Specifications

六.软件功能software function
配对及解配Pairing and unmatching
同时按住遥控器的
和音量-
3 秒，遥控器清单配对信息，进入配对模式，配对过程中的红灯闪烁频率，
配对过程中红灯以2Hz
频率闪烁，
配对距离为
20
厘米到
1.5
米。如配对成功 ，遥控器红灯长亮
秒 ；如
30
秒后配对失败，
红灯熄灭。
设备名： ‘RC-27’
。工厂测试中，测试完毕后，测试软件会发出命令清除遥控器的配对信息。
At the same time, press and hold the remote controller for and 3 seconds, The remote
controller lists the pairing information, enters the pairing mode, and the flashing frequency of the red light in the
pairing process is 2Hz in the actual pairing process, and the pairing distance is 20 cm to 1.5 meters. If pairing is
successful, the redlight of the remote control stays on for 3 seconds; if pairing fails after 30 seconds, the red dot
goes out Equipment name: 'RC-27' during factory test, after the test is finished, the test software will issue a
command to clearthe pairing information of the remote controller.
6.2 回连Huilian
在 4米处遥控器与电视机保持连接至少 1 小时，不出现断连；在有配对信息并且蓝牙连接断开的情况下，
按"power键”和“配对组合键”不发回连广播。 其余任意键发送5秒回连广播，回连成功，指示灯闪3次.
Keep the remote control connected with the TV set at 4m for at least 1 hour without disconnection;
When there is pairing information and the Bluetooth connection is disconnected, Press the "power
key" and "pairing combination key" to not send the back connection broadcast. Any other key
sends the back connection broadcast for 5 seconds, the back connection is successful, and the
indicator flashes for 3 times
休眠及唤醒Sleep and wake up
未进行任何数据交互时，遥控器保持连接1小时后主动进入休眠断连状态， 按任意键可唤醒遥控器，
如还在连接状态，则发送对应按键的蓝牙码值；如已进入蓝牙连接断开状态，则进入回连状态，回连成功后，
按下任意键发送对应蓝牙码值；
Without any data interaction, the remote control keeps connected for 1 hour and then enters into the
state of sleep disconnection, press any key to wake up the remote control, if still connected, then
send thecorresponding key Bluetooth code value; If you have entered the Bluetooth connection
disconnect state, you willenter the backconnect state,After successful connection, Press any key to
send the corresponding Bluetooth code value;
在电视机开机启动时 ，检测遥控器升级文件， 若存在升级文件 ，遥控器进行 升级 ， 灯呈呼吸灯闪
烁。此时遥控器不可使用 ，任何按键无响应， 升级成功后 ， 灯停止闪烁 ，此时遥控器可正常使用 ，若升级失
败下次开机时再次检测并升级。 失败后 ， 灯停止闪烁 ，遥控器退回老版本正常运行。
When the TV is turned on, the upgrade file of the remote controller is detected. If the upgrade file exists, the remote
controller performs OTA upgrade, and the LED lamp flashes in breathing light Shuo. At this time, the remote controller can't
be used, and any buttons don't respond. After the upgrade is successful, the LED light stops flashing, and the remote
controller can be used normally at this time. If the upgrade fails, it will be detected and upgraded again at the next boot.
After OTA fails, the LED light stops flashing,and the remote controller returns to the old version for normal operation.
低电压提示
Low voltage prompt
电池电量低于 2.4V时，每次用户按键，则红灯闪烁3s， 频率1Hz
单载波测试
久按“
音量-
” ，遥控器进入单载波模式 ，发送频率为 2440MHz 、发送20秒 ，
功率为芯片最大功 率的单载波，松开
“音量
-”后退出单载波模式。
Press "volume" for a long time, and the remote control enters the single carrier mode. The transmission frequency is 2440mhz, the
transmission time is 20 seconds, and the power is the single carrier with the maximum power of the chip. Release "volume -" and exit the
single carrier mode.
指示灯状态 표시기 상태
按键
红外模式 Infrared mode
按键 Key 按键不亮灯 Keys do not light up
蓝牙模式 Bluetooth mode
Key
按键不亮灯 Keys do not light up
配对 Pair
配对 Pair
红灯闪烁
秒 ，频率
The red light ?ashes for 30
seconds at a frequency of 2Hz
配对成功 Pairing succeeded
红灯长亮 秒 The red light stays on for 3 seconds
配对失败 Pairing failed
红灯熄灭
The red light goes out
低电压状态
Lowvoltage state
按键 key
按任意键红灯闪烁 3 秒 ，频率
Press any key and the red light
flashes for 3 seconds at a
6.8
多按键不发码
Multi-key does not send code
不要求多按键不发
码
功能
.
Multi-key no-code function is not required.
freguency of 1 Hz
When the battery power is lower than 2.4V, Every time the user presses a key, Press any key, the red light flashes
for 3s, and the frequency is 1Hz