User's Manual
P.2/4IM 01W06E01-01EN
3. Component Names
F02.ai
Strap hole
Nameplate
Case
Base
M4 screw
Slit
Hexagon socket screw or Conversion screw
Figure3.1 Component Names
Battery connector
Battery holder
Battery
X-axis
Y-axis
Z-axis
NFC
( marking)
Measurement axis indicator
4. Installation
4.1 Precautions
• For information on the ambient conditions allowed at the installation location, refer to
subsection 2.4 “Selecting the Installation Location”.
• Make sure that there are no damages,deformations, or stains adhering to the surface
of the Base. Any deformations or stains may affect measurements.
• To align the X-axis or Y-axis to the desired orientation, make appropriate adjustments
using the software after mounting. For details, refer to “IM 01W06E01-11EN”.
4.2 Installation Procedure
This product can be attached using two methods: direct mounting or using the magnetic
holder (F9096DA) included as an accessory.
To install XS770A, follow the procedure below.
1. Determine the mounting position of this product. Find a plain surface with a diameter
of 40 mm (1.57 inch) or more and a thickness of 6 mm (0.24 inch) or more.
2. Mounting this product.
2a. Direct mounting
2a.1 Follow the procedure below, make a vertical installation hole.
• In case using the hexagon socket set screw, make a screw hole (more
than 6 mm deep at M6 P-1) in the mounting position.
• In case using the conversion screw, make a vertical screw hole (more
than 0.24 inch deep at UNF1/4-28) in the mounting position.
2a.2 Attach the screw (provided hexagon socket set screw or provided
conversion screw) to the base. If using the conversion screw, screw the M6
side(with no notch) into the base.
2a.3 Attach this product to the installation hole made on the measurement
target, and tighten the screw using a tool such as a 46 mm wrench.
(Recommended tightening torque: 5.1 N·m)
2b. Using the magnetic holder
2b.1 Attach the provided hexagon socket set screw to the Base.
2b.2 Attach this product to the magnetic holder and tighten the screw using a
tool such as a 46 mm wrench or strap wrench. (Recommended tightening
torque: 5.1 N·m)
2b.3 Attach this product to the installation surface. The magnetic holder has a
strong magnetic force. When attaching, place the edge of the magnetic
holder on the installation surface once, then carefully install the product
without moving your hand.
3. Make sure that there is no loose space in the connection surface between this
product and the measurement target, and that no abnormal vibration occurs.
4. Conrm safety and tie the strap hole of this product to a structural object nearby with
a string as needed.
Removal is the reverse of the above.
CAUTION
• Tighten the screw and use the proper tools for all operations and ensure that the
tool is applied to the Base (metallic part).
• Install XS770A with extremely careful not to injure your hand or nger.
• Note that, when installing XS770A using the magnetic holder, the vibration
measurement frequency band drops.
• The magnetic holder can be mounted on ferrous material with a plain surface and
no painting. When installing other conditions of the above, tie the strap hole of this
product to a structural object nearby with a string*
1
and take measures to prevent
falling.
• In case the earthing of the Base (metallic part of the enclosure) is not ensured
by installation, use the screw at the side of the Base for bonding the Base to the
earth point or the equipotential bonding system.
*1: Use a wire with a load capacity (cutting load) of 2 kg or more.
5. Operation
To perform the setting and status check of the product, use an Android device with the
NFC interface. Download Sushi Sensor App from Google Play.
Sushi Sensor App provides the following functions.
• Network setting
• Sensor setting
• Status check of communication, sensor, battery life, etc.
• Switch to OFF Mode
For details, refer to “IM 01W06E01-11EN”.
Check the rmware version of XS770A with Sushi Sensor App and update it to the latest
rmware before use.
6. Maintenance
6.1 Replacing the Battery
Preparation
Only the dedicated battery specied by us should be used with this product.
When a replacement battery is needed, please order the XS70BT. The XS70BT is a set of
a dedicated product (model: LS14500 C5SY) with a battery connector assembled to the
SAFT battery.
CAUTION
Be sure to use a battery that is indicated as “Rev.1” for explosion protected
instruments
F03.ai
Replacing the Battery
WARNING
• Do not open when an explosive atmosphere is present.
• Use only battery LS14500 C5SY (SAFT)
• Be sure to replace the battery in a safe location. Doing so in an explosive area
could cause an explosion.
To replace a battery, follow the procedure described below.
IMPORTANT
• This product contains parts that can be damaged by static electricity. When
replacing a battery, take precautions such as using a grounded wrist strap to
avoid handling electronic parts or touching the board circuit patterns.
• When putting on or removing the Case, pay great attention to the environmental
conditions to prevent dust and water droplets entering the product.
• When replacing the battery, check that the product has sufciently cooled
because the built-in battery or internal components may still be hot.
• Be extremely careful not to apply excessive force to the circuit board, hit it with a
tool or allow any foreign materials or stains to adhere to it.
• Be extremely careful not to forcibly pull the cable in a way that may lead to
damage or disconnection.
• Be extremely careful to ensure that no foreign materials get into or become
adhered to the battery connector of the product when the battery is being
removed.
1. Remove two M4 screws xing the Case.
2. Remove the Case by inserting a athead screwdriver into the slit.
3. Disconnect the battery connector from the board.
4. Remove the used battery from the battery holder.
5. Put a new battery into the battery holder with the negative side facing down.
6. Connect the battery connector to the board.
7. Put the case onto the base with directing the nameplate to the battery side.
8. Tighten the M4 screw to x the case. (Recommended tightening torque: 1.37 N·m)
9. Initialize the battery life using Sushi Sensor App.
For details about how to initialize the battery life, refer to “IM 01W06E01-11EN”.
NOTE
If the battery and Case are not placed in the correct orientation, the Case will not be
able to be closed.
6.2 Handling the Battery
This product uses one lithium thionyl chloride primary battery. A single battery contains
approximately 0.7 grams of lithium. Under normal conditions, the battery materials are
self-contained and are not reactive as long as the battery integrity is maintained. Care
should be taken to prevent thermal, electrical or mechanical damage. Battery should be
stored in a clean and dry area. For maximum battery life, storage temperature should not
exceed 40°C.
Use the dedicated battery shown in “6.1 Replacing the battery”.
WARNING
Handling the battery
The following precautions must be observed to safely and effectively use a battery
pack. Improper use may lead to uid leakage, excessive heat, ignition, or explosion.
• Never charge it.
• Do not short-circuit it.
• Do not disassemble, transform, or modify it.
• Do not heat it or throw it in a re.
• Do not soak it in fresh water or seawater.
CAUTION
Observe the following precautions for the safe disposal of battery.
• Do not incinerate the battery, and do not expose it to a high temperature of 100°C
or more. This may lead to uid leakage or explosion.
• Dispose of the battery according to lows and regulations.
Transportation of products containing a lithium battery:
This product contains a lithium battery. When transporting this product with the battery
installed, set this product to OFF mode to prevent the battery from draining. For details
about how to change to OFF mode, refer to “IM 01W06E01-11EN”. Transportation of
primary lithium batteries is restricted by regulations issued by the U.S. Department of
Transportation, the International Air Transport Association (IATA), the International Civil
Aviation Organization (ICAO), and the European Ground Transportation of Dangerous
Goods (ARD). It is the responsibility of the shipper to ensure compliance with these
and any other local requirements. Consult current regulations and requirements before
shipping.
How to replace and dispose of the battery:
This is an explanation about the EU Battery Directive. This directive is only valid in the
EU.
The battery is included in this product.
When you remove the battery from this product and dispose of them,discard them in
accordance with domestic law concerning disposal.
Take the right action on waste batteries,because the collection system in the EU on waste
batteries are regulated.
Battery type: Primary lithium-thionyl chloride battery
Notice
The symbol (see above) means they shall be sorted out and collected as ordained in the
EU Battery Directive.
How to remove battery safely:
Refer to subsection 6.1 “Replacing the Battery”.
7. General Specications
7.1 Specications
Please refer to “GS 01W06E01-01EN” for the latest information.
Wireless Specications
Communication Protocol:
LoRaWAN class A, EU868, AS923, US915
Modulation
LoRa modulation
Data Rate:
• Area code 2,4: 250 to 11000 bps
• Area code 3: Transmitter: 980 to 12500 bps, Receiver: 980 to 21900 bps
Frequency:
• Area code 2: 863 to 870 MHz*
*: This wireless frequency can be used throughout, Europe, although there are some restrictions in
Sweden and Greece.
• Area Code 3: 902 to 928 MHz*
*: Available frequency bands vary depending on the country.
• Area code 4: 919 to 925 MHz*
*: Available frequency bands vary depending on the country.
Radio Security:
AES 128 bit encryption
RF Transmitter Power:
Max. 7 dBm
Antenna:
Built-in Omni-directional antenna
Power Supply Specications
Battery:
Lithium thionyl chloride battery: 1 unit (dedicated product)
Rated voltage: 3.6 V
Rated capacity: 2.6 Ah
Performance Specications
Item Specication
Vibration Measurement Acceleration (peak), Velocity (RMS)
Axis X, Y, Z axes and 3-axis composite
Range*
1
Acceleration: 0 to 130 m/s
2
(0 to 13.26 g)
Velocity*
2
: 0 to 20 mm/s (0 to 0.79 in/s)
Frequency range 10 to 1,000 Hz (± 3 dB)
Accuracy (100 Hz) X, Y, Z axes : ±10% FS
3-axis composite: ±20% FS
Temperature Measurement Temperature
Range -20 to 85°C (-4 to 185°F)
Resolution 0.1°C
Measurement part Base
*1: Peak value of the input vibration. For the relation between the measurement frequency band and
measurable range, refer to the following gure.
*2: The 20 mm/s pk value is equivalent to 14 mm/s RMS when input is based on a sine wave.