Owner manual

3-20
IM 04L41B01-17E
• For parameters p7, p8, and p9, either set all
three parameters or omit all three parameters.
When Setting Channels to Square Root
Computation
Syntax
SR p1,p2,p3,p4,p5,p6,p7,p8,p9,p10,
p11<terminator>
p1
Measurement channel number
p2
Setting type (SQR
T)
p3
Measurement range
p4
Span lower limit
p5
Span upper limit
p6
Scaling lower limit (-30000 to 30000)
p7
Scaling upper limit (-30000 to 30000)
p8
Scaling decimal place (0 to 4)
p9
Unit (up to 6 characters)
p10
Low-cut function (OFF, ON)
p11
Low-cut point (0 to 50)
Query
SR[p1]?
Example
Convert the DC voltage measured on channel
001 to an amount of flow using the square root
computation. Set the measurement range to 6 V,
the span lower limit to 1 V, the span upper limit to
5 V, the scaling lower limit to 10.0 m
3
/s, and the
scaling upper limit to 100.0 m
3
/s.
SR001,SQRT,6V,1000,5000,100,1000,1,
m3/s
Description
•
Y
ou cannot use this command while recording
(memory sampling) or computation is in
progress. When using the /BT2 multi batch
option, you cannot use this command if any
of the batch groups is recording (memory
sampling).
•
Set p1 and p3 by referring to the table in
section 3.3.
• For parameters p4 and p5, enter values with
five digits or less excluding the decimal point.
• For parameters p6, p7, and p8, either set all
three parameters or omit all three parameters.
For 1-5V DC Voltage Input
Syntax
SR p1,p2,p3,p4,p5,p6,p7,p8,p9,p10
<terminator>
p1
Measurement channel number
p2
Input type (1-5V)
p3
Measurement range (1-5V)
p4
Span lower limit (800 to 5200)
p5
Span upper limit (800 to 5200)
p6
Scaling lower limit (-30000 to 30000)
p7
Scaling upper limit (-30000 to 30000)
p8
Scaling decimal place (0 to 4)
p9
Unit (up to 6 characters)
p10
Low-cut function (ON, OFF)
Query
SR[p1]?
Example
Set the channel 005 input type to 1-5V
, the span
lower limit to 1 V
, the span upper limit to 5 V, and
turn the 1-5V low-cut function ON.
SR005,1-5V,1-5V,1000,5000,,,,,ON
Description • You cannot use this command while recording
(memory sampling) or computation is in
progress. When using the /BT2 multi batch
option, you cannot use this command if any
of the batch groups is recording (memory
sampling).
• Set p1 by referring to the table in section 3.3.
• For parameters p4 and p5, enter values with
four digits or less excluding the decimal point.
• For parameters p6, p7, and p8, either set all
three parameters or omit all three parameters.
SO Sets a computing equation
Syntax
SO p1,p2,p3,p4,p5,p6,p7<terminator>
p1
Computation channel number
p2
Computation (ON, OFF)
p3
Computing equation (up to 120 characters)
p4
Span lower limit (-9999999 to 99999999)
p5
Span upper limit (-9999999 to 99999999)
p6
Span decimal place (0 to 4)
p7
Unit (up to 6 characters)
Query
SO[p1]?
Example
Compute the sum of channels 001 and 002
using channel 106. Set the span lower limit to
-10.0000, the span upper limit to 15.0000, and
the unit to V
.
SO106,ON,001+002,-100000,150000,4,V
Description
• Y
ou can use this command on models with the
/M1 or /PM1 math option.
•
Y
ou cannot use this command while recording
(memory sampling) or computation is in
progress. When using the /BT2 multi batch
option, you cannot use this command if any
of the batch groups is recording (memory
sampling).
•
For details on computing equations, see the
DX1000/DX1000N or DX2000 User’s Manual.
• Set p1 by referring to the table in section 3.3.
• For parameters p4 and p5, enter values with
seven digits or less, excluding the decimal, for
negative numbers and with eight digits or less
for positive numbers.
• For parameters p4, p5, and p6, either set all
three parameters or omit all three parameters.
ER Sets the range of an external
input channel
Syntax
ER p1,p2,p3,p4,p5,p6<terminator>
p1
External input channel number
p2
External input channel (ON, OFF)
p3
Span lower limit (-30000 to 30000)
p4
Span upper limit (-30000 to 30000)
p5
Decimal place (0 to 4)
p6
Unit (up to 6 characters)
Query
ER[p1]?
3.4 Setting Commands