ALL STEER MODEL 2000 HIGH CAPACITY CART OPERATOR’S MANUAL PART IDENTIFICATION 2565-726_REV_D 12/11 YETTER MANUFACTURING CO. FOUNDED 1930 Colchester, IL 62326-0358 Toll free: 800/447-5777 309/776-3222 (Fax) Website: www.yetterco.com E-mail: info@yetterco.
FOREWORD You’ve just joined an exclusive but rapidly growing club. For our part, we want to welcome you to the group and thank you for buying a Yetter product. We hope your new Yetter products will help you achieve both goals-increase your productivity and increase your efficiency so that you may generate more profit. This operator’s manual has been designed into four major sections: Foreword, Safety Precautions, Installation Instructions and Parts Breakdown.
SAFETY PRECAUTIONS You can make your farm a safer place to live and work if you observe the safety precautions given. Study these precautions carefully and insist those working with you and for you follow the precautions. Finally, remember this an accident is usually caused by someone’s carelessness, neglect or oversight. A brief description of signal words that may be used in this manual: CAUTION: Used as a general reminder of good safety practices or to direct attention to unsafe practices.
TABLE OF CONTENTS PAGE FORWARD/WARRANTY……………………………………………………….2 SAFETY INFORMATION……….………………………………………..……..3 TABLE OF CONTENTS……..….………………………………………..……..4 GENERAL INFORMATION/BOLT TORQUE…………………………..……..5 ASSEMBLY INSTRUCTIONS….…………………………………………….6-12 OPERATING/MAINTENANCE INSTRUCTIONS………………….……..13-15 PARTS IDENTIFICATION…………………………………………………..
GENERAL INFORMATION High capacity with high clearance keeps your planter and or side-dress operation running longer, the perfect answer for bigger, faster farming operation. The name of the game is to cover more acres each day and that is exactly what the 2000 Series All Steer High Capacity Cart accomplishes. What makes the All Steer High Capacity Cart unique is its tiretracking feature where the rear tires track the front tires at all times resulting in less compaction or less downed crops.
ASSEMBLY INSTRUCTIONS Step 1. Attach the axle stubs to the front and rear main axles using the ¾” X 2 ½” hex head bolts and locknuts. Step 2. Attach the hub/spindle assemblies to the axle stub, using the ¾” X 4 ½” hex head bolts and locknuts.
ASSEMBLY INSTRUCTIONS Step 3. Attach the tire/wheel assemblies to the 8-bolt hubs using the wheel nuts 2520-370. Torque to 100 ft/lbs.
ASSEMBLY INSTRUCTIONS Step 4. Insert the 2000-200 hitch drawbar tongue into the 2000-201 hitch receiver and install the ½” x 41/2” bolt and lock nut. Also at this time install the hitch pin and hair pin clip, pin the tongue in the retracted position. Install the 2570-178 jack onto the 2000-201 hitch receiver and secure with a pin and hair pin clip.
ASSEMBLY INSTRUCTIONS Step 5. Attach the drawbar assembly to the front axle using 2) 7/8” x 4” bolts and lock nuts.
ASSEMBLY INSTRUCTIONS Step 6A. Install light brackets to rear axle using ¾” x 7 x 7 u-bolt, and hex nut. Also, attach the red reflectors at the top of each light bracket as shown below. Step 6B.
ASSEMBLY INSTRUCTIONS Step 6C. I704-22 Step 7. Install lights to light brackets using hardware listed above.
ASSEMBLY INSTRUCTIONS Step 8. Install safety light wiring harness. Plumbing - No plumbing is supplied by Yetter Manufacturing Inc. Co. - SUGGESTION: Install a vent and overflow hose; plumbed to below the frame, in the event that the tank is overfilled, the product will not come in contact with the metal parts of the ALL STEER cart.
OPERATION DO NOT TOW THE ALL STEER OVER 25 MPH! THE TOW VEHICLE NEEDS TO BE ABLE TO SAFELY HANDLE A MINIMUM OF 24,000 LBS. Maximum carrying capacity of the ALL STEER model 2000 1600-gallon cart is 19,000 lbs. ▲CAUTION – Check for the 2565-495 SMV decal on the poly tank; if missing or illegible it must be replaced. Also, the safety decals need to be kept clean, visible, and legible. ▲CAUTION - Tighten nylon tie straps and replace if frayed. ▲CAUTION - Use safety chains and safety lights.
OPERATION FIELD LOCATION TRANSPORT LOCATION BE CERTAIN THE PINS ARE ENGAGED IN THE HOLES OF THE INNER STEERING LINK, AFTER CONVERTING FROM ALL STEER (4 WHEEL) TO TRANSPORT (2 WHEEL) STEERING OR WHEN CONVERTING FROM TRANSPORT (2 WHEEL) TO ALL STEER (4 WHEEL) STEERING. NOTE: SEVERE DAMAGE TO THE ALL STEER FERTILIZER CART OR ROLL-OVER CAN OCCUR.
LUBRICATION MAINTENANCE Check hub for bearing play yearly. Oil ball sockets to prevent corrosion, seizure and wear. Replace all worn bolts. Tire pressure 18.4 x 26-10 ply – Front 30 p.s.i. - Rear 30 p.s.i. CAUTION – Explosive separation of a tire and rim parts can cause serious injury of death. Do not attempt to mount a tire unless you have the proper equipment and experience to perform the job. Have it done by your implement dealer or a qualified repair service. Always maintain the correct tire pressure.
PARTS IDENTIFICATION 16
PARTS IDENTIFICATION MANUFACTURED 3-04 TO 6-04 17
PARTS IDENTIFICATION MANUFACTURED 3-04 TO 6-04 18
PARTS IDENTIFICATION MANUFACTURED 08-04 TO 08-05 19
PARTS IDENTIFICATION MANUFACTURED 08-04 TO 08-05 20
PARTS IDENTIFICATION MANUFACTURED 08-04 TO 08-05 21
PARTS IDENTIFICATION MANUFACTURED 08-04 TO 08-05 22
PARTS IDENTIFICATION MANUFACTURED 08-05 TO 07-07 23
PARTS IDENTIFICATION MANUFACTURED 08-05 TO 07-07 24
PARTS IDENTIFICATION MANUFACTURED 08-05 TO 07-07 25
PARTS IDENTIFICATION MANUFACTURED 08-05 TO 07-07 26
PARTS IDENTIFICATION REAR AXLE ASSEMBLY MANUFACTURED 03-04 TO 07-07 27
PARTS IDENTIFICATION FRONT AXLE ASSEMBLY MANUFACTURED 03-04 TO 07-07 28
PARTS IDENTIFICATION UPDATED 06/10/08 29
PARTS IDENTIFICATION 30
PARTS IDENTIFICATION MANUFACTURED 08-07 TO 01-08 31
PARTS IDENTIFICATION MANUFACTURED 08-07 TO 01-08 32
PARTS IDENTIFICATION MANUFACTURED 02-08 TO PRESENT 33
PARTS IDENTIFICATION MANUFACTURED 02-08 TO PRESENT 34
PARTS IDENTIFICATION MANUFACTURED 08-07 TO 01-08 35
PARTS IDENTIFICATION MANFACTURED 08-07 TO 01-08 36
PARTS IDENTIFICATION MANUFACTURED 02-08 TO PRESENT 37
PARTS IDENTIFICATION MANUFACTURED 02-08 TO PRESENT 38
PARTS IDENTIFICATION MANUFACTURED 08-07 TO PRESENT 39
PARTS IDENTIFICATION MANUFACTURED 08-07 TO PRESENT 40
PARTS IDENTIFICATION MANUFACTURED 08-07 TO 01-08 41
PARTS IDENTIFICATION MANUFACTURED 08-07 TO 01-08 42
PARTS IDENTIFICATION 2000-166 DET 1 2 3 4 5 6 7 QTY 1 1 1 1 1 1 1 PART NO.
PARTS IDENTIFICATION 12-09 TO PRESENT 44
PARTS IDENTIFICATION NOTE: THE LEFT FRONT STUB AXLE HAS THE AMBER REFLECTOR DECAL.
PARTS IDENTIFICATION 46
PARTS IDENTIFICATION NOTE: CAST HUB CANNOT BE ORDERED SEPARATE, ONLY ITEMS ASSEMBLED TO HUB CAN BE PURCHASED INDIVIDUALLY. PART NUMBERS LISTED UNDER 2000-322 ARE MANUFACTURES’ REPLACEMENT NUMBERS – NOT YETTER NUMBERS.
PARTS IDENTIFICATION 48
PARTS IDENTIFICATION UPDATED 02/2009 49
PARTS IDENTIFICATION 50
PARTS IDENTIFICATION 51
PARTS IDENTIFICATION 52
PARTS IDENTIFICATION 53
NOTES: 54
NOTES: 55
Our name Is getting known Just a few years ago, Yetter products were sold primarily to the Midwest only. Then we embarked on a program of expansion and moved into the East, the South, the West and now north into Canada. We’re even getting orders from as far away as Australia and Africa. So, when you buy Yetter products . . .you’re buying a name that’s recognized. A name that’s known and respected.
