MyPBX U200 Installation Guide MyPBX U200 Installation Guide Version: V1.0 Yeastar Technology Co., Ltd Date: 14th, January, 2013 http://www.yeastar.
MyPBX U200 Installation Guide Contents 1. PREPARATION BEFORE INSTALLATION ....................................................................................... 3 2. HARDWARE SPECIFICATIONS ...................................................................................................... 4 2.1 Overview ............................................................................................................................ 4 2.2 LED Indicators and Ports ..............................................
MyPBX U200 Installation Guide About MyPBX U200 MyPBX U200 is a workhorse designed for companies requiring up to 50 concurrent calls and 200 users. It supports PSTN, ISDN BRI lines, GSM/UMTS networks and VoIP. Also, it is equipped with an audio input port and an audio output port. MyPBX U200 is truly unrivalled for features and value. MyPBX U200’s scalability is impressive too.
MyPBX U200 Installation Guide 2. Hardware Specifications 2.1 Overview Figure 2-1 MyPBX U200 2.2 LED Indicators and Ports Figure 2-2 MyPBX U200 Front Panel http://www.yeastar.
MyPBX U200 Installation Guide Figure 2-3 MyPBX U200 Rear Panel LED Power Indication Power status Status On Off RUN MyPBX status Blinking Not Blinking/Off 1-16 FXO port status Red light GSM/ UMTS status Red light port BRI port status Orange light FXS port status Green light Ports RJ11 ports Antenna ports Description The power is switched on The power is switched off MyPBX is running properly MyPBX goes wrong The red light is blinking: the PSTN line hasn’t been connected the red and green l
MyPBX U200 Installation Guide Console port For debugging USB port For the storage of call recording files Ethernet ports MyPBX U200 provides two 10/100M adaptive RJ45 Ethernet ports, marked as LAN and WAN. -LAN port: LAN port is for the connection to Local Area Network (LAN). -WAN port: WAN port is the network port for the connection to internet. It supports ‘DHCP server’, ‘PPPoE/dynamic DNS’, and “static IP” for IP address assignment.
MyPBX U200 Installation Guide 3.2 Installation Instructions After placing MyPBX U200 in a suitable place, please connect the power adapter and all other cables to complete the installation. 3.2.1 Connection of Ethernet Ports MyPBX U200 provides two 10/100M adaptive RJ45 Ethernet ports, that is, LAN port and WAN port. WAN Port Connection Connect one end of a network cable to the WAN port of MyPBX U200, and the other end to the Ethernet port of a hub, switch or ADSL modem.
MyPBX U200 Installation Guide 2. Connection of GSM/UMTS ports If No.3 and No.7 connectors are GSM/UMTS Ports, the steps of connection are as below: Step 1: Open the Upper case of MyPBX U200 Step 2: Insert the SIM card: Figure 3-2 Inserting the SIM Card Step 3: Connect the antenna Once completed, the No.3 and No.7 LED lights would turn red as below figure: Figure 3-3 Connection of GSM/UMTS ports 3.
MyPBX U200 Installation Guide Figure 3-4 Connection of BRI ports 3.2.3 Connection of FXS ports The FXS port could be connected to an analog phone with a phone line. For instance, if No.6 and No.8 connectors are FXS ports, the connection could be depicted as below: Figure 3-5 Connection of FXS ports 3.2.4 Power Connection Once users have made sure that device installation, cable connection and power type is correct, please switch on the power. Then MyPBX U200 will start booting.
MyPBX U200 Installation Guide 3.2.5 Overall Flow Chart Figure 3-6 Overall Flow Chart 4. MyPBX U200 Basic Configurations 4.1 Factory Defaults MyPBX U200 provides web-based configuration interface for administrator and account user. The user can manage the device by log in the web interface. The factory default IP address: LAN: 192.168.5.150; Access path: http://[IP address] User Name: admin; Password: password Default SIP UDP port: 5060 There are 6 extensions set up by default.
MyPBX U200 Installation Guide Figure 4-1 MyPBX Web Configuration Panel Login Page Enter the Admin User Name and Password to log in. Figure 4-2 MyPBX Admin Configuration Interface Via the configuration interface, the admin can make all the system configurations, including network settings (LAN, WAN, Firewall, VPN, DDNS, VLAN, etc.); system parameters configuration (system prompts, time zone, password, etc.
MyPBX U200 Installation Guide just configuring the IP address of the LAN port which is connected to the local area network of the company is OK. WAN Settings Click “Network Settings”->”WAN Settings” on the left menu bar. 1. If the network that the WAN port is connected to is using DHCP server as connection method, please select the “DHCP” (dynamic IP) option. 2.
MyPBX U200 Installation Guide 4.6 Making/Receiving calls Note: The MyPBX default settings are sufficient to make phone calls. It is not necessary to make any changes unless the user wants to create new extensions or trunks. Refer to Administrator’s Guide for more. 1. Internal calls between extensions If two IP terminals have registered to MyPBX successfully, the user could make calls between extensions just by dialing the other’s extension number. 2.
