Owner manual

ManualsBrandsYokogawa ManualsAir equipmentIntegral Oxygen Analyzer ZR202

121

122

123

124

125

126

127

128

129

130

Table Of Contents

Introduction
CONTENTS
1. Overview
- 1.1 < EXAxt ZR > System Configuration
- 1.2 < EXAxt ZR > System Components
  - 1.2.1 System Components
  - 1.2.2 Detectors and Accessories
2. Specifications
- 2.1 General Specifications
  - 2.1.1 Standard Specifications
- 2.2 General use Separate type Detector and Related Equipment
  - 2.2.1 ZR22G General use Separate type Detector
  - 2.2.2 ZO21R Probe Protector
- 2.3 Separate type Detector for High Temperature and Related Equipment
  - 2.3.1 ZR22G (0.15m) Separate type Detector for High Temperature
  - 2.3.2 ZO21P High Temperature Probe Adapter
- 2.4 ZR402G Separate type Converter
  - 2.4.1 Standard Specification
  - 2.4.2 Functions
- 2.5 ZA8F Flow Setting Unit and ZR40H Automatic Calibration Unit
  - 2.5.1 ZA8F Flow Setting Unit
  - 2.5.2 ZR40H Automatic Calibration Unit
- 2.6 ZO21S Standard Gas Unit
- 2.7 Other Equipments
3. Installation
- 3.1 Installation of General-purpose Detector
- 3.2 Installation of High Temperature Detector (ZR22G-015)
- 3.3 Installation of the ZR402G Converter
  - 3.3.1 Installation Location
  - 3.3.2 Mounting of the Converter
- 3.4 Installation of ZA8F Flow Setting Unit
  - 3.4.1 Installation Location
  - 3.4.2 Mounting of ZA8F Flow Setting Unit
- 3.5 Installation of ZR40H Automatic Calibration Unit
  - 3.5.1 Installation Location
  - 3.5.2 Mounting of ZR40H Automatic Calibration Unit
- 3.6 Installation of the Case Assembly(E7044KF)
  - 3.6.1 Installation Location
  - 3.6.2 Mounting
- 3.7 Insulation Resistance Test
4. Piping
- 4.1 Piping for System 1
- 4.2 Piping for System 2
- 4.3 Piping for System 3
  - 4.3.1 Blow Back Piping
- 4.4 Piping for the Detector with Pressure Compensation
5. Wiring
- 5.1 General
- 5.2 Wiring for Detector Output
- 5.3 Wiring for Power to Detector Heater
- 5.4 Wiring for Analog Output
  - 5.4.1 Cable Specifications
  - 5.4.2 Wiring Procedure
- 5.5 Power and Grounding Wiring
  - 5.5.1 Power Wiring
  - 5.5.2 Grounding Wiring
- 5.6 Contact Output Wiring
  - 5.6.1 Cable Specifications
  - 5.6.2 Wiring Procedure
- 5.7 Wiring for ZR40H Automatic Calibration Unit
  - 5.7.1 Cable Specifications
  - 5.7.2 Wiring Procedure
- 5.8 Contact Input Wiring
  - 5.8.1 Cable Specifications
  - 5.8.2 Wiring Procedure
6. Components
- 6.1 ZR22G Detector
  - 6.1.1 General-purpose Detector (except for ZR22G-015)
  - 6.1.2 High Temperature Detector (ZR22G-015)
- 6.2 ZR402G Converter
- 6.3 ZA8F Flow Setting Unit, ZR40H Automatic Calibration Unit
7. Startup
- 7.1 Checking Piping and Wiring Connections
- 7.2 Checking Valve Setup
- 7.3 Supplying Power to the Converter
- 7.4 Touchpanel Switch Operations
- 7.5 Confirmation of Converter Type Setting
- 7.6 Confirmation of Detector Type Setting
- 7.7 Selection of Sample Gas
- 7.8 Output Range Setting
  - 7.8.1 Minimum Current (4 mA) and Maximum Current (20 mA) Settings
- 7.9 Setting Display Item
- 7.10 Checking Current Loop
- 7.11 Checking Contact I/O
- 7.12 Calibration
  - 7.12.1 Calibration Setup
  - 7.12.2 Manual Calibration
8. Detailed Data Setting
- 8.1 Current Output Setting
- 8.2 Output Hold Setting
- 8.3 Oxygen Concentration Alarms Setting
- 8.4 Output Contact Setup
- 8.5 Input Contact Settings
- 8.6 Other Settings
9. Calibration
- 9.1 Calibration Briefs
- 9.2 Calibration Procedures
10. Other Functions
- 10.1 Display
- 10.2 Blow Back
  - 10.2.1 Blow back Setup
- 10.3 Parameter Initialization
- 10.4 Reset
- 10.5 Handling of the ZO21S Standard Gas Unit
- 10.6 Methods of Operating Valves in the ZA8F Flow Setting Unit
11. Inspection and Maintenance
- 11.1 Inspection and Maintenance of the Detector
- 11.2 Inspection and Maintenance of the Converter
- 11.3 Replacing Flowmeter in ZR40H Automatic Calibration Unit
12. Troubleshooting
- 12.1 Displays and Remedies When Errors Occur
  - 12.1.1 Error Types
  - 12.1.2 Remedies When an Error Occurs
- 12.2 Displays and Remedies When Alarms are Generated
  - 12.2.1 Alarm Types
  - 12.2.2 Remedies When Alarms are Generated
- 12.3 Countermeasures When Measured Value Shows Error
Customer Maintenance Parts List CMPL 11M12A01-02E
Customer Maintenance Parts List CMPL 11M12C01-01E
Customer Maintenance Parts List CMPL 11M12A01-11E
Customer Maintenance Parts List CMPL 11M03B01-10E
Customer Maintenance Parts List CMPL 11M03B01-05E
Customer Maintenance Parts List CMPL 11M03D01-01E
Revision Information

<8. Detailed Data Setting>

8-15

IM 11M12A01-02E

8.6 Other Settings

8.6.1 Setting the Date-and-Time

The following describe how to set the date-and-time. Automatic calibration or blow back works

following this setting.

Proceed as follows:

1) From the Basic panel display if you touch the [Setup] key, the Execution/Setup display

appears.

2) Select “Commissioning” and the Commissioning display appears.

3) Select “Others” and the display of Fig 8.12 appears.

4) Select “Clock” and the display of Fig 8.13 appears.

5) Select “Set date” and the numerical entry display appears. To enter June 21. 2004 , enter

210604. Touch the [Enter] key and you revert to the display of Fig 8.13.

6) Select “Set time”. Enter the time in 24-hour format. To set 2:30 pm, enter 1430 on the

numerical display and touch enter. Touch the [Enter] key. The clock starts from 00 seconds..

Clock

 Averaging

 Fuel setup

 Purging

 Unit setup

 Passwords

 Defaults

Enter

Others

F8.12E.ai

Enter

Set date: 1 3 / 0 7 / 0 0

 Set time: 1 4 : 3 9

1 3 J ul. 2 0 0 0

1 4 : 3 9 : 5 5

Clock

F8.13E.ai

Figure 8.12 Other Settings Figure 8.13 Clock Display

8.6.2 Setting Periods over which Average Values Are

Calculated and Periods over which Maximum and

Minimum Values Are Monitored

The equipment enables the display of oxygen concentration average values and maximum and

minimum values under measurement (see Section 10.1.1, later in this manual).

The following section describes how to set the periods over which oxygen concentration average

values are calculated and maximum and minimum values are monitored.

8.6.2.1 Procedure

1) From the Basic panel display touch [Setup] key, and the Execution/Setup display appears.

2) Select “Commissioning” and the Commissioning display appears.

3) Select “Others” then Averaging. The display of Fig. 8.14 appears.

4) Select “Set period over which average is calculated” and numerical entry display appears.

To set 3 hours, enter 003. Entry range is 1 to 255 hours.

5) Select “Set period over which maximum and minimum is stored” and numerical entry display

appears. To set 48 hours, enter 048. Entry range is 1 to 255 hours.

8th Edition : Jan.13,2012-00