User Manual

IM 01E20F02-01E
6-4
Table 6.2 Status of each parameter in warning mode
Warning 80:Adhesion Wng Good (NC);
Maintenance
required, ok
Good (NC);
Maintenance
required, ok
Good (NC);
Maintenance
required, ok
Good (NC);
Maintenance
required, ok
81:Insu-Brk Wng
Good (NC);
Maintenance
required, ok
Good (NC);
Maintenance
required, ok
Good (NC);
Maintenance
required, ok
Good (NC);
Maintenance
required, ok
Good (NC);
Maintenance
required, ok
82:Auto Zero Wng
Uncertain;
Non specific,
ok
Uncertain;
Non specific,
ok
Uncertain;
Non specific,
ok
Uncertain;
Non specific,
ok
Uncertain;
Non specific,
ok
Uncertain;
Non specific,
ok
Uncertain;
Non specific,
ok
Uncertain;
Non specific,
ok
Uncertain;
Non specific,
ok
84:Disp Over Wng – – – – – ––– –
85:FLow Vel Over Uncertain;
Non specific,
Low/High limt.
Uncertain;
Non specific,
Low/High limt.
Uncertain;
Non specific,
Low/High limt.
Uncertain;
Non specific,
Low/High limt.
Uncertain;
Non specific,
Low/High limt.
Uncertain;
Non specific,
Low/High limt.
Uncertain;
Non specific,
Low/High limt.
Uncertain;
Non specific,
Low/High limt.
Uncertain;
Non specific,
Low/High limt.
140:Sim. Jmpr On –––– –––
141:PB Sim.
enabled (Note1)
–––– –––
142:TB VF Sim.
enabled (Note1)
–––– –––
143:AI Sim.
enabled (Note1)
Depend on
SIMULATE.Status
Depend on
SIMULATE.Status
Depend on
SIMULATE.Status
–––
––
90:Display Sw – – – – – – –––
––
––
–– –
144:Total1 Sim.
enabled (Note1)
–––TOT1: Depend on
SIMULATE.
Status
TOT2: –
TOT3: –
–––
145:Total2 Sim.
enabled (Note1)
–––TOT1: –
TOT2: Depend on
SIMULATE.
Status
TOT3: –
–––
146:Total3 Sim.
enabled (Note1)
–––TOT1: –
TOT2: –
TOT3: Depend on
SIMULATE.
Status
TOT1: Depend on
SIMULATE.
Status
TOT2: –
TOT3: –
TOT1: –
TOT2: Depend on
SIMULATE.
Status
TOT3: –
TOT1: –
TOT2: –
TOT3: Depend on
SIMULATE.
Status
TOT1: Depend on
SIMULATE.
Status
TOT2: –
TOT3: –
TOT1: –
TOT2: Depend on
SIMULATE.
Status
TOT3: –
TOT1: –
TOT2: –
TOT3: Depend on
SIMULATE.
Status
–––
147:DI1 Sim.
enabled (Note1)
–––– DI1: Depend on
SIMULATE.
Status
DI2: –
DI1: Depend on
SIMULATE.
Status
DI2: –
DI1: Depend on
SIMULATE.
Status
DI2: –
148:DI2 Sim.
enabled (Note1)
–––– DI1: –
DI2: Depend on
SIMULATE.
Status
DI1: –
DI2: Depend on
SIMULATE.
Status
DI1: –
DI2: Depend on
SIMULATE.
Status
150:AI FB Man
Mode
–––– –––
151:Total1 FB Man
Mode
–––– –––
152:Total2 FB Man
Mode
–––– –––
153:Total3 FB Man
Mode
–––– –––
154:DI1 FB Man
Mode
–––– –––
155:DI2 FB Man
Mode
Note1: Make it the condition that the hardware simulation
j
umper is ON.
–––
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–– –––
Category Warning
FSAFE_TYPE = 0
AI Block
FSAFE_TYPE = 1 FSAFE_TYPE = 2 FAIL_TOT = 0 FAIL_TOT = 1 FAIL_TOT = 2
TOT Block
FSAFE_TYPE = 0
DI Block
FSAFE_TYPE = 1 FSAFE_TYPE = 2