User Manual

ManualsBrandsYEP ManualsHobby7A (1~2S) Brushless Speed Controller 0.7g

SHENZHEN XINGQIONG TECHNOLOGY CO.,LTD

www.xqcontrol.com

ESC FOR AIRCRAFT AND HELICOPTER MANUAL

REV

2.0

Features

1. Equipped with high-speed, small-sized, multifunctional MCU.

2. Full protection feature including low-voltage protection, over-heat protection, signal lost protection, safe power

on protection, and self-check functions.

3. Excellent startup performance, great throttle linear and quick throttle response.

4. Excellent low-speed performance.

5. Max speed: 240,000 RPM (2 poles), 80,000 RPM (6 poles), 40,000 RPM (12 poles).

6. Individual power circuit for MCU and BEC to improve anti-interference capability.

7. Built-in linear BEC.

8. The parameters of ESC can be configured via program card or transmitter .

9. Program card is displayed by LCD panel, make setting conveniently and easily.

10. The low-voltage threshold and start-up power can be programmed quantized and precisely by program card.

11. Throttle range can be configured to be compatible with different receivers.

12. Three throttle curve options make helicopter control more flexible.

13. Configuring by transmitter, motor reverse rotation available.

Specification

Model

Continuous

Current

Burst current

(10S)

Li-XX

Size(mm)

L*W*H

Weiht

(g)

BEC

Linear

Program Function

XP-7A 7A 9A 1-2 22 12 5 5 1A YES

XP-12A 12A 15A 1-3 22 17 7 8 1A YES

XP-18A 18A 23A 2-3 45 24 6 18 2A YES

XP-25A 25A 30A 2-4 50 28 12 31 2A YES

XP-30A 30A 40A 2-4 50 28 12 34 2A YES

XP-35A 35A 45A 2-4 59 28 12 38 3A YES

XP-40A 40A 50A 2-5 58 28 11 35 3A YES

XP-50A 50A 65A 2-5 59 28 15 44 3A YES

XP-60A 60A 80A 2-5 63 28 18 51 3A YES

XP-80A 80A 100A 2-5 63 28 18 60 3A YES

XP-100A 100A 120A 3-6 96 55 21 130 N/A YES

XP-120A 120A 150A 3-6 96 55 21 150 N/A YES

XP-150A 150A 180A 3-6 96 55 21 180 N/A YES

XP-80A-HV 80A 100A 3-10 96 55 21 150 N/A YES

XP-100A-HV

100A 120A 3-10 96 55 21 160 N/A YES

XP-120A-HV

120A 150A 3-10 96 55 21 180 N/A YES

Max. load of Built-in Linear BEC 5V/3A

Li-xx Battery 2 cells 3 cells 4 cells 5 cells

Qty of standard servo (Max.) 5 5 4 3

Note: For ESC without built-in BEC, an UBEC or individual battery pack should be required to power

the receiver and servos.

Summary of content (5 pages)

PAGE 1
www.xqcontrol.com SHENZHEN XINGQIONG TECHNOLOGY CO.,LTD ESC FOR AIRCRAFT AND HELICOPTER MANUAL REV 2.0 Features 1. Equipped with high-speed, small-sized, multifunctional MCU. 2. Full protection feature including low-voltage protection, over-heat protection, signal lost protection, safe power on protection, and self-check functions. 3. Excellent startup performance, great throttle linear and quick throttle response. 4. Excellent low-speed performance. 5.
PAGE 2
www.xqcontrol.com SHENZHEN XINGQIONG TECHNOLOGY CO.,LTD Using ESC Normal Startup Procedure → → → → Move throttle stick to the bottom position (full Off throttle) Switch on the transmitter Connect battery pack to ESC System detects the Min throttle signal, makes a long “beep” sound System detects battery when self-test is voltage and makes several short “beep-” sounds, which denotes the number of battery cells finished ♪123 tone should be emitted ready for start.
PAGE 3
www.xqcontrol.com SHENZHEN XINGQIONG TECHNOLOGY CO.,LTD speed, the “High” timing mode is recommended. ．Start: Fast, Soft and Very Soft. default is Very Soft. Fast start is recommended for low inductance and low start loading motors, Very Soft start is recommended for high inductance and high start loading motors. 5．OffType(Cutoff Mode,Low Voltage Protection Mode): Reduce power and Cutoff output power for selecting, default is Reduce the output power gradually to 50% of the current power.
PAGE 4
www.xqcontrol.com SHENZHEN XINGQIONG TECHNOLOGY CO.,LTD Program ESC with transmitter 2.Select programmable items After entering program mode ,you will hear 9 tones in a loop in the following sequence. If you move the throttle stick to bottom within 2 seconds after one kind of tone, this item will be selected.
PAGE 5
SHENZHEN XINGQIONG TECHNOLOGY CO.,LTD www.xqcontrol.com Using program card Adopting 2x16 point LCD panel, program card can make all setting conveniently and directly. The keys function KEY FUNCTION WR To move the cursor horizontally To move the cursor vertically and change item or item value To confirm selected item or item value. To write and save setting parameter to ESC Program procedure 1. Unplug the battery of ESC and connect the PPM wire to program card properly. 2.