owner’s manual 2012 yeti asr c YETI CYCLES 600 Corporate Circle, Unit D Golden, CO 80401 888.576.9384 www.yeticycles.
Table of Contents Brand Overview 06 Frame Features 08 Geometery 10 Maintenance Schedule 12 setup overview 14 Shock Setup rp23 15 Quick start guide rp23 16 Cable/Line Setup 18 technical Assembly Overview 20 chip system 23 Exploded Views 24 REBUILD KITS 26 legal 4. Warranty 28 Contact Information 29 5.
Welcome to the tribe. Congratulations on your purchase of a new Yeti. We are confident your new bicycle will exceed your expectations for value, performance, and ride quality. Each frameset and component has been custom specified and designed to enhance your riding experience. Whether you are a beginner cyclist, or a seasoned pro, your Yeti bicycle will provide endless hours of two-wheeled fun. This manual outlines basic setup and maintenance recommendations of your new Yeti.
everything about the asr carbon screams speed and efficiency. 8. 1. High modulus carbon fiber frameset 2. compatible with 100 or 120mm forks 3. press-fit bottom bracket 4. carbon dogbone 5. rear shock by fox racing shox 6. Dropouts 12mm x 142 thru axle or 135mm QR 7. custom chain-slap guards 1. The front and rear triangles are constructed entirely of high modulus, hand laid-up carbon with co-molded aluminum lugs at the bearing and pivot connections. 2.
Geometry 100 mm fork B I A J C D SM MD LG A 18.0 19.0 21.0 B 22.4 23.4 24.4 C 69.0 69.0 69.0 D 73.0 73.0 73.0 E 16.9 16.9 16.9 F 42.5 43.5 44.6 G 12.8 12.8 12.8 H 27.4 27.4 27.7 I 4.0 4.5 5.3 J 18.5 18.5 18.5 K 1.5 1.5 1.5 SM MD LG A 18.0 19.0 21.0 B 22.6 23.6 24.6 C 68.0 68.0 68.0 D 72.0 72.0 72.0 E 16.9 16.9 16.9 F 42.8 43.8 44.9 G 13.0 13.0 13.0 H 27.8 27.8 28.1 I 4.0 4.5 5.3 J 19.3 19.3 19.3 K 1.5 1.5 1.
keep your new yeti fresh and clean schedule ANNUALLY Yeti strongly recommends using a torque wrench when assembling your frame. Torque specifications for individual parts on the ASR-C are listed below, as well as in the step by step assembly instructions later in the manual. For general bicycle maintenance please consult the torque specifications of the manufacture’s component you are adjusting.
Shock Setup yeti tips tools needed Inspect your shock for any visible damage. If oil is leaking or you notice any damage to the surfaces or seals, please contact the Fox Racing Shox service center for repair at 800. FOX.SHOX. • Shock Pump • Tape Measue Shock set-up can fluctuate greatly based on the rider. The set-up guide is intended as a base line to get the rider started. Experiment with your settings to find the set-up that works best for you. 01. Air pressure rp23 02.
shock setup 04. rebound rp23 The rebound adjustment has 13 clicks of adjustment. The rebound knob is the red adjustment dial located above your blue pro-pedal adjustment lever. As a general rule, adjustments that are too fast (counterclockwise adjustment) will produce a springy ride with excessive kick-up of the rear end causing a bucking sensation. Adjustments that are too slow (clockwise adjustment) will cause packing of the rear wheel indicated by a sluggish ride feeling ride.
cable Setup yeti tips The ASRC has full cable housing. By using full cable housing, we have eliminated break points in the line of your shifter housing. This allows riders to experience better overall shifting performance by reducing the entrance of unwanted elements such as sweat and sediment. Use of full cable housing helps prevent corrosion from the elements and keeps the shifting smoother for a longer period of time.
Assembly yeti tips tools needed Make sure your tools are in good condition. A worn allen key can round the hex on a bolt not allowing for proper torque. • Dead blow hammer • Two - 5mm allen keys • Guide pin tool • Grease • Blue loctite Torque settings are listed throughout the instructions. It is also import to prep all bolt threads. The instructions denote whether to use a blue Loctite compound or grease. 01. 02. Press two 23.5mm reducers into the lower portion of the shock.
chip system assembly 05. 06. 01. 02. Slide the swingarm over the main pivot bore, using the grooves in the swingarm to properly align over the bore. Use the fox guide pin to align and hold the seatstays, dogbone, and shock together. Use a dead blow hammer to push the pin through the above mentioned components. Use a 2.5mm allen key to loosen the two M4x9mm flat head bolts holding the QR insert derailleur hanger in place. Remove the bolts and the QR insert from the frame.
Exploded Views 11 13 5 4 1 5 1 3 6 11 13 4 17 7 6 17 17 17 11 12 13 12 10 9 9 2 24 23 14 12 8 15 16 part # description qty na asr-c FRONT TRIANGLE 1 2 na asr-c SWINGARM 1 3 na fox rp23 [6.5”x1.5”] 1 4 300020020 GARLOCK DP BUSHING .5”.5” 2 5 300020034 REDUCER FOX 8X22MM 2 6 300020037 reducer fox 8x23.5mm 2 7 200020171 asr-c caRBON dogbone 1 8 300030188 PIVOT PIN 17X7.5/10X1THRD 52.
Rebuild Kits part # description qty 200020171 asr-c ‘08-’12 dogbone w/bearing 1 300020036 bearing 698max ext race 1.5 200020171 asr-c caRBON dogbone 200020137 200020138 26. 200020139 asr-c ‘08-’12 mounting hardware 1 4 300030062 WASHER 6.5X12.5X0.5 MM 3 1 300030069 WASHER 8.5X12.5X0.5 MM 3 300030190 BOLT-ti-FEMALE 8.0X40.5MM 1 asr-c ‘08-’12 bearing REBUILD KIT 1 300030111 BOLT-ti-FEMALE 8.0X34.0MM 1 300020001 bearing 6903 max 2 300030112 BOLT-TI-FEMALE 8.0X46.
Warranty Yeti Limited (1) ONE Year Frame Warranty (applies to 303 WC / 4X / DJ) Yeti Cycles will repair or replace, at its option, any frame it determines to be defective due to defective materials and/or workmanship. The (1) one year limited warranty is conditioned upon the bicycle being ridden under normal conditions and having been properly maintained.
