info.
Thank you!
Eric Vanzo
Customer Experience Manager
The following icons are used in this guide to
convey specific types of information:
Very important information
(can save you time!)
Pour des instructions en
français, scannez les codes
QR dans la section suivante.
Para obtener instrucciones en
español, escanee los códigos
QR en la siguiente sección.
Fr
Es
Before You Begin
B
Installation & User
Guide
Product Support
Support produit
Soporte de producto
You can also find all current guides and
additional resources, such as videos and
troubleshooting instructions, on the X3
Alarm Controller Product Support Page
by scanning the QR code below or by
visiting:
https://shop.yosmart.com/pages/x3-
alarm-controller-product-support
Please note: this is a quick start guide,
intended to get you started on the
installation of your X3 Alarm Controller.
Download the full Installation & User
Guide by scanning this QR code:
Get to Know Your X3
Alarm Controller
E
Get to Know Your X3
Alarm Controller, Cont.
E
Status LED
Mounting Holes (2)
SET Button
12VDC Output
LED Behaviors
Blinking Red Once, Then Green
Once
Device Start-Up
Blinking Red And Green
Alternately
Restoring to Factory Defaults
Blinking Red Once
Valve Closing
Quick Blinking Red Twice
Valve is Closed
Blinking Green Once
Valve Opening
Quick Blinking Green
Control-D2D Pairing in Progress
Quick Blinking Red
Control-D2D Unpairing in
Progress
Slow Blinking Green
Updating
Fast Blinking Red Once Every
30 Seconds
Low Battery, Replace Battery
Soon
Wall Anchors
Drill with Drill Bits Medium Phillips
Screwdriver
Required Items
The following items will be required:
The following items may be required:
D
In the Kit
C
1 x ER34615
Battery
Pre-Installed
X3 Alarm
Controller
Siren Horn
ES-626
Quick Start Guide
Mounting Holes (3)
Tilt Adjustment
Mounting Base
Get to Know Your Siren
F
To power up the
alarm controller for
the first time, press
SET button briefly,
unless the LED
flashes red then
green.
Power Up
G
Add Your X3 Alarm
Controller to the App
H
1. Tap Add Device (if shown) or tap the
scanner icon:
Scanner icon
2. Approve access to your phone’s
camera, if requested. A viewfinder will be
shown on the app.
3. Hold the phone over the QR code so
that the code appears in the viewfinder.
If successful, the Add Device screen will
be displayed.
You can change the device name and
assign it to a room later. Tap Bind
device.
If successful, the message “You have
successfully added this product!” will be
displayed. Tap Done.
4. Confirm the Outdoor Alarm Controller
is noted as being online before proceed-
ing to the next section. If not,
double-check the steps in the Power Up
section.