User guide

6-13
IM DR231-11E
Commands
6
Example Do not create hourly reports and create daily and
monthly reports in standard format. Create the
monthly report at 10 O'clock on the first day of every
month and the daily report at 10 O'clock everyday.
ROOFF, ON1, ON1, 01 10
Comments • Effective only on instruments with the optional
report function.
• The report is output using TS4+device trigger
(GET)+RF.
• Date is set between 01 and 28 and hour is set
between 00 and 23 for p4.
RM Setting report channel to ON/OFF and
the report computation type
Mode Setup mode
Setting RMp1, p2, p3, p4, p5<terminator>
p1 Report channel number (R01 to R60)
p2 Set the report channel to ON/OFF.
p3 Corresponding channel number
Measurement channel: 001 to 060 for stand-
alone type, 001 to 560 for extended type
Computation channel: A01 to A30 for stand-
alone type, A01 to A60 for extended type
p4 The type of computation
INST Instantaneous value at the time when
the report is created.
AVE Average value
SUM Summed value
p5 Conversion of the standard unit of
time
INTVL No conversion
/sec Convert as the summed value of the
physical amount every second
/min Convert as the summed value of the
physical amount every minute
/hour Convert as the summed value of the
physical amount every hour
/day Convert as the summed value of the
physical amount everyday
Example Set the summed value of the measurement channel
005 which is measuring the amount of flow in units
of l/min to the report channel, R02.
RMR02, ON, 005, SUM, /min
Comments • Effective only on instruments with the optional
report function.
• If average value (AVE) is set on p4, minimum and
maximum values are also computed along with the
average value.
• If SUM is set on p4, the following computations
are carried out along with the summed value from
the time when the report was created to the next
report.
For hourly report: Total of the summed values up
to the time the daily report is created.
For daily report: Total of the summed values up to
the time the monthly report is created
Only summed value for monthly report
• The settings p3, p4 and p5 are effective when p2 is
ON.
• The setting p5 is effective only when p4 is set to
SUM.
• Since the sum is computed every measurement
interval using the sampled data, there are cases
when the physical amount per unit amount of time
is measured, the computed result differs from the
actual summed value (the measurement interval
and the unit time are different). In this case, set
the same unit used for the unit time of the physical
amount being measured to p5. The summed
values are computed using the following
converting equations depending on the
parameters.
INTVL ∑(measured values)
/sec ∑(measured values) x measurement
interval
/min ∑(measured values) x measurement
interval/60
/hour ∑(measured values) x measurement
interval/3600
/day ∑(measured values) x measurement
interval/86400
The unit of the measurement interval is seconds.
RI Setting the automatic print at the time
when the report is created to ON/OFF
Mode Setup mode
Setting RIp1<terminator>
p1 ON Print the report automatically at the
time when the report is created.
OFF Do not print the report at the time
when the report is created.
Example Print the report at the time when the report is created.
RION
Comments • This command is effective only with optional
report function.
• If a report is being printed from the FUNC menu
of the main unit or from the RP command,
automatic printing does not take place at the time
when the report is created..
SW Set the summer-winter time
Mode Operation mode
Setting SWp1,p2<terminator>
p1 Summer time or Winter time
SUMMER Summer time
WINTER Winter time
p2 Changing time
Example Change to summer time at 12clock 15th June 1996
SWSUMMER,96/06/15 12
XK Sets the key lock.
Mode Setup mode
Setting XKp1, p2, p3, p4, p5, p6, p7, p8<terminator>
p1 USE Uses the key lock.
NOT Does not use the key lock.
p2 RECORD key (LOCK, FREE)
p3 FEED key (LOCK, FREE)
p4 PRINT key (LOCK, FREE)
p5 FUNC key (LOCK, FREE)
p6 P.FUNC1 key (LOCK, FREE)
p7 P.FUNC2 key (LOCK, FREE)
p8 Pass number (0 to 9999)
Example Lock the RECORD, FEED, PRINT keys and set the
password number to 123.
XKUSE, LOCK, LOCK, LOCK, FREE, FREE,
FREE, 123
XF Sets the function to be displayed on
the function screen.
Mode Setup mode
Setting XFp1, p2<terminator>
p1 Content to be displayed on the function
screen.
ALARM_ACK
Acknowledgment of current alarm status
ALARM_RESET
Alarm is reset.
TIMER_RESET
Timer is reset.
6.5 Other Settings