Specifications
Table Of Contents
- 说明书-KG-159
- 客户:
- PRODUCT INFORMATION AND REQUIREMENTS
- 按键工作的负荷力,按键平面中
- 使用规格
- 在温度55℃下搁置48小时,
- 在遥控器装有电池的条件下,
- 五.外观尺寸图/Dimension Drawing
- 六.软件功能software function
- 七.发码格式与波形/C O D E F O R MA T A N D W A V E
- 八.电气原理图 / E L E C T R I C A L S C H E M A T I C
- PCB 图 / PCB C H A R T
- 按键弹力测试 Push button elasticity test
- 十二、有害物质检测报告清单
- 十一 .遥控器(物料清单)/ R E M O T E C O
- 13.2. 包装外观检验 작업명세서의 중요설명:
- 箱面纸不许拼接、 缺材、露楞、折皱、透胶、
- FCC Statement警告语
WEATHERING
PERFO RM ANCE
跌落试验
Drop test
在遥控器装有电池的条件下,
不带包装,从80cm 高度自由
跌落在不小于3cm厚木板上,
遥控器的跌落面应与冲击面平
行,每个面(共6个面)各跌落
三次
Under the condition of remote
control with batteries, without
packing, free fall on a height
of 80 cm on the plank thicker
than 3cm, the fall of the
remote control surface should
be parallel to the strike face,
each side ( total 6sides) fell
three times
结构应无断裂,功能正常
The structure should be
faultless, all functions
should be normal
正常
normal
耐温水
Heat water
resistance
能耐60℃的温水, 60℃的温水
滴在遥控器表面三个不同的部
位上包括字符图形符号部位,
用软布擦干
It can withstand 60 degrees of
warm water, 60 degrees of
warm water dripping on the
surface of the remote control
three different parts including
characters and symbols, then
wipe with soft cloth.
遥控器的表面色调不起变化 ,字
符标志不被擦掉
The surface coltr of the
remote control should not
change, and character
marks should not be erased
.
正常
normal
字符、标志、涂饰部
分的附着力
The adhesion of
characters,signs,and
finishing parts
用粘附力为2‐3.5N/cm的透明
胶带粘遥控器的字符、标志和
涂饰部分
Use the adhesive tape with 2 to 3
5N/cm to stick the character,
logo and finishing part of the
remote controller.
3M胶纸粘贴,按压垂直拉起,
重复三次,无脱落现象
Paste with 3M adhesive tape,
press and pull vertically,repeat
three times. No falling off
正常
normal
耐溶剂性
Solvent resistance
1.用浸有20%的食盐水、无水乙
醇分别擦拭遥控器表面三个不
同部位上包括字符图形符号部
位30次
wipe three different part: on
the surface of the remote
control respectively with 20%
salt water and anhydrous
ethanol, including the symbol
parts of charactersand figures
30 times
2.将食用油用滴管滴在遥控器
表面三个不同部位包括字符图
形符号部位, 1h 后用软布擦
干
Drop the cooking oil into three
different parts on the surface
of the remote control,
including the characters and
symbols.Dry with a soft cloth
after Ih
95%酒精粘软布,500g重力垂直,
对丝印字符来回30次摩擦
表面硬度和外观无异常
字符图形符号清晰
95% alcohol adhesive soft
cloth, 500g gravity vertical, 30
times friction on silk screen
characters, no abnormal
surface hardness and
appearance, clear character
graphic symbols
LOGO> 100次 硅胶
黑色OK键>200次
其它硅胶丝印按键
>100次。合格
Logo > 100 times
filica black OK
key > 200 times,
ther silica sereen
printing keys>
100 times.
Qualified
,