User guide

ManualsBrandsYokogawa ManualsSensorsData Acquisition with PID Control CX2000

IM 04L31A01-02E

#7 Program control related (only when program control is ON)

<#1 Program parameter setting>

Parameter Selectable Range or Selections Initial Value

#1 Pattern initial setting

Program initial setting > Pattern number 1 to 4 (/PG1), 1 to 30 (/PG2) 1

Program initial setting > Segments 0 to 99 0

Program initial setting > Segment setting method Time, Ramp Time

Program initial setting > Pattern name Up to 16 alphanumeric characters Pattern 1

Program initial setting > Action loop > Loop 1 to 6 On/Off Off

#2 Wait action setting

Wait action setting > Wait zone 1 to 5 > Loop 1 to 6 On/Off Off

> High, Low EUS (100.0%) of the measurement span 1 digit

Wait action setting > Wait time 00:00:00 to 99:59:59 00:00:00

#3 Pattern start setting

Pattern start setting > Start target setpoint > Loop 1 to 6 EU (0% to 100%) of the measurement span –200.0

Pattern start setting > Start code StartTargetSP, RampPV1 to RampPV6, TimePV, StartTargetSP

#4 Program pattern setting

Program pattern setting > Segment number 1 to specified number of segments 1

Program pattern setting > Ramp/Soak select Ramp, Soak Ramp

Program pattern setting > Target setpoint > Loop 1 to 6 EU (0% to 100%) of the measurement span –200.0

Program pattern setting > Segment time

00:00:00 to 99:59:59 00:00:01

Program pattern setting > Ramp-rate time unit

Hour, Minute Hour

Program pattern setting > Ramp

1 digit to EUS (100.0%) of the measurement span 1 digit

Program pattern setting > Segment PID group No. 1 to specified PID number 1

Program pattern setting > Segment shift action Continue, HoldShift, LocalShift, ResetShift Continue

Program pattern setting > Wait action Off, Shift, Within Off

Program pattern setting > Wait zone number 1 to 5 1

#5 Event setting

Event setting > Segment number 1 to specified number of segments 1

Event setting > Event kind PVEvent, TimeEvent TimeEvent

Event setting > TimeEvent 1 to 16 On1, On2, On3, Off Off

Event setting > TimeEvent 1 to 16 > On-time, Off-time 00:00:00 to 99:59:59 00:00:00

Event setting > PVEvent 1 to 16 > Loop Off, 1 to 6 Off

Event setting > PVEvent 1 to 16 > Loop > Type PV-High, PV-Low, Deviation-High, Deviation-Low, Deviation-H&L, PV-High

Dev-within-H6L, SP-High, SP-Low, Output-High, Output-Low

Event setting > PVEvent 1 to 16 > Loop > Value PV: EU (0% to 100%) of the measurement span 1370.0

Deviation: EUS (0% to 100%) of the measurement span 1570.0

SP: EU (0% to 100%) of the measurement span 1370.0

Output: −5.0 % to 105.0 % 105.0 %

#6 Hysteresis (PV event)

Hysteresis (PV event) > PV event > Hysteresis 1 to 16 0.0% to 10.0 0.5%

#7 Repeat action setting

Repeat action setting > Repeat action Off, On, Repeat Off

Repeat action setting > On > Repeat frequency 1 to 999 1

Repeat action setting > Repeat action 1 to specified number of segments 1

> Repeat start segment

Repeat action setting > Repeat action 1 to specified number of segments 1

> Repeat end segment

When [Time] is specified for the segment setting method.

When [Ramp] is specified for the segment setting method.

<#2 Event output setting*>

Parameter Selectable Range or Selections Initial Value

Event output > Pattern number 1 to 4 (/PG1), 1 to 30 (/PG2) 1

Event output > Event kind PVEvent, TimeEvent TimeEvent

Event output > Relay Output EV1 to 16 On, Off Off

Event output > On EV1 to 16 > Number DO001 to DO006, DO101 to DO106, DO201 to DO206, DO001

RO001 to RO012, SW001 to SW036

Program pattern end signal > Relay Output On, Off Off

Program pattern end signal > On > Number DO001 to DO006, DO101 to DO106, DO201 to DO206, DO001

RO001 to RO012, SW001 to SW036

* With version 3.01, event output setting is included as item #6 within #1 Program pattern setting.

List of Parameters