User Manual

IM 01E20F12-01E
9-3
9. PARAMETER LISTS
9.2 AI Block Parameter List (Slot 1)
T0902-1.EPS
Index Parameter Valid Range Initial Value Description
Write
Mode
Information on this block such as Block Tag, DD Revision, Execution
Time etc.
The revision level of the static data associated with the function block.
The revision value will be incremented each time a static parameter
value in the block is changed.
The user description of the intended application of the block.
The strategy field can be used to identify grouping of blocks.
This data is not checked or processed by the block.
The identification number of the plant unit. This information may be
used in the host for sorting alarms, etc.
16 –BLOCK_OBJECT
17 – 0ST_REV
18 AutoTAG_DESC
19 Auto 00 to 65535STRATEGY
20 Auto 00 to 255ALERT_KEY
Set the Target of block mode (MODE_BLK) to Auto or O/S according
to the Write Mode of the parameter to be set or changed.
The mode parameter is a structured parameter composed of the
actual mode, the normal mode and the permitted mode.
Actual: Indicates the current operating condition.
Permit: Indicates the operating condition that the block is allowed
to take.
Normal: Indicates the operating condition that the block will usually
take.
21
22
Auto Auto
–ActualMODE_
BLK
(DS-37)
Auto
The current alert status, unacknowledged status, unreported status
and disabled status of the alarms associated with the function block.
23 –CurrentALARM_
SUM
(DS-42)
24 BATCH
(DS-67)
25 Not used
0
for future use
–Unacknowledged 0
for future use
–Unreported 0
for future use
–Disabled 0
This parameter is intended to be used in Batch applications in line
with IEC 61512.
AutoBATCH_ID 0
26 OUT
(DS-33)
This parameter contains the current measurement value from
Transducer Block or configuration adjusted engineering unit and the
belonging state in AUTO MODE.
OUT contains the value and status set by an operator in MAN MODE.
ManValue 0
27 PV_
SCALE
Conversion of the Process Variable into percent using the high and
low scale values.
The engineering unit of PV_SCALE high and low scale values are
direct related to the PRIMARY_VALUE_UNIT of the configured
Transducer Block (configured via Channel parameter).
The PV_SCALE high and low scale values follow the changes of the
PRIMARY_VALUE_UNIT of the related Transducer Block
automatically, i.e. a change of the Transducer Block PRIMARY_
VALUE_Unit causes no bump at OUT from AI.
O/S 0.00001 to 32000
or
0
0.00001 to 32000
or
0
Array 1
O/S
1342: %, 1355:Ml/d
1522: Ml/h
1521: Ml/min , etc
Array 2
Specified at the
time of order
29 LIN_TYPE This parameter is used in order to select the type of linearization.O/S 0: no linearisation
250: Not used
251: None
0
28 OUT_
SCALE
(DS-68)
Scale of the Process Variable.
This parameter contains the values of the lower limit and upper limit
effective range, the code number of the engineering unit of Process
Variable and the number of digits on the right hand side of the
decimal point.
O/SEU at 100%
O/SEU at 0%
O/SUnits Index
Auto exclude
0, 1, 2, 3
O/SDecimal Point
Specified at the
time of order
Specified at the
time of order
ManStatus 0
0
0
4
AutoRUP 0
AutoOPERATION 0
AutoPHASE 0
–Permitted O/S, Man,
Auto
The permitted bit is
only available.
O/S bit, Man bit,
Auto bit
–Normal Auto
Permitted bit is
only available.
Bit1, 2, 3, 4, and
7 are available.
TARGET_MODE
30 CHANNEL
Reference to the active Transducer Block which provides the
measurement value to the Function Block.
31 Not used
O/S 273 273
32 PV_FTIME
Time constant of a single exponential filter for the PV, in seconds.
Auto more than 0sec 0.000