User Manual VHF Transceiver XP-100D UHF Transceiver XP-400D YeonHwa M Tech Co.
1. XP-100D/400D Series Main Features The XP-100D/400D Digital Radio was developed by YeonHwa M Tech Co.,Ltd to be user-friendly and compact design, to have various features and to use at the construction / industrial / commercial / public areas for the safety & convenience of users. It provides better communication distance, audio quality and volume, duration of use through digitalization than Analog radio. The followings are the main features of the XP-100D/400D Series Radio.
2. Specification 2.1 XP-100D General Frequency Range XP-100D :136 ~ 174 MHz XP-400D : 400~470 MHz Frequency Stability ±1.5ppm (-30 to +60 ) Programmable Channels 16 Zones / 32 Channels Channel Spacing 12.5KHz Digital Vocoder AMBE++ Dimensions 103mm(H) x 52mm(W) x 32mm(D) Weight 280g Power Source DC +7. V Li-ion 2,600mAH Battery Current Drain (maximum) Receive mode, rated audio out Transmit mode 1,200mA Standby mode 110mA 420 (Audio Max) Receiver Sensitivity 0.
3. Checking items in the package Components could be changed by buyer request.
3.
Figure 3-2) LCD Indication of XP-100D/400D Series Radio 4. Basic operation Please fully read the instruction manual before use. This manual provides important information related to radio operation. 4.1 Installation and Removing the Antenna To install the antenna, insert the antenna into antenna connector and screw the antenna clockwise. To remove the antenna, screw the antenna counter clockwise.
4.2 Installation and Removing the Battery 4.2.1 Installation of the battery To install battery, slide up the battery towards the top of the radio until battery latch is locked. 4.2.2 Removing the Battery - Slide the battery latch located on the bottom of radio to the open position as shown in Figure 4-2. The battery is removed by pressing it against and sliding it towards the bottom of the radio Figure 4-2) Installation and Removing the Battery 4.
4.4 Accessory connector Accessory connector is used to connect external speaker MIC, and headset, etc. Please close the cover when it is used. Figure 4-4) Accessory connector 5. Radio operation The definition of the various buttons of the XP-100D/400D series is the same as Figure 5-1).
5.1 Power ON/OFF, Volume Switch Turning the volume switch knob clockwise to power on and turning the knob counterclockwise to power off. And when set an audio volume level, please refer with the index on the side of the volume knob. 5.2 PTT Button Pressing PTT button, the radio mode is transmission and releasing the button, it is receiving mode. It is recommended to talk 5~10cm away from the microphone for the best voice communication. 5.
5.5 CH/Menu UP/Down Button "CH / MENU UP" and "CH / MENU Down" are to change channels and in the menu entry mode, it is select the UP / Down of the Menu. 5.6 EAR/MIC Jack Accessory connector is used to connect external speaker Mic, and headset, etc. Please close the cover when nothing is connected.
6. Charging the Battery 6.1 Safety Notes 1) The radio of XP-100D/400D series receives power from high-performance Li-ion battery (XL260). XL-260 Battery is safe of high performance and highly reliable, and could be charged very fast. The charging of the enclosed Radio on t cause damage on the battery and also, will cause a trouble on the Radio. 2) Please charge the battery before using the radio for best performance and safety.
6.4 Charger (XC-100/XC-200) The XC-100/XC-200 charger is designed to charge only the Li-ion battery enclosed in this Radio.
7. Using the XP-100D/400D Series 7.1 Menu description Press the Menu/OK button on the front to enter the menu mode. In the menu mode, there are eight of the main menus, and set and used according to the application and the environment, it can be more convenient to use. Figure 7-1) XP-100D/400D Menu Note) If the menu is not operated for at least 25 seconds after launch, the menu mode is automatically end and it is switch to receive mode. 7.1.
2) Inbox It is possible to store up to 10 incoming messages. When you choose contents stored in the list, you can see the received messages. When the received message is more than 10, the earliest incoming message is cleared first and it is registered. If you want to delete incoming messages, it can be deleted by selecting delete all menu. 3) Outbox It is possible to store up to 10 outgoing messages. When you choose contents stored in the list, you can see the outgoing messages.
7.1.5 Scan When turning ON the scan operation, to start the scan in the order of the channel that has been set in the scan list. If there is a channel used during the scan, you will receive the contents stops at that channel. If you want to call, you can use the settings to suit your needs by the CPS program. 1) Scan ON/OFF Select the scan settings or scan release at the scan of menu and go to receive mode.. 2) Scan list Scan list can be set using the CPS program. 7.1.
BCL: If the current channel is busy, the transmission prohibition BCLO: The ability to send regardless of the user of the current channel 6. Button Lock With the exception of the minimum of buttons necessary for the user to prevent unwanted terminal operation, it is the ability to limit the operation. When the button lock is on, all buttons are locked except the PTT button, the emergency button and power ON / OFF button. 7. Tones This is a Tone setting function. The main menu is available only ON / OFF.
8. Precautions 8.1 Matters affecting the performance of the equipment. e strong electronic wave to be emitted from the Radio can have an effect on the performance of the Radio and can cause the Radio to have a defect. speaker microphone and earphone, etc.) from the other makers, which can cause to make a defect on battery and a malfunction or a defect on the Radio. will be causes of defect or malfunction and it will be impossible to make repair afterward. Also, a punishment can be made by law.
In case of the area that medical equipments are being used, please use the Radio after discussion with the equipment maker or the related doctor. electric/electronic devices are being used, because the strong electronic wave from the Radio can have an effect on the equipments. 10. Safety Notes Please make sure to read the followings for safe and effective use of the Radio. skin. it may cause fire, explosion and burn. Especially, please be careful when putting the battery in a pocket or a bag.
Warranty Card Thank you for purchasing XP-100D/400D Series. 1. This product has passed strict quality control and testing process. 2. Warranty is one year from the day the factory. ng conditions, during the warranty period may be repaired by YeonHwa M Tech Co.,Ltd or our authorized service organization free of charge. 3. For the following cases, some service fees will be charged. performance failure, malfunction or damage. improper operation. or otherwise access to sealed/non-user serviceable items.
Output: DC12V,1A
