User's Manual

●When the power is turned on, the blue indicator light is on
(off within 2 seconds), and it enters the standby mode;
●When the watch is charging, the blue light will turn on and off after 20 seconds;
●When the phone is charging, the blue light will turn on and off after 20 seconds;
●When charging the TWS headset, the blue light will turn on and off after
20 seconds;
●The light does not indicate when your device is fully charged
●When two devices are charging at the same time, the blue light indicates
that there are charging prompts on both sides
●When the wireless charger output is abnormally charged or foreign objects are
detected, the blue light keeps flashing.
M13
User Manual
Product input interface
Mobile phone/headphone charging position
Watch charging position
Indicator light
1
1
2
3
4
4
23
Dear customers, thank you for purchasing our products. In order to understand
the product further. Please read this manual carefully before use. We wish you
a pleasant experience!
Preface:
●Power connected ,the device enters the standby state;
●Place the Apple Watch in the Magetic charging area to conduct
wireless charging;
●Put the mobile phone that supports wireless charging on the
corresponding charging area for wireless charging.
Put the TWS headset that supports wireless charging on the
corresponding charging area for wireless charging.
Using instructions
Indicator light description
●Please confirm whether your mobile phone has wireless charging
function before use;
”Check whether the phone deviates from the wireless inductive
charging area of the charger;
‘Whether a non-metallic protective case is used for charging mobile
phones, and the thickness of the protective case is recommended
not to exceed 4mm;
When metal objects touch the charging area, the charger will
automatically identify and provide power off protection.
When the temperature of the charger is too high, it will automatically
start the protection.Please unplug the power supply first and use it
after the charger recovers the temperature.
How to solve abnormal charging:
Q:Why is there heating in the charging of wireless charging inductive
products?
A:During the charging process, there will be a certain loss of
magnetoelectric conversion, which will be converted into heat,
causing the mobile phone and charger to generate heat, which
is a normal phenomenon.
Suggestions:
●When the device is fully charged, disconnect it from charging in
time to avoid a long cycle of charging, which may lead to continuous
heating of the device and charger;
It is recommended to stop running the background software when
charging the phone.
●Use indoor or under dry environment, avoid placing or using in
the environment of high temperature, humidity, strong static
electricity and strong magnetic field;
For your safety, please do not use wet hand plug and unplug
electrical appliances;
. Avoid putting it in a place easily accessible to infants and children;
，Do not use the product if it is contaminated with water or dirt;
●Non-professional personnel are not allowed to open and repair
without authorization.
•iPhone13Pro Max/13por/13/13mini/12Por Max/12por/12/12mini/
• Apple Watch 7/6/SE/5/4/3/2
•Airpods/Third Generation/Pro/3/2
Compatible Devices
Input: 12V 1.5A
1: Phone output: 15W Max/Earphone output 3W Max
2: Watch: 3W Max
3.Input interface: USB-C
Specifications
Safety Notes
Q&A:
FCC Warning
Declaration of Conformity
IC Caution:
RF exposure statement:
Déclaration d'exposition RF:
Declaration of Conformityvv
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, This equipment
should be installed and operated with minimum distance between 20cm the
radiator your body: Use only the supplied antenna.
This device was tested for uncontrolled environment operations.
To comply with RF exposure requirements, a minimum separation
distance of 20cm must be maintained between the user’s body and the product.
Shenzhen Yifeng Intelligent Technology Co., Ltd.
The equipment complies with IC Radiation exposure limits set forth for
uncontrolled environments. This equipment should be installed and operated
with a minimum distance of 10cm between the radiator and your body.
Cet appareil contient des émetteurs / récepteurs exemptés de licence
conformes aux RSS (RSS) d'Innovation, Sciences et Développement
économique Canada. Le fonctionnement est soumis aux
deux conditions suivantes:
(1) Cet appareil ne doit pas causer d'interférences.
(2) Cet appareil doit accepter toutes les interférences, y compris celles
susceptibles de provoquer un fonctionnement indésirable de l'appareil.
L'équipement est conforme à la limite d'exposition aux radiations de la
IC établie pour un environnement non contrôlé. Cet équipement doit être
installé et utilisé avec une distance minimale de 10 cm entre
le radiateur et votre corps.
10th Floor, Building 2, Chaxi, Zone B, Huafeng First Science Park,
Hangcheng Street, Gushu, Baoan District, Shenzhen, China.
Radio Standards Specification RSS-Gen, issue 5
This device contains licence-exempt transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development Cana da’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
This device was tested for uncontrolled environment operations. To comply
with RF exposure requirements, a minimum separation distance of 20cm
must be maintained between the user’s body and the product.
Hereby, Shenzhen Yifeng Intelligent Technology Co., Ltd.declares that the
product type M13 is in compliance with Directives 2014/53/EU & 2011/65/EU.
The full text of the EU declaration of conformity is available at the
following internet address:https://www.YFZN.com/
Hereby, Shenzhen Yifeng Intelligent Technology Co., Ltd. declares that the
product type M13 is in compliance with following Regulations: Radio Equipment
Regulations 2017, Electrical Equipment (Safety) Regulations 2016 and The
Restriction of the Use of Certain Hazardous Substances in Electrical and
Electronic Equipment Regulations 2012. The full text of the UK declaration
of conformity is available at the following internet address:https://www.YFZN.com/
2-in-1 Magnetic Wireless Charging Pad
Radiated H-Field -17.8dBuA/m(@10m)
110-148kHz(Only for EU&UK)TX/RX Frequency Range
Radiated H-Field -24.24dBuA/m(@10m)
300-350kHzTX/RX Frequency Range
Radiated H-Field -17.8dBuA/m(@10m)
110-148kHz(Only for EU&UK)
115-205kHz(Only for FCC&IC)
TX/RX Frequency Range
Phone:
Watch: