User Manual

4-14
IM 04P01B01-17E
4.4 Setting Commands
VR Turns ON/OFF the recording on
each channel.
Dot model
Syntax
VR p1,p2,p3
<terminator>
p1
Channel number
p2
Trend recording ON/OFF (ON, OFF)
p3
Periodic printout ON/OFF (ON, OFF)
Query
VR[p1]?
Example Turn trend recording ON and turn periodic
printout OFF on channel 06.
VR06,ON,OFF
Description On models with the computation function (/M1
option), computation channels can be specified.
Pen model
Syntax
VR p1,p2
<terminator>
p1
Channel number
p2
Periodic printout ON/OFF (ON, OFF)
Query
VR[p1]?
Example Turn periodic printing ON on channel 01.
VR01,ON
Description
On models with the computation function (/M1
option), computation channels can be specified.
ST Sets the tag.
Syntax
ST p1,p2
<terminator>
p1
Channel number
p2
T
ag string (up to 7 characters)
Query
ST[p1]?
Example
Set the tag of channel 02 to
TI-2.
ST02,TI-2
Description
•
For the characters that can be used for the
tags, see appendix 1, “ASCII Character
Codes.”
•
On models with the computation function
(/M1 option), computation channels can be
specified.
SG Sets the message.
Syntax
SG p1,p2
<terminator>
p1
Message number (1 to 5)
p2
Message string (up to 16 characters)
Query
SG[p1]?
Example
Set character string “START” in message
number 1.
SG1,START
Description
For the characters that can be used for the
messages, see appendix 1, “ASCII Character
Codes.”
SE Sets the secondary chart speed
(used by the remote control
function (/R1 option)).
Syntax
SE p1
<terminator>
p1
Secondary chart speed
See the explanation.
Query
SE?
Example Set the chart speed to 50 mm/h.
SE50
Description
Select the chart speed from the list of choices
below
.
Pen model
5 to 12000 mm/h (82 levels, see section 4.3)
Dot model
1 to 1500 mm/h (1 mm steps)
SV Sets the moving average
(dot model).
Syntax
SV p1,p2
<terminator>
p1
Channel number
p2
Number of samples for computing the
moving average (OFF, 2 to 16) [times]
Query
SV[p1]?
Example Set the number of samples for computing the
moving average of channel 02 to 12.
SV02,12
Description
•
This setting is available on the dot model.
•
This setting is possible when moving average
is enabled (UI command).
SF Sets the input filter (pen model).
Syntax
SF p1,p2
<terminator>
p1
Channel number
p2
Filter time constant (OFF, 2s, 5s, 10s)
Query
SF[p1]?
Example Set the filter of channel 02 to 2 s.
SF02,2s
Description
This setting is possible when the input filter is
enabled (UJ command).
BD Sets the alarm delay time.
Syntax
BD p1,p2
<terminator>
p1
Channel number
p2
Alarm delay (1 to 3600) [s]
Query
BD[p1]?
Example Set the alarm delay of channel 01 to 120 s.
BD01,120
Description
•
This setting is possible when the alarm delay
function is enabled (UF command).
•
On models with the computation function
(/M1 option), computation channels can be
specified.
VF Sets the brightness of the display
(VFD) and internal illumination.
Syntax
VF p1,p2
<terminator>
p1
VFD brightness (1 to 8)
p2
Internal illumination (OFF, 1 to 4)
OFF
T
urns OFF the internal
illumination.
Query
VF?