Operation Manual

7-8
IM 1F5B2-01E
.oNretemaraPnoitpircseDdaeRetirWegaRataDtinUtluafeD
C2TES2retemaraPputeS
01CEDOMLATOTedomnoitazilatotfoeciohCseYseYdelacsnurodelacS%delacS
11CETARLATOTnoitazilatotfoetaRseYseY)2etoN(00023ot10000.004B/p1
02CEDOMESLUPtuptuoeslupfoeciohC
edom
seYseYdelacsnurodelacSdelacS
12CETARESLUPtuptuoeslupfoetaRseYseY00023ot10000.004B/p1
03CTINULAICEPStinulaicepSseYseYsretcarahcciremunahpla8
)3etoN(
04B/p.EPS
13CTINUESABotnoisrevnocroftinucisaB
tinulaiceps
seYseYm
3
notrogk,l,04B/pm
3
23CAFVNOCTINUnoisrevnocroftneiciffeoC
tinulaicepsot
seYseY00023ot10000.013C/S1
06CKCEHCFLESegassemtset-fleSseYoNRORREroDOOG
noitacidni
-
DTSUJDAretemaraPevitcerroC
01DAm4MIRTAm-4rofgninut-eniF
tuptuo
seYseY01ot1-%0.0
11DAm02MIRTAm-02rofgninut-eniF
tuptuo
seYseY01ot01-%0.0
02DTSUJDARESUresunirotcafnoitcerroC
noitacilppa
seYseY00023ot10000.01
06DKCEHCFLESegassemtset-fleSseYoNRORREroDOOG
noitacidni
-
ELORTNOCretemaraPlortnoC
01ETESERLATOTeulavdezilatotfognitteseRseYseYetucexeottonroetucexEetucexeottoN
02ETCELESPSIDnosmetiatadmorfeciohC
yalpsid
seYseY)%(etar,latot,etar,)%(etaR
etarrolatot&etar,latot&
etar&)%(
)%(etaR
06EKCEHCFLESegassemtset-fleSseYoNRORREroDOOG
noitacidni
-
FTSETretemaraPtseT
01FEDOM%TEStnerrucfotuptuOseYseY011ot0%0.0
02FEDOMFTEStuptuoesluPseYseY0006ot0zH0.0
06FKCEHCFLESegassemtset-fleSseYoNRORREroDOOG
noitacidni
-
.1nahtrehtoeulavatesuoyfieulavdezilatotehtroftinuynawohstonseodyalpsidehT:2etoN
.deyalpsiderasretcarahcxistsrifehtylnO:3etoN
● Setting the totalization rate (applies only to models with an indicator/totalizer component)
The totalization rate is a parameter that sets the kg per rate of the totalizer value for a case where the
value is shown on the indicator. The flowrate set in parameter B40 applies as the totalizer value.
Example: Setting to totalize as 100 counting per 1kg.
<1> Make sure in parameter B40, ‘kg’ is selected as the unit of flowrate.
<2> Make sure in parameter C10, ‘SCALED’ is selected.
<3> In this parameter C11, set the rate at 100.
C11
● Setting the pulse output rate
The pulse output rate is a parameter that sets the liter per rate for a case where the pulse output is fed to
a counter or other device. The flowrate set in parameter B40 applies as the pulse output.
Example: Setting to output as 1000 pulse 1 liter.
<1> Make sure in parameter B40, ‘l’ is selected as the unit of flowrate.
<2> Make sure in parameter C20, ‘SCALED’ is selected.
<3> In this parameter C21, set the rate at 1000.
C21