Systems One A YETTER COMPANY SEED JET II 2565-441_REV_D 02/2012 YETTER MANUFACTURING CO. FOUNDED 1930 Colchester, IL 62326-0358 Toll free: 800/447-5777 309/776-3222 (Fax) Website: www.yetterco.com E-mail: info@yetterco.
FOREWORD You’ve just joined an exclusive but rapidly growing club. For our part, we want to welcome you to the group and thank you for buying a Yetter product. We hope your new Seed Jet II will help you achieve both increased productivity and increased efficiency so that you may generate more profit. This operator’s manual has been designed into four major sections: Foreword, Safety Precautions, Installation Instructions and Parts Breakdown.
TABLE OF CONTENTS Cover Page…………………………………………………………………….. 1 Foreword……………………………………………………………………….. 2 Table of Contents……………………………………………………………… 3 Safety Information……………………………………………………………... 4 General Information…………………………………………………………… 5 Assembly Instructions 1300-183 Power Unit Assembly……….……………………………...6 1300-120 Hopper Assembly……………………………………….… 7 1300-124 Seed Jet II Hose Assembly………………………………8-9 Operation………………………………………………………………………..10 Maintenance…………………………………………………………………….
SAFETY PRECAUTIONS You can make your farm a safer place to live and work if you observe the safety precautions given. Study these precautions carefully and insist those working with you and for you follow the precautions. Finally, remember this an accident is usually caused by someone’s carelessness, neglect or oversight. A brief description of signal words that may be used in this manual: CAUTION: Used as a general reminder of good safety practices or to direct attention to unsafe practices.
FAILURE TO HEED MAY RESULT IN PERSONAL INJURY OR DEATH. GENERAL INFORMATION SHIPMENT CHECKLIST Your Seed Jet II is shipped as a complete unit in one container.
ASSEMBLY INSTRUCTIONS POWER UNIT SET UP 1. Add oil to blower gear case. DO NOT OVERFILL. 8 oz., 80W-140 gear oil (ISO220, 5EP, GL-5 service grade). Lubricate the bearings using Shell Darina EP NLG grade 2 grease. 2. Fill crankcase of engine with oil. (High quality SAE 30 weight, SE, SF or SG service grade) 3. Fill gasoline tank with clean, fresh lead free gasoline (85 octane). NOTE: Engine Manufacturer does not recommend the use of gasoline, which contains alcohol such as gasohol.
ASSEMBLY INSTRUCTIONS HOPPER UNIT SET UP With the assistance of another person and/or lifting equipment, position the hopper assembly next to the discharge slide door of your gravity wagon. The hopper should be level once attached. The brackets supplied are of a universal type and it may be necessary to drill extra holes in the frame of your wagon to attach these parts. The long pins and spacers provided should accommodate most sizes of wagons.
ASSEMBLY INSTRUCTIONS 35’ SEED HOSE ASSEMBLY STEP 1. Attach the 1300-124 seed hose assembly to the 2 1/4” airlock fitting and secure with the 716 muffler style clamp. DO NOT OVER TIGHTEN THE CLAMP. 2570- STEP 2. Attach the 1300-166 cyclone exhaust kit to the seed cyclone. Left hand thread the 2515-712 hose cuff onto the 1300-553 3 1/8” OD vinyl hose. Then insert the hose and cuff assembly into the top of the cyclone.
ASSEMBLY INSTRUCTIONS STEP 3. Attach the 1300-163 cable assembly to the 1300-124 seed hose assembly. Connect the 1300163 cable to the power unit’s module at the plug connector labeled “switch input”. Inspect the plug connector for dirt, debris or bent pins; clean and repair the connectors if necessary. STEP 3. CONTINUED….Coil the cable assembly around the seed hose. Install the toggle switch to the cyclone handle and secure with the jam nut. STEP 4.
SYSTEM HOOK UP AND USE These instructions are to describe the typical set up of the Seed Jet II on a gravity flow wagon towed by a pickup truck. 1. Place power unit assembly in pickup bed and hitch truck to gravity wagon. 2. Assemble the rubber flex hose from the blower to inlet side of airlock using the quick coupler half provided and four hose clamps along with sufficient length of hose. Less hose will be required if the tailgate is lowered.
MAINTENANCE WARNING: Never clean, lubricate or adjust a machine that is in motion. Failure to heed may result in serious personal injury or death. 1. Inspect daily and clean safety decals. Replace if torn or no longer functional. 2. Inspect daily the air cleaner element and clean or replace as required. 3. Inspect daily and retighten, as required, all bolts on the power unit and assemblies. 4. Inspect daily and repair, as required, all air hoses and fittings. 5.
PARTS IDENTIFICATION 12
PARTS IDENTIFICATION 13
PARTS IDENTIFICATION 14
PARTS IDENTIFICATION 15
PARTS IDENTIFICATION PARTS IDENTIFICATION 16
PARTS IDENTIFICATION 17
PARTS IDENTIFICATION 18
PARTS IDENTIFICATION 19
PARTS IDENTIFICATION 20
PARTS IDENTIFICATION 21
PARTS IDENTIFICATION 22
PARTS IDENTIFICATION 1300-124 SEED JET II HOSE ASSEMBLY Key 1 2 3 4 5 6 7 8 9 Qty. 1 1 1 1 1 4 2 2 1 Part No. 1300-376 2570-721 2570-767 1300-596 1300-549 2502-105 2520-152 2515-711 1300-548 Description Cyclone, Black Hose Clamp, SAE #44, Ideal 64,SS 2” Conduit Hanger ZP w/Hardware 2-1/4” ID x 35 Ft. Cotton Lined S.S. Hose Cyclone Bracket 1/4-20 x 3/4 HHCS Gr.
PARTS IDENTIFICATION 24
POWER UNIT WIRING DIAGRAM DISCONNECT ALL WIRES AT NEGATIVE TERMINAL OF 12 VOLT BATTERY FOR SAFETY WHILE SERVICING UNIT.
TROUBLESHOOTING Problem Airlock will not turn on/off Airlock will not turn.
NOTES: 27
Our name Is getting known Just a few years ago, Yetter products were sold primarily to the Midwest only. Then we embarked on a program of expansion and moved into the East, the South, the West and now north into Canada. We’re even getting orders from as far away as Australia and Africa. So, when you buy Yetter products . . .you’re buying a name that’s recognized. A name that’s known and respected.
