Owner manual

ManualsBrandsYokogawa ManualsAir equipmentIntegral Oxygen Analyzer ZR202

100

Table Of Contents

Introduction
CONTENTS
1. Overview
- 1.1 < EXAxt ZR > System Configuration
- 1.2 < EXAxt ZR > System Components
  - 1.2.1 System Components
  - 1.2.2 Detectors and Accessories
2. Specifications
- 2.1 General Specifications
  - 2.1.1 Standard Specifications
- 2.2 General use Separate type Detector and Related Equipment
  - 2.2.1 ZR22G General use Separate type Detector
  - 2.2.2 ZO21R Probe Protector
- 2.3 Separate type Detector for High Temperature and Related Equipment
  - 2.3.1 ZR22G (0.15m) Separate type Detector for High Temperature
  - 2.3.2 ZO21P High Temperature Probe Adapter
- 2.4 ZR402G Separate type Converter
  - 2.4.1 Standard Specification
  - 2.4.2 Functions
- 2.5 ZA8F Flow Setting Unit and ZR40H Automatic Calibration Unit
  - 2.5.1 ZA8F Flow Setting Unit
  - 2.5.2 ZR40H Automatic Calibration Unit
- 2.6 ZO21S Standard Gas Unit
- 2.7 Other Equipments
3. Installation
- 3.1 Installation of General-purpose Detector
- 3.2 Installation of High Temperature Detector (ZR22G-015)
- 3.3 Installation of the ZR402G Converter
  - 3.3.1 Installation Location
  - 3.3.2 Mounting of the Converter
- 3.4 Installation of ZA8F Flow Setting Unit
  - 3.4.1 Installation Location
  - 3.4.2 Mounting of ZA8F Flow Setting Unit
- 3.5 Installation of ZR40H Automatic Calibration Unit
  - 3.5.1 Installation Location
  - 3.5.2 Mounting of ZR40H Automatic Calibration Unit
- 3.6 Installation of the Case Assembly(E7044KF)
  - 3.6.1 Installation Location
  - 3.6.2 Mounting
- 3.7 Insulation Resistance Test
4. Piping
- 4.1 Piping for System 1
- 4.2 Piping for System 2
- 4.3 Piping for System 3
  - 4.3.1 Blow Back Piping
- 4.4 Piping for the Detector with Pressure Compensation
5. Wiring
- 5.1 General
- 5.2 Wiring for Detector Output
- 5.3 Wiring for Power to Detector Heater
- 5.4 Wiring for Analog Output
  - 5.4.1 Cable Specifications
  - 5.4.2 Wiring Procedure
- 5.5 Power and Grounding Wiring
  - 5.5.1 Power Wiring
  - 5.5.2 Grounding Wiring
- 5.6 Contact Output Wiring
  - 5.6.1 Cable Specifications
  - 5.6.2 Wiring Procedure
- 5.7 Wiring for ZR40H Automatic Calibration Unit
  - 5.7.1 Cable Specifications
  - 5.7.2 Wiring Procedure
- 5.8 Contact Input Wiring
  - 5.8.1 Cable Specifications
  - 5.8.2 Wiring Procedure
6. Components
- 6.1 ZR22G Detector
  - 6.1.1 General-purpose Detector (except for ZR22G-015)
  - 6.1.2 High Temperature Detector (ZR22G-015)
- 6.2 ZR402G Converter
- 6.3 ZA8F Flow Setting Unit, ZR40H Automatic Calibration Unit
7. Startup
- 7.1 Checking Piping and Wiring Connections
- 7.2 Checking Valve Setup
- 7.3 Supplying Power to the Converter
- 7.4 Touchpanel Switch Operations
- 7.5 Confirmation of Converter Type Setting
- 7.6 Confirmation of Detector Type Setting
- 7.7 Selection of Sample Gas
- 7.8 Output Range Setting
  - 7.8.1 Minimum Current (4 mA) and Maximum Current (20 mA) Settings
- 7.9 Setting Display Item
- 7.10 Checking Current Loop
- 7.11 Checking Contact I/O
- 7.12 Calibration
  - 7.12.1 Calibration Setup
  - 7.12.2 Manual Calibration
8. Detailed Data Setting
- 8.1 Current Output Setting
- 8.2 Output Hold Setting
- 8.3 Oxygen Concentration Alarms Setting
- 8.4 Output Contact Setup
- 8.5 Input Contact Settings
- 8.6 Other Settings
9. Calibration
- 9.1 Calibration Briefs
- 9.2 Calibration Procedures
10. Other Functions
- 10.1 Display
- 10.2 Blow Back
  - 10.2.1 Blow back Setup
- 10.3 Parameter Initialization
- 10.4 Reset
- 10.5 Handling of the ZO21S Standard Gas Unit
- 10.6 Methods of Operating Valves in the ZA8F Flow Setting Unit
11. Inspection and Maintenance
- 11.1 Inspection and Maintenance of the Detector
- 11.2 Inspection and Maintenance of the Converter
- 11.3 Replacing Flowmeter in ZR40H Automatic Calibration Unit
12. Troubleshooting
- 12.1 Displays and Remedies When Errors Occur
  - 12.1.1 Error Types
  - 12.1.2 Remedies When an Error Occurs
- 12.2 Displays and Remedies When Alarms are Generated
  - 12.2.1 Alarm Types
  - 12.2.2 Remedies When Alarms are Generated
- 12.3 Countermeasures When Measured Value Shows Error
Customer Maintenance Parts List CMPL 11M12A01-02E
Customer Maintenance Parts List CMPL 11M12C01-01E
Customer Maintenance Parts List CMPL 11M12A01-11E
Customer Maintenance Parts List CMPL 11M03B01-10E
Customer Maintenance Parts List CMPL 11M03B01-05E
Customer Maintenance Parts List CMPL 11M03D01-01E
Revision Information

<7. Startup>

7-9

IM 11M12A01-02E

7.9 Setting Display Item

This section briey describes the display item settings shown in Figure 7.11, “Basic Panel

Display.”

F7.11E.ai

Tag:

21.0

%O2

17.43mA -Output1

17.43mA -Output2

Primary value

Secondary value

Tertiary value

Figure 7.11 Basic Panel Display

(1) Press the [Setup] key in the Basic panel display to display the Execution/Setup display.

Then select “Maintenance” in the Execution/Setup display.

(2) Select the “Display setup” from the Maintenance panel display (Figure 7.12).

The Display setup display (Figure 7.13) then appears.

(3) In the above Display setup display, select the “Display item”. The Display item display

(Figure 7.14) then appears. From this display, select the “Primary value” and press the

[Enter] key to display the “Display item” selection display (Figure 7.15).

(4) Select the Secondary and Tertiary values in the same manner as in the steps above.

(5) Consult Table 7.2, Display Items, enabling the selection of display items in individual display

areas.

Enter

Display setup

 Calibration setup

 Blow back setup

 mA-output loop check

 Contact check

Maintenance

F7.12.ai

Enter

Display item

 Trend graph

 Auto return time: 0min

 Language: English

Display setup

F7.13.ai

Figure 7.12 Maintenance Panel Display Figure 7.13 Display Setup

8th Edition : Jan.13,2012-00