Instruction Manual
7-1
IM 01R04B04-00E-E 8th edition March 01, 2011 -00
All Rights Reserved. Copyright © 2003, Rota Yokogawa
The table below shows an overview of functions of ROTAMASS RCCT3/RCCF31/RCCR31.
In brackets the related chapters in this manual are indicated.
Static
pressure
control
Density
offset
Total
reset
Device
S/W date
MF xed
value
Reference
density
Temperature
Gain adjust
Total
reset cntrl
Device S/W
version
MF x val
sel
Density x
val sel
Tempera-
ture xed
value
Total at
alarm
Hardware
rev
Mass ow
alm 2 crit
Vol ow
alm 2 crit
Density
alm
2 crit
Tempera-
ture x val
select
Total limit
switch
Software
rev
Mass ow
alm
2 sel
Vol ow
alm 2 sel
Density
alm
2 sel
Tempera-
ture
alm 2 crit
SO1
active
mode
SO2 ac-
tive mode
Total
switch
select
Fld dev
rev
Hardware Write Protect
(6.4)
Mass ow
alm1 crit
Vol ow
alm 1 crit
Density
alm
1 crit
Tempera-
ture
alm 2 sel
SO1
function
SO2
function
Heat of
combus-
tion unit
Gas
measure-
ment
(7.26)
Universal
rev
Mass
ow alm
1sel
Vol ow
alm 1
sel
Density
alm
1 sel
Tem-
perature
alm 1 crit
Pulse 1
at alarm
Pulse 2
at alarm
Heat of
combus-
tion
Error
history
(8.2)
Fluid
max.
Temp.
(7.25)
Dev id
Mass
ow
lowcut
Vol ow
lowcut
Density
lowcut
Tempera-
ture
alm 1 sel
Pulse 1
width
Pulse 2
width
Total
energy
unit
History
overview
(8.2)
Corrosion
detection
(7.22)
Date
Key Sta-
tus
HART
Mass
ow
damping
Vol ow
damping
Density
damping
Tempera-
ture
damping
Pulse 1
active
mode
Pulse 2
active
mode
Total
net unit
Output
trim
(8.5)
Empty
pipe
detection
(7.21)
Message
Software
seal
HART
Mass
ow URV
Vol ow
URV
Density
URV
Tempera-
ture
URV
Analog 1
high
LMT
Analog 2
high
LMT
Pulse 1
rate
Pulse 2
rate
QV is
Total
volume
unit
Lan-
guage
Autozero
(7.24)
Slug
detection
(7.20)
Descrip-
tor
Master
reset
New
Password
HART
Mass ow
LRV
Vol ow
LRV
Density
LRV
Tempera-
ture
LRV
Analog 1
low
LMT
Analog 2
low
LMT
Pulse 1
unit
Pulse 2
unit
TV is
Total
mass unit
Dips.
period
Zero ad-
justment
(5.6)
Net ow
(7.19)
Sensor
S/N
Long Tag
Num resp
preams
Enable wrt
10min.
HART
Mass ow
format
Vol ow
format
Density
format
Tempera-
ture
format
Analog 1
alarm
out
Analog 2
alarm
out
Pulse 1
select
Pulse 2
select
SI active
mode
SV is
Total ex
unit
Disp.
contrast
Input/
Output Test
(8.4)
Concentra-
tion meas-
urement
(7.18)
Sensor
constants
Tag
Num req
preams
Write
Protect
HART
Mass
ow unit
Vol ow
unit
Density
unit
Temper-
ature
unit
Velocity
unit
Analog 1
select
Analog 2
select
Pulse/
Stat 1
select
Pulse/
Stat 2
select
SI
function
PV is
Total ex
select
Display
select
Self test/
status
(8.3)
Flow
direction
(7.17)
Sensor
model
Distribu-
tor
Poll
address