SOHO User Manual Version 1.0.1.1 Yeastar Technology Co.
MyPBX-SOHO User Manual Table of Contents 1. Introduction ............................................................................................ 4 1.1 Features ............................................................................................ 4 1.2 Hardware Specification ........................................................................ 4 1.2.1 Exterior Appearance ...................................................................... 4 1.3 Package Contents .............................
MyPBX-SOHO User Manual 3.5.1 DISA ......................................................................................... 33 3.5.2 Conferencing .............................................................................. 34 3.5.3 Time Conditions .......................................................................... 35 3.5.4 Feature Codes ............................................................................ 35 3.5.5 Paging and Intercom ..........................................................
MyPBX-SOHO User Manual 1. Introduction MyPBX — IPPBX for Small Office and Home Office 1.
MyPBX-SOHO User Manual ① ② ③ ④ ⑤ Figure 1-1 MyPBX Front Panel Picture No. ① ② ③ ④ ⑤ Identifying Green Light：Indicates the power connection is normal. Green Light：Indicates the server system is in working order Green Light：Indicates the system is ready. Green Light：Indicates the internet interface is in use Red Light：stands for FXO port Green Light：stands for FXS port LED Dual - Red blink：FXO port isn’t connecting PSTN line. LED Dual - Red and Green blink：FXO port receive an incoming call.
MyPBX-SOHO User Manual 1.3 Package Contents ▲ 1 unit of MyPBX-SOHO server ▲ 1 power supply ▲ 1 Internet line ▲ Few telephone cables [RJ-11] Note: If any of the above items is damaged or missing, contact your reseller. www.yeastar.
MyPBX-SOHO User Manual 2. System set up 2.1 Connection Drawing PSTN PSTN FXO Ports IP Provider FXS Ports LAN Router 601 602 Normal Phone IP Phone Soft Phone 2.2 Connecting Ethernet Line MyPBX provides two 10/100M Ethernet ports with RJ45 interface and LED indicator. Plug Ethernet line into MyPBX’s Ethernet port, and then connect the other end of the Ethernet line with a hub, switch, router, LAN or WAN. Once connected, check the status of the LED indicator.
MyPBX-SOHO User Manual Please follow the steps below to connect the MyPBX unit to a power outlet: 1. Connect the small end of the power cable to the power input port on the MyPBX back panel, and plug the other end of the cable into a 100VAC power outlet. 2. Check the Power LED on the front panel. A solid green LED indicates that power is being supplied correctly. www.yeastar.
MyPBX-SOHO User Manual 3. Manage MyPBX 3.1 Manager Log in From your web browser, input the IP address of the MyPBX server. If this is the first time you are configuring MyPBX, please use the default settings below: IP Address: http://192.168.5.150 Username: admin Password: password Figure 3-1 www.yeastar.
MyPBX-SOHO User Manual 3.2 Status Monitor 3.2.1 Line Status Figure 3-2 MyPBX Status Description: Extensions: 1) : extension is unregistered 2) : extension is idle 3） : extension is ringing 4） : extension is busy in a call Trunks: SIP Trunk: 1) Unregistered — trunk registration failed. 2) Registered — succeed registration, trunk is ready to use. 3) Request Send — Registering. www.yeastar.
MyPBX-SOHO User Manual 4）Waiting — Waiting for Authentication. FXO Trunk: FXO: please refer to the LED identifying of front panel. 3.3 Basic 3.3.1 Extension Extension has two types: normal desk extension (FXS) and VOIP extension. Figure 3-3 3.3.1.1 Analog Extension (FXS)） Edit Analog Extension On the administration page of FXS extensions, click ‘Edit’ on the extension that you want to edit, and modify the following information on prompt window 1) General ·Extension The numbered extension, i.e.
MyPBX-SOHO User Manual ·Caller ID The Caller ID (CID) string will be used when this user calls another internal user. 2) Voice Mail ·Voice Mail Access PIN Code Voicemail Password for this user, Ex: ‘1234’. ·Send Voice Mail to Email Address This option defines whether or not voicemails are sent to the Email address as an attachment. Note: You need to have an SMTP server configured for this functionality.
MyPBX-SOHO User Manual Figure 3-4 3.3.1.2 VOIP Extension A VOIP extension is an SIP Account that allows an IP Phone or an IP Soft- Phone client to register on MyPBX. 1. Add VOIP Extension Go to Extensions VOIP Extensions Create New Extension 1) General ·Extension The numbered extension, i.e. 1234, that will be associated with this particular User / Phone. ·Password The password for the user's sip account , Ex: ‘12t3f6’ ·Name A character-based name for this user, i.e.
MyPBX-SOHO User Manual 2) Voice Mail ·Voice Mail Access PIN Code Voicemail Password for this user, Ex: ‘1234’. ·Send Voice Mail to Email Address This option defines whether or not voicemails are sent to an Email Address as attachment. Note: You need to have an SMTP server configured for this functionality. 3) VoIP Setting ·NAT Try this setting when MyPBX is on a public IP and communicating with devices hidden behind a NAT device (broadband router).
MyPBX-SOHO User Manual Check this option to allow a user to access the MRI web interface, which allows a user to manage their saved voicemail messages and recordings. Users may access MRI by logging in with their extension number and voicemail password. Figure 3-5 2. Bulk add SIP Extensions Go to Extensions SIP Extensions Bulk add Extensions 1）Choose the extension quantity you want to create 2）The initiative extension number when starting www.yeastar.
MyPBX-SOHO User Manual Figure 3-6 3. Edit VOIP Extension Click ‘Edit’ on VOIP Extension administration page or click ‘Modify Selected Extensions’ to edit extension. 3.3.2 Trunk There are three types of trunks: Analog trunks (FXO), VOIP and Service Provider trunks. Figure 3-7 3.3.2.1 Analog Trunk (FXO) 1. Edit Analog Trunk (FXO) On the analog Trunk administration page, click ‘Edit’ on selected trunk and modify information on prompt window: www.yeastar.
MyPBX-SOHO User Manual 1）General 1）General ·Trunk Name A unique label used to identify this trunk when listed in outbound rules, incoming rules, etc. Ex: 'Port 5' ·Audio Setting Normally you should not have to adjust your analog ports beyond the initial calibration. Should you still need to fine tune your audio settings, please make adjustments as necessary. 2）Advanced Options ·Busy Detection Busy Detection is used to detect far end hang-up or for detecting a busy signal.
MyPBX-SOHO User Manual Figure 3-8 3.3.2.2 VOIP Trunk 1. Add SIP Trunk Input correct SIP information (provided by VOIP provider). Inaccurate information will prevent the trunk from registering. ·Provider Name A unique label to help you identify this trunk when listed in outbound rules, incoming rules etc. Ex: 'yeastar'. ·Hostname/IP Service provider’s hostname or IP address.5060 is the standard port number used by SIP protocol. Don’t change this part if it is not required. .
MyPBX-SOHO User Manual Figure 3-9 3.3.2.3 Service Provider 1. Add Service Provider To Create the Service provider definition you need to complete the following VoIP fields. ·Type SIP or IAX SIP – Identifies whether the trunk sends and receives calls by using the VoIP protocol SIP. IAX - Identifies whether the trunk sends and receives calls by using the VoIP protocol IAX. ·Provider Name A unique label would help to you identify this trunk. Ex: 'Provider2'.
MyPBX-SOHO User Manual Figure 3-10 3.3.3 Outbound Routes Outbound routing mainly works for guides outgoing calls to go through trunks. Figure 3-11 www.yeastar.
MyPBX-SOHO User Manual 3.3.3.1 Create Outbound Route Click ‘New Outbound Route’ and fill in the corresponding information in the popup window. 1）General ·Route Name Name of this Outbound Route. Ex: 'Local' or 'LongDistance' etc. ·Dial Pattern In dial patterns, some characters have special meanings: X ... Any Digit from 0-9 Z ... Any Digit from 1-9 N ... Any Digit from 2-9 [12345-9] ... Any Digit in the brackets (in this example, 1,2,3,4,5,6,7,8,9) . ... Wildcard, Matches Anything Remaining; i.e. 9011.
MyPBX-SOHO User Manual Figure 3-12 3.3.3.2 Delete Outbuond Route Click ‘Delete’ on selected trunk to remove the trunk. 3.3.4 Auto Provision 3.3.4.1 Create New Phone Click ‘Create New Phone’ and fill in the corresponding information in the popup window. 1）General ·MAC IP Phone’s MAC address. ·Name Name of this Phone. ·Call Waiting www.yeastar.
MyPBX-SOHO User Manual This call feature allows your phone to accept other incoming calls to an extension already in an active call. ·Key As Send ·Line Extension: Selected the extension number for IP Phone. Label: It is shown on the LCD for users to identify the account. Line Active: You can choose on/off to enable/disable the account respectively. Figure 3-13 www.yeastar.
MyPBX-SOHO User Manual 3.4 Inbound Call Control 3.4.1 IVR When there’s an inbound call aims at Auto Attendant, MyPBX will play an IVR recording and route the caller to the requested destination (for example, ‘Welcome to XX company, for sales press 1, for technical support press 2, for operator press 0, etc’). The system will transfer the call to corresponding extension according to DTMF digits inputted by the user. Figure 3-14 3.4.1.1 Create IVR Click ‘Create New IVR’.
MyPBX-SOHO User Manual ·WaitExten The number of seconds to wait before routing to the ‘Time Out’ condition of an IVR node. ·Allow Dialing Other Extensions Check this option if the user want to dial extensions directly. 2）Key Press Events Key press events will cause the system to listen for DTMF input from the caller and define the actions that occur when a user presses the corresponding digit. ·Time Out Define the timeout action.
MyPBX-SOHO User Manual 3.4.1.2 Delete IVR Select the item that you would like to remove and press the ‘Delete’ button. 3.4.2 IVR Prompts The administrator can use this screen to record IVR prompts by doing the following: 1）Click ‘Record New IVR Prompt’ 2) Input the desired file name on the popup window and choose an extension to call for recording (such as 500). 3) Click ‘Record’. The selected extension will ring and you can pick up the phone to start recording.
MyPBX-SOHO User Manual 3.4.3 Ring Groups Figure 3-18 3.4.3.1 Create Ring Group Click ‘New Ring Group’ to enter into the Manage Ring Groups page 1）General ·Ring Group Name This option defines a name for this Group, i.e. ‘Sales’. ‘Ring Group Name’ is a label to help you identify this group in the group list. ·Number for this ring group This option defines the numbered extension that may be dialed to reach this Group. ·Strategy This option sets the Ringing Strategy for this Group.
MyPBX-SOHO User Manual This selection shows all users in the group. Selecting a user here makes them a member of the current group. ·Destination If No Answer When all people on this group fail to answer the call, system will handle the call according to the selected destination. Figure 3-19 3.4.3.2 Delete Ring Group Select the item you’d like to remove and press the ‘Delete’ button. 3.4.
MyPBX-SOHO User Manual Figure 3-20 3.4.4.1 Create Inbound Route Click ‘New Inbound Route’ to enter to the Manage Inbound Routes page. 1）General ·Route Name Name of this inbound Route. Ex: 'pstncallin' etc. ·DID Number Define the expected DID Number if your trunk passes DID on incoming calls. Leave this field blank to match calls with any or no DID info. Only Service or E1 trunks need to be configured. You can also use a pattern match (e.g. 2[345]X) to match a range of numbers.
MyPBX-SOHO User Manual Define the Caller ID Number to be matched on incoming calls. Leave this field blank to match any or no DID info. You can also use a pattern match (e.g. 2[345]X) to match a range of numbers. ·Pattern Define the Caller ID Number to be matched on incoming calls. Leave this field blank to match any or no CID info. In patterns, some characters have special meanings: X ... Any Digit from 0-9 Z ... Any Digit from 1-9 N ... Any Digit from 2-9 [12345-9]...
MyPBX-SOHO User Manual Figure 3-21 3.4.4.2 Delete Routes Select the item you’d like to remove and click ‘Delete’ key. www.yeastar.
MyPBX-SOHO User Manual 3.4.5 Blacklist Number Blacklist is used to block an incoming call you do not want to answer. If the incoming call number is registered in the number blacklist, the caller will hear the following: “The number you have dialed is not in service. Please check the number and try again”. The system will then disconnect the call. Figure 3-22 3.4.5.1 Create Blacklist Click ‘New Blacklist’ to create a new number blacklist.
MyPBX-SOHO User Manual 3.5 Other Settings 3.5.1 DISA DISA (Direct Inward System Access) allows someone calling in from outside the telephone switch (PBX) to obtain an ‘internal’ system dial tone and make calls as if they were using one of the extensions attached to the telephone switch. To use DISA, a user calls a DISA number, which invokes the DISA application. The DISA application in turn requires the user to enter a PIN number, followed by the pound sign (#).
MyPBX-SOHO User Manual Figure 3-25 1) General ·DISA Name Give this DISA application a name to help you identify it. ·PIN The user will be prompted for this number. ·Response Timeout The maximum amount of time DISA will wait before disconnecting if the user has dialed an incomplete or invalid PIN number. Default is 10 seconds ·Digit Timeout The maximum amount of time permitted between digits when the user is inputting in an extension. Default is 5 seconds.
MyPBX-SOHO User Manual ·Pin Code Set an optional pin code for accessing the bridge. Figure 3-26 3.5.3 Time Conditions You can setup the business hours here. Figure 3-27 3.5.4 Feature Codes 1. General ·One Touch Record A user may initiate or stop call recording by dialing *1 during a call. (*1 is default setting) ·Extension for Checking Voice Mail www.yeastar.
MyPBX-SOHO User Manual Users can check their voice mail by dialing *2 on their phone (*2 is default setting). ·Attended Transfer Users may transfer an incoming call by dialing *3 on their phone (*3 is default setting). ·Blind Transfer Users may blind transfer an incoming call by dialing *03 on their phone (*03 is default setting).
MyPBX-SOHO User Manual User may disable always forward by calling *071 on his phone (*071 is default setting) ·Enable busy forward User may enable busy forward by calling *72 on his phone (*72 is default setting) ·Disable busy forward User may disable busy forward by calling *072 on his phone (*072 is default setting) ·Enable no answer forward User may enable no answer forward by calling *73 on his phone (*73 is default setting) ·Disable no answer forward User may disable no answer forward by calling *073 o
MyPBX-SOHO User Manual Figure 3-28 3.5.5 Paging and Intercom Paging and Intercom is a feature reserved for SIP phones that support these features. It can be used to make an announcement over the speakerphone to a phone or group of phones. Targeted phones will not ring, but answer immediately into speakerphone mode. This section is for configuring group paging and group intercom. System-wide intercom access is configured through the Feature Codes page.
MyPBX-SOHO User Manual Figure 3-29 To create a new paging group, click the ‘New Paging Group’ button. ·Number for this Paging group This option defines the numbered extension that may be dialed to reach this paging Group. ·Duplex Paging is typically one way for announcements only. Checking this will make the paging duplex, allowing all phones in the paging group to be able to talk and be heard by all. This makes it like an “instant conference”. www.yeastar.
MyPBX-SOHO User Manual Figure 3-30 3.6 System Settings 3.6.1 Options 1) General ·Ring Timeout Number of seconds to ring a device before handling the call as per the extension’s Follow Me settings. Default value is 30s. .MAX call duration The absolute maximum amount of time permitted for a call. A setting of 0 disables the timeout. Default value is 6000s. ·Music on hold Used to set hold music for the system.
MyPBX-SOHO User Manual The default value is 500 to 616 ·Paging Group Extensions The default value is 620 to 629 ·Ring Group Extensions The default value is 630 to 639 ·Conference Extensions The default value is 640 to 659 ·IVR Extensions The default value is 660 to 689 Figure 3-31 3.6.2 Music on Hold Prompts The administrator can upload on hold music as follows: 1) Click ‘Upload Music On hold File 2) Click ‘Browse’ to choose the desired audio file. 3) Click ‘Upload’ to upload the selected file.
MyPBX-SOHO User Manual Figure 3-32 3.6.3 SIP Settings 1) General ·UDP Port UDP Port to bind to, SIP standard port is 5060. ·RTP Port Start RTP Port start with ·RTP Port End RTP Port end with ·DTMF Mode Set default DTMF mode for sending DTMF. Default setting: rfc2833 ·Max Registration/Subscription Time Maximum duration (in seconds) of incoming registration allowed. Default is 3600 seconds. ·Min Registration/Subscription Time Minimum duration (in seconds) of incoming registration allowed.
MyPBX-SOHO User Manual 2) NAT ·Extern IP Address displayed in outbound SIP messages when behind a NAT. ·External Host If you specify an external host name, MyPBX will perform DNS queries on the host name periodically. Not recommended for production environments! Use External IP instead. ·External Refresh Set how often to refresh the external host if used. You may specify a local network in the field below ·Local Network Address '192.168.0.0/255.255.0.0' : All RFC 1918 addresses are local networks; '10.0.0.
MyPBX-SOHO User Manual G.726: A PSTN codec, used worldwide, that provides good voice quality and consumes 32kbit/s for each direction (receiving and transmitting) of a VoIP call. G.726 is supported by some VoIP phones. ADPCM, G.729, H261, H263, H263p, H264. Figure 3-33 3.6.4 Voicemail Settings 1) General Voicemail Settings ·Maximum messages per folder This select box sets the maximum number of messages that a user may have in any of their folders.
MyPBX-SOHO User Manual If this option is set, the caller will be asked to press 5 before he can leave a message. Setting this option will minimize auto-dialer telemarketing machines from accessing voice mail. ·Say message Caller-ID If this option is enabled, the Caller ID of the party that left the message will be played back before the voicemail message begins playing.
MyPBX-SOHO User Manual proper. Figure 3-34 3.6.5 Network Setting ·DHCP If this option is set, MyPBX will use DHCP to get an available IP address from your local network. Not recommended. ·Enable SSH Port: the default is 8022, This is the advance way to access the device, you can use the putty software to access the device. In the SSH access, you can do more advance setting and debug. ·Hostname Set the host name for MyPBX. ·IP Address www.yeastar.
MyPBX-SOHO User Manual Set the IP Address for MyPBX. ·Subnet Mask Set the subnet mask for MyPBX. ·Gateway Set the gateway for MyPBX. ·Primary DNS Set the primary DNS for MyPBX. ·Secondary DNS Set the secondary DNS for MyPBX. Figure 3-35 3.6.6 DHCP Server Dynamic Host Configuration Protocol (DHCP) is a network protocol that enables a server to automatically assign an IP address to a computer from a defined range of numbers (i.e., a scope) configured for a given network. www.yeastar.
MyPBX-SOHO User Manual Figure 3-36 3.6.7 Autobackup setting Autobackup extends the allocated disk space for backing up critical files. When properly configured, MyPBX will move all qualified files to a Windows PC every 30 minutes. For the voicemail files and recoding files, they must be created before Autobackup has been configured. For the CDR files, the call log file size must be more than 8MB. www.yeastar.
MyPBX-SOHO User Manual Figure 3-37 3.6.8 Password Settings The default password is ‘password’. To change the password, enter the new password and click update. The system will then prompt you re-login using your new password. www.yeastar.
MyPBX-SOHO User Manual Figure 3-38 3.6.9 Date and Time Set the date and time for MyPBX. www.yeastar.
MyPBX-SOHO User Manual Figure 3-39 3.6.10 Backup and Restore Backup / Restore MyPBX’s Configuration. www.yeastar.
MyPBX-SOHO User Manual Figure 3-40 3.6.11 Reset and Reboot ·Reboot Appliance Warning: Rebooting the appliance will terminate all active calls. ·Reset to Factory Defaults Warning: By resetting your System to factory defaults, you will lose all your configurations! Do not power down the MyPBX during factory default reset operations. Failure to heed this warning may result in critical damage to the unit. The unit is successfully reset when the “run” lamp begins to flash. www.yeastar.
MyPBX-SOHO User Manual Figure 3-41 3.6.12 Firmware Update Upgrading of the firmware is possible through the Administrator web interface using a TFTP Server or an HTTP URL. Enter your TFTP Server IP address and firmware file location, then click start to update the firmware. www.yeastar.
MyPBX-SOHO User Manual Figure 3-42 3.7 Reports 3.7.1 Call Logs The call Log captures all call details, including call time, caller number, callee number, call type, call duration, etc. An administrator can search and filter call data by call time, call type and call duration and can also export CDR data to a CSV file. www.yeastar.
MyPBX-SOHO User Manual Figure 3-43 3.7.2 System Info General: Information about hardware version, firmware version and system uptime. Network: Information about hostname, MAC address, IP address, subnet mask, gateway, Primary DNS and Secondary DNS. Disk Usage: Disk usage information. Memory Usage: Memory usage information. www.yeastar.
MyPBX-SOHO User Manual Figure 3-44 www.yeastar.
MyPBX-SOHO User Manual 4. Access MRI MRI (MyPBX Recording Interface: Check Voice Mail).Users may access MRI by logging into the MRI web interface with their username (extension number) and voicemail password. 4.1 Allow users to access MRI The extension’s hasmanager(web access) option must be checked before the associated user can log into MRI. Figure 4-1 4.2 User login Users can access the MRI web interface by navigating to the MyPBX IP address using a web browser.
MyPBX-SOHO User Manual Figure 4-2 4.3 Voicemail Users can check, delete, move and download voicemail files here. www.yeastar.
MyPBX-SOHO User Manual Figure 4-3 4.4 Record Users can play, delete and download record files here. www.yeastar.
MyPBX-SOHO User Manual Figure 4-4 4.5 settings Voicemail password: new voicemail box password. Enter again to confirm: confirm new voicemail box password. Send Voice Mail To Email Address: Set the email address that voicemail messages will be sent to. www.yeastar.
MyPBX-SOHO User Manual Figure 4-5 4.6 Follow me Set the mode of call forwarding when there’s incoming call on this extension. Figure 4-6 www.yeastar.
MyPBX-SOHO User Manual 5. Use MyPBX PSTN PSTN FXO Lines IP Provider FXS Lines LAN Router 601 602 Normal Phone IP Phone Soft Phone 5.1 Make outbound call To make an outbound call, we need to add trunk/service provider first.
MyPBX-SOHO User Manual 5.1.1 Make call via PSTN trunk Let’s route all inside extensions through an analog trunk by dialing 9. In Outbound Routes, add a new outbound route as below. Figure 5-1 As we can see from the outbound route of ‘pstnout’, all phone numbers starting with 9 will have their first digit stripped off (digit 9) and will be sent to the PSTN (port 1-2). After we have configured the above, we can dial 9 + local number to dial out via a PSTN line.
MyPBX-SOHO User Manual 1. Add VoIP service provider Before we do add this, please make sure you have a VoIP service provider account. Trunks SIP Trunk Add SIP Trunk Enter your account information on this page, and click Save. Figure 5-2 2. Add Outbound Routes As we can see from the Outbound Route of ‘voipout’, all phone numbers starting with 0 will have their first digit stripped off (digit 0) and will be sent to the SIP service provider. www.yeastar.
MyPBX-SOHO User Manual Figure 5-3 Now that we have added two outbound dialing rules, any call starting with 9 will be routed to the PSTN, and any number starting with 0 will be routed to the SIP provider. www.yeastar.
MyPBX-SOHO User Manual 5.2 Incoming call 5.2.1 Sample Routing to an IVR Let’s configure an incoming call to route to the IVR. In the IVR itself, let’s configure digit 0 to route the call to extension 500, and digit 1 to route the call to extension 501. 1. Add IVR To add a new IVR, go to IVR Create New IVR Figure 5-4 www.yeastar.
MyPBX-SOHO User Manual 2. Add Inbound Routes As we can see from the Inbound Route of ‘allin’, all incoming calls will be sent to the IVR. Figure 5-5 www.yeastar.
MyPBX-SOHO User Manual APPENDIX A FAQ Q1. How to Register SIP device？ A1: 1) Register SIP soft phone Download the x-lite softphone from counterpath website www.counterpath.com After install the x-lite, right click the panel and select the SIP Account setting and then configure it. Display Name: 500 User Name: 500 Password: 500 Authorization Name: 500 Domain: 192.168.5.150 2) Register IP Phone (for example, Yealink’s T28 IP Phone) a) Connect the T28’s WAN port to the switch.
MyPBX-SOHO User Manual APPENDIX B How to configure autobackup Before Autobackup can be properly configured, an SMB share folder accessible from MyPBX must be set up on a Windows based machine. Once that has been set up, please follow the steps below. Step 1 Add a new folder, rename it, and set this new folder’s share Properties according to Figure B-1 Figure B-1 Set up share Properties Step 2 Enter the new folder and create a new text file, then rename this file to status.txt.
MyPBX-SOHO User Manual Figure B-2 Autobackup Setting SMB share host/IP: Change this to the IP address of the computer where backup files will be stored. SMB share name: Change this to the name of the shared folder where backups will be stored. SMB share username: The user name used to log into the network share. Leave this blank if it is not required SMB share password: The password used to log into the network share.
MyPBX-SOHO User Manual APPENDIX C How to configure NAT setting When MyPBX is behind a NAT(firewall),you need to configure NAT setting on MyPBX if you want to use a remote extension. Please follow section 1 or 2 below depending on your network configuration. 1. If MyPBX is connected to a local network, you must set up port forwarding on your router. Specifically, you must map port 5060 (default SIP port) and port 10001-10200 (default RTP port range) as UDP ports.
MyPBX-SOHO User Manual Figure C-2 MyPBX Network setting 2. MyPBX has a public IP, it means you configure MyPBX Network setting as Figure C-3: Figure C-3 Next, you should configure the NAT settings according to Figure C-4 www.yeastar.
MyPBX-SOHO User Manual Figure C-4 External IP: The public IP address of MyPBX External Host: Leave this blank if no domain has been configured External refresh: Leave this blank Local Network Address: Leave this blank NAT mode: Yes Allow RTP Reinvite: No www.yeastar.
MyPBX-SOHO User Manual APPENDIX D How to Use Auto Provision Step 1. Disable DHCP Server on your local network. E.g. Disable DHCP Server on Linksys Router. Figure D-1 Step 2. Enable DHCP Server on MyPBX. Login MyPBX web interface, System Settings DHCP Server Enable DHCP Server. www.yeastar.
MyPBX-SOHO User Manual Figure D-2 Step 3. Configure phones on MyPBX auto-provision page. 1. Login MyPBX web interface, Basic Auto Provision Create New Phone. Figure D-3 www.yeastar.
MyPBX-SOHO User Manual 2. Fill in the phone detail message on the pop-up windows. Input IP Phone’s MAC address, configure Name, Call waiting, Line, Extension, Label, Line active for the phone. Figure D-4 Step 4. Turn on the power and connect the network cable to IP Phone. Remark: The factory default setting of DHCP for IP Phone is enable, so you can skip this step to step 5. If the DHCP is disable, please follow below step to enable it. (e.g.: Yealink’s IP Phone). 1. Login IP phone’s web page. 2.
