User Manual

ManualsBrandsYEP ManualsHobby18A (2~4S) SBEC Brushless Speed Controller

YEP 18A ESC

Specifications:

- Given current is the maximum continuous full executive power with adequate cooling

- 2 to 6S LiPo, with undervoltage protection.

- 6-18 NiMH cells, with undervoltage protection.

- The possibility of disconnection when detecting undervoltage

- SBEC Output: 5.5V, 3A permanent, 5A max

- Governor Mode

- Soft Start

- Active idle, allowing unlimited / partial load

- Automatic or 6x step adjustable timing

- Continuously adjustable (adjustable) F3A brake

- 3-step adjustable brake EMF

- Switching interval: 8 to 16kHz

- Speed limit: 240,000 RPM (2-pole motors)

- Temperature control and overload

- A circuit that prevents sparks: reduces sparking when connecting

- Programming with ProgCard II (the program card)

Initial setting:

After connecting the battery (red (red) = plus, black (black) = minus) you hear 3

descending tones. Then you hear a series of beeps, depending on the cell number of the

connected Lipo battery.

If the transmitter throttle stick is in the "off throttle”, you will hear 3 rising tones.

It is necessary to connect the motor to hear the beep, since the motor itself acts as a

speaker.

--- The controller is now ready for use ---

If the motor runs in the opposite direction, simply replace 2 of the 3 motor connectors.

Use only clean and solid gold connectors for motor and battery. PK 3.5-mm connectors are

the best choice from 30 to 80 A. Be careful to choose the correct polarity security system

battery connector. Replace sparking or corroded connectors. Because only if these are in

order and will have the correct contact, then they can ensure lasting leadership to prevent

regulator worked properly. If you type 120A and 160FAI please use 5.5 and / or 6 mm PK

gold connectors, 3,5 and 4 mm because connectors are verified (suitable) only to 80A.

Motor cables are usually truncated to a minimum and soldered exactly that seats on the

engine. On the other hand, all ESC types, the total length of the cable from the controller to

the battery should not exceed 20 cm. If need longer cables, Low ESR 330μF capacitor

switching / 25Vby should be every 20 cm soldered between plus and negative lead. It is

possible to consider using our capacitor type YGE Cap's fifth Similar cables signal can be

extended. In this case, please use twisted-pair cables to minimize jamming.

Note: The rollover polarity battery causing severe damage and void the warranty.

Summary of content (4 pages)

PAGE 1
YEP 18A ESC Specifications: - Given current is the maximum continuous full executive power with adequate cooling - 2 to 6S LiPo, with undervoltage protection. - 6-18 NiMH cells, with undervoltage protection. - The possibility of disconnection when detecting undervoltage - SBEC Output: 5.
PAGE 2
General settings: The controller has a fixed setting the throttle curve (throttel curve), so they are linearly linked to all conventional transmitter and drawers. With all programmable transmitters, "throttle range) should be set to the default (+ 100%), trim set to zero and the "throttle trim" ???? released. However, necessary with some transmitters that this area has been leveled.
PAGE 3
Brake off Act.Freew. he ??? P-Gain = 0.9 I-Gain = 0.05 Trigger Speed - heli middle PWM - Frequency = 8 kHz automatic startup power = 1-32% (sometimes it is better 2 or 4%) Adjust the default P-gain, I-gain and PWM frequency only when you reach required performance and if you are sure the correct settings for all other components (Components). Lipo protection / undervoltage protection: With a voltage controlled matched load is possible to fly further on less power until the battery manage with less stress.
PAGE 4
be connected to a separate receiver without any special precautions (use of parallel BEC). The total maximum load is the sum of the individual BEC. It is also possible configuration without BEC as galvanic isolation. For this, please use our opto coupler module. Please note: Mainly it is important to make sure that the propeller in circulation, there are no objects when the battery connected.