Instruction Manual

V10
Precautions
1.Do not leave this product in a high temperature and humid or rainy environment,
please use it in a ventilated and dry place;
2.Do not open the back cover, if you need to repair, please contact the after-sales personnel;
charger to charge both receiver
and transmitter.
3. This product does not include a charger in the packaging, please use a 5V 1A If you need to charge them during use, it is
recommended to use a mobile
4. This product is not waterproof, please ensure that the device should
power bank to avoid current noise; not be exposed to
Product specifications
1. Support single wireless mic receiver
--Working distance: 10m (32ft).
--Audio frequency: 35Hz~20KHz stereo 48K sampling rate.
--Delaying: 23ms.
--Continuous Working time: 7 hours (500mAh polymer battery).
--Low battery reminder and automatic shutdown.
Sound card panel introduction
Headph ones Audio Input
Microph one Live
Long press on/off
Short press mode switch
Long press to monitor +
short press to headphone microphone +
Long press to monitor -
short press to headphone microphone -
Steps to set up
-1- Connect the device with a live cable (Type-C OTG live cable/Lightning OTG live cable/3.5mm live cable);
-2- Long press the "power" button on the device to turn on
-3- Press and hold the power button of the lavalier microphone to turn it on, the indicator will flash after booting,
and the indicator will be always on after the device is successfully connected with phones or tablets.
Insert 3.5mm monitor headphones into the 3.5mm headphone jack on top of the microphone as needed:
-4- Use the buttons of the device or the wireless remote control to control the function and adjust the sound;
-5- Insert a 3.5mm wired headset to the transmitter for live broadcast or direct broadcast according to the needs
of live broadcast;
-6- Connect the accompaniment input via AUX or Bluetooth as needed.
water droplets or splashes.
Charging
Type - C
Product description
1. This is a wireless sound card microphone (Mini lavalier), two-way stereo low-latency wireless digital transmission,
48K sampling rate, high-quality audio;
--The wireless microphone supports stereo monitoring; please contact the after-sales team;
--Support Bluetooth and AUX accompaniment audio input;
2. Receive bluetooth stereo accompaniment from smartphones, tablets or laptops.
--Working distance: 8m (26ft).
--Bluetooth 4.2, support A2DP.
--Automatically connect to the last bluetooth device.
3. Automatically connect to the last bluetooth device.
--48K 16 bits high quality sampling.
Type-C
charging port
indicator light
OTG interface
3.5mm monitor earphone
(Can be connected via Bluetooth)
MADEINCHINA
--Support mobile phone live broadcast, support OTG digital stereo (requires mobile phone to support
Type-C interface and support OTG function);
--Suitable for live broadcast, shooting Vlog, teaching, speech, conference and other purposes;
--Can be connected to various smart phones, tablets, notebooks and other devices via Bluetooth;
--Support wireless remote control, extremely convenient to control;
--Built-in professional DSP sound processor for reverberation and mixing processing;
--The sound card in this device is powered by a built-in 600mAh lithium battery,
and the wireless microphone is powered by a built-in 500mAh lithium battery.
.01.
--Digital vocal reverb effect processing, 2 reverb modes.
--Monitor volume independent adjustment.
--Supports simultaneous input of Bluetooth and AUX accompaniment.
4. Special features
-- Support Wireless headset + wired headset dual live broadcasts.
-- Director mode: The sound of the director can only be monitored by the wireless microphone
and will not be live broadcated.
-- Support 8 special effect sound.
-- Support ducking function (microphone first, if the microphone has sound input,
the accompaniment will be automatically volume reduced)
.02.
Lavalier microphone panel introduction
Long press to turn on/off, short press to mute,
double click to switch sound mode.
Long press monitor +
short press microphone +
Long press monitor -
short press microphone -
.04.
3.5 mm
interface
microphone
Live cell phone
.05.
Accompaniment mobile phone
(Note: the picture is for reference only, please refer
to the actual product)
OTG
Headph ones Audio Input Micr ophone Liv e
OTG
Headph ones Audio Input Micr ophone Liv e
Product content
(Note: The picture is for reference only, please refer to the actual product)
Lavalier microphone *1
Transmitter *1 3.5mm audio live cable *1 3.5mm camera Type-c to Lightning
(4-pin plug) live cable *1 zOTG line X1
WELCOME
MELODY1
MELODY2
LAUGHTER
WELCOME
WELCOME
SLAP
KISS
DODGE MODE
WIRELESS
Original
P POP
Type-c to Type-c Charging 3.5mm monitor 3.5mm with Windproof sponge
OTG live line *1 data cable *1 headset *1 microphone *1 sleeve *1
Sound Card *1
Battery management
--Charging input: USB charger 5V 1A Type-C interface
--Remote control power supply: CR2032 button battery
1. It is recommended to turn off the battery for charging. If you want to charge it when it is turned on, it is recommended tous e
a mobile power bank to avoid interference with the current sound. Sound card and wireless microphoneIt takes 3.5 hours
to be fully charged.
2. Use a 5V 1A USB charger or power bank for charging. When the sound card is inserted into the charger, the charging port’s
red light is on; when fully charged, the blue light is on;
3. After the sound card is fully charged, the continuous use time is about 7 hours. When the sound card is low in power, the
voice broadcast is low, and the position of the charging port is red and blue.to flash instead. It will automatically shut do wn
after 2 minutes;
4. After the lavalier microphone is fully charged, the continuous use time is about 7 hours.After the power is turned on, the blue
light of the battery is always on, indicating that the battery is normal. Blinking instead, it means low power, plug in the charger,
the red light is always on, when it is fully charged, the blue light is always on, and the red light is off.
.03.
Wireless Sound Card Lavalier Microphone
Product Instruction Manual