Table of Contents i
Table of Contents Table of Contents.................................................................. iii Summary of Changes ............................................................v Changes for Release 71, Guide Version 71.150.............................................................. v Changes for Release 71, Guide Version 71.90 ............................................................... v Changes for Release 71, Guide Version 71.80 .............................................................
Yealink SIP-T4X IP Phones Auto Provisioning Guide Phone Flash .................................................................................................................... 24 Update Mode ..................................................................... 27 Power On ........................................................................................................................ 27 Repeatedly ...................................................................................................
Summary of Changes This section describes the changes to this guide for each release and guide version. This version is updated to incorporate SIP-T41P as one of the SIP-T4X device models.
Yealink SIP-T4X IP Phones Auto Provisioning Guide vi
Introduction Yealink SIP-T4X IP phones are full-featured telephones that can be plugged directly into an IP network and can be used easily without manual configuration. This guide provides instructions on how to provision Yealink SIP-T4X IP phones with the minimum settings required. Yealink SIP-T4X IP phones support FTP, TFTP, HTTP, and HTTPS protocols for auto provisioning and are configured by default to use the TFTP protocol.
Yealink SIP-T4X IP Phones Auto Provisioning Guide 2
Getting Started This section provides instructions on how to get ready for auto provisioning. The auto provisioning process discussed in this guide uses the TFTP server as the provisioning server. To begin the auto provisioning process, the following steps are required: Obtaining Configuration Information Managing Configuration Files Before beginning provisioning, you need to obtain configuration files. There are 2 configuration files both of which are CFG-formatted.
Yealink SIP-T4X IP Phones Auto Provisioning Guide MAC Address: The unique 12-digit serial number of the phone. You can obtain it from the bar code on the back of the phone. SIP Account Information: This may include SIP credentials such as user name, password and address of the registration server. Ask your system administrator for SIP account information. Auto provisioning enables IP phones to update themselves automatically via downloading Common CFG and MAC-Oriented CFG files.
Getting Started #!version:1.0.0.1 ##File header "#!version:1.0.0.1" cannot be edited or deleted, and must be placed in the first line. #Configure the WAN port type; 0-DHCP (default), 1-PPPoE (not applicable to SIP-T42G/T41P), 2-Static IP Address #Require reboot network.internet_port.type = 0 #Configure the transmission mode and the speed of the WAN port.
Yealink SIP-T4X IP Phones Auto Provisioning Guide default time is 00:00. #If the desired end time of the day is seven forty-five p.m., the value format is 19:45. auto_provision.weekly.end_time = 00:00 #Configure the day of week for the phone to check new configuration files. The default value is 0123456. #0-Sunday,1-Monday,2-Tuesday,3-Wednesday,4-Thursday,5-Friday,6-Saturday; #If the desired week is Monday, Tuesday and Wednesday, the value format is 012. auto_provision.weekly.
Getting Started wui.https_enable = 1 # Enable or disable the web server access for HTTP; 0-Disabled, 1-Enabled (default); #Require reboot wui.http_enable = 1 #Set the HTTP port (80 by default) #Require reboot network.port.http = 80 #Set the HTTPS port (443 by default) #Require reboot network.port.https = 443 MAC-Oriented CFG file contains configuration parameters which are expected to be updated per phone, such as the registration information.
Yealink SIP-T4X IP Phones Auto Provisioning Guide ##The file header “#!version:1.0.0.1” is not a comment and must be placed in the first line. It cannot be edited or deleted. #Account 1 settings #Enable or disable the account1, 0-Disabled (Default), 1-Enabled account.1.enable = #Configure the label displayed on the LCD screen for account1 account.1.label = #Configure the display name of account 1 account.1.display_name = #Configure the user name and password for register authentication account.1.
Getting Started account.2.sip_server.2.port = # Account 3 settings #Enable or disable the account3, 0-Disabled (Default), 1-Enabled account.3.enable = #Configure the label displayed on the LCD screen for account 3 account.3.label = #Configure the display name of account3 account.3.display_name = #Configure the user name and password for register authentication account.3.auth_name = account.3.password = #Configure the register user name account.3.
Yealink SIP-T4X IP Phones Auto Provisioning Guide account.4.sip_server.2.address = account.4.sip_server.2.port = # Account 5 settings #Enable or disable the account5, 0-Disabled (Default) 1-Enabled account.5.enable = # Configure the label displayed on the LCD screen for account 5 account.5.label = #Configure the display name of account5 account.5.display_name = #Configure the user name and password for register authentication account.5.auth_name = account.5.
Getting Started account.6.sip_server.2.address = account.6.sip_server.2.port = #Configure the static IP address, submask, gateway address and DNS server address. #Require reboot network.internet_port.ip = 192.168.1.10 network.internet_port.mask = 255.255.255.0 network.internet_port.gateway =192.168.1.1 network.primary_ dns= 202.101.103.55 network.secondary_dns = 202.101.103.54 To protect against unauthorized access and tampering of sensitive information (e.g.
Yealink SIP-T4X IP Phones Auto Provisioning Guide #################################################### ## Configure the access URL of the customized ringtone ## #################################################### ringtone.url = #Delete all the custom ringtones uploaded through auto provisioning ringtone.delete = http://localhost/all For example, enter “tftp://192.168.1.100/Ring9.wav” in the “ringtone.url =” field. During the auto provisioning process, the phone connects to the provisioning server “192.
Getting Started During the auto provisioning process, the phone connects to the provisioning server “192.168.1.100”, and downloads the language file “lang+English.txt”. Available languages may vary between different firmware versions. Do not rename the language file. Logo customization allows unifying the IP phone appearance or displaying a custom image on the idle screen such as a company logo, instead of the default system logo. Logo is not applicable to the SIP-T46G and SIP-T42G IP phones.
Yealink SIP-T4X IP Phones Auto Provisioning Guide The following table lists the wallpaper image format and resolution for the SIP-T46G IP phone: Phone Model Wallpaper Image Format Resolution Size SIP-T46G .jpg/.png/.
Getting Started Where: display_name=”” specifies the name of the group. ring=”” specifies the ringtone for this group. 3. For each contact that you wish to add, add the following string to the file. Each starts on a separate line: Where: display_name=”” specifies the name of the contact (This value cannot be blank or duplicated).
Yealink SIP-T4X IP Phones Auto Provisioning Guide mobile_number="10244588666" other_number="059257000" line="0" ring="Auto" group_id_name="Lin" default_photo="" is_favorate="0" /> #################################################### ## Upload local contact file ## #################################################### local_contact.data.url = For example, enter “tftp://192.168.1.100/contact.xml” in the “local_contact.data.url =” field.
Getting Started 0, this replace rule will apply to all lines. 3. Specify the values within double quotes. 4. Save the change. The following shows an example of the replace rule file: #################################################### ## Upload replace rule file ## #################################################### dialplan_replace_rule.url = For example, enter “tftp://192.
Yealink SIP-T4X IP Phones Auto Provisioning Guide LineID=””/ lines=”” specifies the desired line(s) for this rule. When you leave it blank or enter 0, this dial-now rule will apply to all lines. 3. Specify the values within double quotes. 4. Save the change.
Configuring a TFTP Server Yealink SIP-T4X IP Phones support to use FTP, TFTP, HTTP and HTTPS protocols to download configuration files. You can use one of these protocols for provisioning. The TFTP protocol is used by default. The following section provides instructions on how to configure a TFTP server. We recommend that you use 3CDaemon or TFTPD32 as a TFTP server. 3CDaemo and TFTPD32 are free applications for Windows. You can download 3CDaemon online: http://www.oldversion.com/3Com-Daemon.
Yealink SIP-T4X IP Phones Auto Provisioning Guide If you have a 3CDaemon application installed on your local system, use it directly. Otherwise, download and install it. To configure a TFTP server: 1. Double click 3CDaemon.exe to start the application. A configuration page is shown as below: 2. Select Configure TFTP Server. Click the button to locate the TFTP root directory from the local system: 3. Click the Confirm button to finish configuring the TFTP server.
Obtaining the Provisioning Server Address Yealink SIP-T4X IP phones support to obtain the provisioning server address in the following ways: Zero Touch Plug and Play (PnP) Server DHCP Options Phone Flash The priority of obtaining the provisioning server address is as follows: Zero Touch-->PnP Server-->DHCP Options (Custom option-->option 66-->option 43) -->Phone Flash. The following sections detail the process of each way (take the SIP-T46G IP phone as an example).
Yealink SIP-T4X IP Phones Auto Provisioning Guide When Zero Touch is enabled, there will be a configuration wizard during the startup: Press the OK soft key. The network parameters are configurable via phone user interface: Press the Next soft key after finishing the network parameters. Configure the provisioning server address, authentication user name (optional) and password (optional) in the Auto Provision screen.
Obtaining the Provisioning Server Address To enable PnP via web user interface: 1. Click on Settings->Auto Provision. 2. Mark the On radio box in the PNP Active field. 3. Click Confirm to accept the change. Any PnP server activated in the network responses with a SIP NOTIFY message, and an address of the provisioning server is contained in the message body. Then the phone can connect to the provisioning server and perform the auto provisioning process.
Yealink SIP-T4X IP Phones Auto Provisioning Guide custom DHCP option, make sure the DHCP option is set properly. The custom option must be in accordance with the one defined in the DHCP server. For more information on configuring a DHCP server, refer to Configuring an HTTP Server on page 42. To configure the DHCP option via web user interface: 1. Click on Settings->Auto Provision. 2. Mark the On radio box in the DHCP Active field. 3. Enter the desired value in the Custom Option (128~254) field. 4.
Obtaining the Provisioning Server Address 2. Enter the URL, user name and password of the provisioning server in the Server URL, User Name and Password fields (the user name and password are optional). 3. Click Confirm to accept the change.
Yealink SIP-T4X IP Phones Auto Provisioning Guide 26
Update Mode The update mode is used to set the desired time for the IP phone to perform the auto provisioning process. This chapter introduces the following update modes in detail: Power On Repeatedly Weekly Auto Provision Now Multi-mode Mixed SIP NOTIFY Message When there is an active call on the phone during provisioning, the auto provisioning process will detect the call status in every 30 seconds.
Yealink SIP-T4X IP Phones Auto Provisioning Guide The phone performs the auto provisioning process at regular intervals. You can configure the interval for the Repeatedly mode. The default interval is 1440 minutes. To activate the Repeatedly mode via web user interface: 1. Click on Settings->Auto Provision. 2. Mark the On radio box in the Repeatedly field. 3. Enter the interval time in the Interval (Minutes) field. 4. Click Confirm to accept the change.
Update Mode 4. Mark one or more radio boxes in the Day of Week field. 5. Click Confirm to accept the change. You can use Auto Provision Now mode to manually trigger the phone to perform the auto provisioning process immediately. To use the Auto Provision Now mode via web user interface: 1. Click on Settings->Auto Provision.
Yealink SIP-T4X IP Phones Auto Provisioning Guide 2. Click Autoprovision Now. The phone will perform the auto provisioning process immediately. You can activate more than one update mode for auto provisioning. For example, you can activate the Power On and Repeatedly modes simultaneously, the phone performs the auto provisioning process when it is powered on and at a specified interval.
Update Mode The following figure shows the message flow: 31
Yealink SIP-T4X IP Phones Auto Provisioning Guide 32
Downloading Configurations Files Downloading Configuration Files from the Provisioning Server Once obtaining a provisioning server address in one of the ways introduced above, the phone will connect to the provisioning server and download the configuration files. The phone will try to download the Common CFG file first from the provisioning server, and then download the MAC-Oriented CFG file.
Yealink SIP-T4X IP Phones Auto Provisioning Guide Example1: Yealink SIP-T46G IP phone downloads configuration files from the TFTP server. Example 2: Yealink SIP-T46G IP phone downloads configuration files from the FTP server. Example 3: Yealink SIP-T46G IP phone downloads configuration files from the HTTP server.
Troubleshooting This chapter provides general troubleshooting information to help you solve problems you might encounter when deploying phones. If you require additional information or assistance with the deployment, contact your system administrator. Why does the phone fail to download configuration files? Ensure that auto provisioning feature is enabled. Ensure that the provisioning server and network are reachable. Ensure that authentication credentials configured on the phone are correct.
Yealink SIP-T4X IP Phones Auto Provisioning Guide Ensure that the size of the ringtone file is no larger than that the phone supports. Ensure that the properties of the ringtone for the phone are correct. Ensure that the network is available and the root directory is right for downloading. Ensure that the ringtone file exists on the provisioning server. Why doesn’t the phone update configurations? 36 Ensure that the configuration files are different from the last ones.
Glossary MAC Address: A Media Access Control address (MAC address) is a unique identifier assigned to network interfaces for communications on the physical network segment. MD5: The MD5 Message-Digest Algorithm is a widely used cryptographic hash function that produces a 128-bit (16-byte) hash value. DHCP: Dynamic Host Configuration Protocol (DHCP) is a network configuration protocol for hosts on Internet Protocol (IP) networks.
Yealink SIP-T4X IP Phones Auto Provisioning Guide 38
Appendix This section provides instructions on how to configure an FTP server using 3CDaemon. You can download the 3CDaemon software online: http://www.oldversion.com/3Com-Daemon.html. To prepare a root directory: 1. Create an FTP root directory on the local system. 2. Place the configuration files to this root directory. 3. Set the security permissions for the FTP directory folder. You need to define a user or group name, and set the permissions: read, write, and modify.
Yealink SIP-T4X IP Phones Auto Provisioning Guide If you have a 3CDaemon application installed on your local system, use it directly. Otherwise, download and install it. To configure an FTP server: 1. Double click the 3CDaemon.exe to start the application. 2. Click the FTP Server button on the left of the main page. A configuration page shows as below: 40 3. Select Configure FTP Server. 4. Click the 5. Enter the new authentication user name in the Profile field. 6.
Appendix dialogue box. 7. Click the OK button to save. 8. Mark the check boxes of Login, Download and Upload to make sure the FTP user has the login, download and upload permission. 9. Click the Save Profile button to save the settings and finish the configurations. 10. Click the Confirm button to finish configuring the FTP server. The server URL “ftp://username:password@IP/” (Here “IP” means the IP address of the provisioning server, “username” and “password” are the authentication for FTP download.
Yealink SIP-T4X IP Phones Auto Provisioning Guide This section provides instructions on how to configure an HTTP server using HFS tool. You can download the HFS software online: http://www.snapfiles.com/get/hfs.html. To prepare a root directory: 1. Create an HTTP root directory on the local system. 2. Place the configuration files to this root directory. 3. Set the security permissions for the HTTP directory folder.
Appendix The main configuration page is shown as below: 2. Click Menu in the main page and select the IP address of the PC from IP address.
Yealink SIP-T4X IP Phones Auto Provisioning Guide The default HTTP port is 8080. You can also reset the HTTP port (make sure there is no port conflict). 3. Right click the icon on the left of the main page, select Add folder from disk to add the HTTP Server root directory.
Appendix 4. Locate the root directory from the local system. Select the kind of folder which you want. 5. Check the server URL “http:// IP:Port/” in the “Open in browser” address bar (For example, the server URL ”http:// 10.2.11.101:8088/” is shown on the screenshot) . We recommend that you can fill the server URL in the address bar of the web browser and then press key to check the HTTP server before provisioning.
Yealink SIP-T4X IP Phones Auto Provisioning Guide 2. Click the Login button (the login password is blank) to log in. 3. You can then edit the existing DHCP server, or you can right click localhost and select New Server to add a new DHCP server.
Appendix 4. Right click Scopes and select New Scope. 5. Configure the DHCP server name, the DHCP IP range and the subnet mask. 6. Click OK to accept the change. 7. You can add a custom option via DHCP Turbo. Select Option Types, right click one of the options on the right of the main page, and then select New Option Type.
Yealink SIP-T4X IP Phones Auto Provisioning Guide 8. Set the custom DHCP option (custom DHCP option tag number ranges from 128 to 254) and select the option type (Yealink supports String and IP Address option types only). Click the OK button to finish setting the option properties. Click to save the change. 9. Click Named Policies-->Global, right click the blank area on the right of the main page and then select New Option.
Appendix 10. Scroll down and double click the custom option 128. 11. Fill the provisioning server address in the input field. 12. Click the OK button to finish setting a custom option. 13. Click to save the change.
Yealink SIP-T4X IP Phones Auto Provisioning Guide You can add the option 66 via DHCP Turbo. The following shows the detailed processes. 1. Click Named Policies-->Global, right click the blank area on the right of the main page and then select New Option. 50 2. Select TFTP Options from the pull-down list of Filter. 3. Scroll down and double click MS option 66.
Appendix 4. Fill the provisioning server address in the input field. 5. Click the OK button to finish setting a custom option. 6. Click to save the change. You also can add the option 43. The following shows the detailed processes. 1. Click Named Policies-->Global, right click the blank area on the right of the main page and then select New Option. 2. Select Standard Options from the pull-down list of Filter. 3. Scroll down and double click 43.
Yealink SIP-T4X IP Phones Auto Provisioning Guide 4. Fill the provisioning server address in the input field. 5. Click the OK button to finish setting a custom option. 6. Click to save the change. If you have installed the Cool Edit application, double click to open it. Otherwise, you can download the installation package online: http://www.toggle.com/lv/group/view/kl36218/Cool_Edit_Pro.htm and install it. To customize a ringtone using Cool Edit Pro: 52 1. Open the Cool Edit Pro application. 2.
Appendix A sample audio file loaded is shown as below: 4. Select and copy the audio waveform. 5. Select File->New to create a new file, set the channels as Mono, the sample rate as 8000 and the resolution as 16-bit. 6. Paste the audio waveform to the new file. 7. Select File->Save as to save the new audio file. On the Save waveform page, select the file format as A/mu-law wave. The original picture format must be *.bmp or *.gif.
Yealink SIP-T4X IP Phones Auto Provisioning Guide 1. Double click the PictureExDemo.exe. 2. Click Add button to open a *.bmp or *.gif file. You can repeat the second step to add multiple original picture files. 3. Click the Convert button. Then you can find the DOB logo files in the adv directory.
Appendix If you want to reset the configuration of a parameter to factory setting, set the value of the parameter to be !NULL! or %NULL%. For example, local_time.ntp_server1 = %NULL%. After the auto provisioning process is completed, the NTP server 1 will be reset to “cn.pool.ntp.org”. Parameter Permitted Descriptions Values Web Setting Path It configures the IP address mode. 0-IPv4 network.
Yealink SIP-T4X IP Phones Auto Provisioning Guide ay = the Internet (WAN) port type for IPv4 is Gateway configured as Static IP Address. The default value is blank. It takes effect after reboot. It configures the primary IPv4 DNS server when the IP address mode is network.prima ry_dns = defined as IPv4 or IPv4&IPv6, and the IP address Internet (WAN) port type for IPv4 is configured as Static IP Address. The default value is blank.
Appendix type for IPv6 is configured as Static IP Prefix (0~128) Address. The default value is 64. It takes effect after reboot. It configures the IPv6 address when the IP address mode is configured as IPv6 or IPv4&IPv6, and the Internet (WAN) network.ipv6_i nternet_port.i IP address port type for IPv6 is configured as Static IP Address. p= The default value is blank. Network->IPv6 Config->Static IP Address->IP Address It takes effect after reboot.
Yealink SIP-T4X IP Phones Auto Provisioning Guide It specifies the host name the phone sends via the DHCP option 12. network.dhcp _host_name = The default value is: String SIP-T46G (for SIP-T46G) SIP-T42G (for SIP-T42G) Features->General Information->DHCP Hostname SIP-T41P (for SIP-T41P) It enables or disables the PC port. network.pc_p ort.enable = 0 or 1 0-Disabled 1-Enabled The default value is 1. It configures the transmission mode and transmission speed of the Internet (WAN) port.
Appendix It takes effect after reboot. network.vlan.i Integer nternet_port_v from 1 to id = network.vlan.i nternet_port_p riority = 4094 Integer from 0 to 7 It configures VLAN ID of the Internet Network-> (WAN) port. Advanced->VLAN The default value is 1. ->WAN Port->VID It takes effect after reboot. (1-4094) It configures VLAN priority of the Network-> Internet (WAN) port. Advanced->VLAN The default value is 0. ->WAN Port-> It takes effect after reboot.
Yealink SIP-T4X IP Phones Auto Provisioning Guide It enables or disables the HTTP protocol for web server access. wui.http_enab le = 0-Disabled 0 or 1 1-Enabled The default value is 1. Network-> Advanced->Web Server->HTTP It takes effect after reboot. It enables or disables the HTTPS protocol for web server access. wui.https_ena ble = 0-Disabled 0 or 1 1-Enabled The default value is 1. Network-> Advanced->Web Server->HTTPS It takes effect after reboot. network.port.h ttp = network.port.
Appendix It configures the 802.1x mode. 0-Disabled 1-EAP-MD5 network.802_1 x.mode = 0, 1, 2, 3 or 4 2-EAP-TLS 3-PEAP-MSCHAPv2 Network-> Advanced->802.1x ->Mode 802.1x 4-EAP-TTLS/EAP-MSCHAPv2 The default value is 0. It takes effect after reboot. It configures the user name for 802.1x network.802_1 x.identity = authentication. String The default value is blank. Network-> Advanced->802.1x ->Identity It takes effect after reboot. It configures the password for 802.1x network.802_1 x.
Yealink SIP-T4X IP Phones Auto Provisioning Guide = 3600 request. Packet Interval The default value is 60. (1~3600s) It takes effect after reboot. It enables or disables SNMP feature. network.snmp .enable = (not 0 or 1 applicable to SIP-T42G/T41P) 0-Disabled Network-> 1-Enabled Advanced->SNMP The default value is 1. ->Active It takes effect after reboot. network.snmp .port = (not applicable to Integer from 1 to 65535 It configures the SNMP port. Network-> The default value is 161.
Appendix 1-Enabled The default value is 0. It takes effect after reboot. It configures the phone to export log files to a syslog server or the local system. syslog.mode 1 or 2 1-Local 2-Server Settings-> Configuration->Exp ort System Log The default value is 1. It configures the IP address or domain syslog.server = IP address name of the syslog server when the Settings-> syslog mode is configured as server. Configuration-> The default value is blank. Server Name It takes effect after reboot.
Yealink SIP-T4X IP Phones Auto Provisioning Guide It configures the vendor name of the auto_provision .pnp_event_v String endor = device. The default value is yealink. It enables or disables the phone to check the new configuration auto_provision .repeat.enabl repeatedly. 0 or 1 e= 0-Disabled 1-Enabled Settings->Auto Provision-> Repeatedly The default value is 0. auto_provision .repeat.
Appendix It configures the user name for auto_provision .server.userna String me = provisioning. The default value is blank. It configures the password for auto_provision .server.passw authentication during auto String ord = authentication during auto provisioning. The default value is blank. Settings->Auto Provision->User Name Settings->Auto Provision-> Password It enables or disables the phone to obtain the provisioning server address auto_provision .dhcp_option. by detecting DHCP options.
Yealink SIP-T4X IP Phones Auto Provisioning Guide It takes effect after reboot. applicable to SIP-T42G/T41P) It configures the code to trigger auto provisioning. autoprovision. The maximum length of the code is 100 X.code = characters. Valid characters are digits, (X ranges from 1 to 50.) String # and *. Example: (not applicable to autoprovision.1.code = *99 SIP-T42G/T41P) The default value is blank. It takes effect after reboot. autoprovision. X.
Appendix autoprovision. X.mac_aes = It configures the AES key (16 (X ranges characters) for decrypting the from 1 to 50.) String MAC-Oriented CFG file. (not The default value is blank. applicable to It takes effect after reboot. SIP-T42G/T41P) It enables or disables the phone to reserve the pound sign when dialing out. sip.use_23_as _pound = 0 or 1 0-Disabled (convert the pound sign into “%23”) 1-Enabled Features->General Information-> Reserve # in User Name The default value is 1.
Yealink SIP-T4X IP Phones Auto Provisioning Guide bootup. 0-Disabled 1-Enabled The default value is 0. managements It enables or disables TR069 feature. erver.enable = (not 0-Disabled 0 or 1 1-Enabled The default value is 0. applicable to Settings->TR069-> Enable TR069 It takes effect after reboot. SIP-T42G/T41P) managements erver.usernam e= (not It configures the user name for the String phone to authenticate with the ACS. It takes effect after reboot.
Appendix SIP-T42G/T41P) managements It enables or disables the phone to erver.periodic report its configuration to the ACS. _inform_enabl e= 0-Disabled 0 or 1 (not 1-Enabled The default value is 1. applicable to Settings->TR069-> Enable Periodic Inform It takes effect after reboot. SIP-T42G/T41P) managements It configures the interval (in seconds) erver.
Yealink SIP-T4X IP Phones Auto Provisioning Guide 1-Attended Transfer 2-Blind Transfer The default value is 2. It enables or disables the phone to transfer call to the two parties after a transfer.tran_o thers_after_co local conference call hangup. 0 or 1 nf_enable = Features->Transfer ->Transfer on 0-Disabled Conference Hang 1-Enabled up The default value is 0. It enables or disables the voice activity detection. voice.
Appendix Custom, Australia, Austria, Brazil, Belgium, China, Czech, Denmark, Finland, France, Germany, Great Britain, Greece, voice.tone.cou ntry = Hungary, It configures the tone type for the Lithuania, phone. India, Italy, The default value is Custom. Settings->Tones-> Select Country Japan, Mexico, New Zealand, Netherlands, Norway, Portugal, Spain, Switzerland, Sweden, Russia, United States, Chile Czech ETSI It customizes the dial tone when the parameter "voice.tone.
Yealink SIP-T4X IP Phones Auto Provisioning Guide be composited at most four different frequencies. Duration: the duration (in milliseconds) of the ring tone, ranges from 0 to 30000ms. The exclamation point (!) can be added optionally, which means the custom tone will be only played once. You can configure at most eight different tones for one condition. Tones are separated by comma (e.g., 250/200, !0/1000, 200+300/500, 600+700+800+1000/2000). It customizes the ring-back tone when the parameter "voice.tone.
Appendix Custom. The value format is F/D or !F/D. For more information on the value format, refer to the parameter “voice.tone.dial”. The default value is blank. It customizes the redial tone when the parameter "voice.tone.country" is configured as Custom. voice.tone.dia lrecall = String The value format is F/D or !F/D. For Settings->Tones-> more information on the value format, Dial Recall refer to the parameter “voice.tone.dial”. The default value is blank.
Yealink SIP-T4X IP Phones Auto Provisioning Guide It customizes the message tone when the parameter “voice.tone.country” is voice.tone.me configured as Custom. ssage = (not String applicable to The value format is F/D or !F/D. For Settings->Tones-> more information on the value format, Message refer to the parameter SIP-T42G/T41P) “voice.tone.dial”. The default value is blank. It customizes the auto answer tone when the parameter “voice.tone.country” is configured as Custom. voice.tone.
Appendix voice.ring_vol = voice.group_s pk_vol = Integer from 0 to 15 Integer from 0 to 15 It configures the volume of ringer. The default value is 8. It configures the receiving volume of the group listening mode. The default value is 8. It configures the strategy for ring-back tone. 1-Ignore: the phone plays the mix of defined tone and received RTP for ring-back tone voice.call_pre view_mode = 1, 2 or 3 2-Force: the phone discards the received RTP and plays the defined tone for ring-back tone.
Yealink SIP-T4X IP Phones Auto Provisioning Guide It takes effect after reboot. It specifies the type of certificates for the phone to send for TLS authentication. security.dev_c ert = 0 or 1 Security->Server 0-Default certificates Certificates-> 1-Custom certificates Device Certificates The default value is 0. It takes effect after reboot. security.user_n ame.user = security.user_n ame.admin = security.user_n ame.var = String String String It configures the user name for web server access.
Appendix custom_softke y_ring_back.ur It configures the access URL of the file URL l= for custom soft key layout presented on the LCD screen when Ringback. Settings->Softkey Layout It configures the access URL of the custom_softke y_talking.url = URL customized file for the soft key Settings->Softkey presented on the LCD screen when Layout Talking. It configures the desired feature for line key X.
Yealink SIP-T4X IP Phones Auto Provisioning Guide 34-Hot Desking 35-URL Record 38-LDAP 40-Prefix 41-Zero Touch 42-ACD 45-Local Group 50-Keyboard Lock 61-Directory It configures the desired line to apply the key feature. When the key feature is configured to Local Group or XML Group, this parameter is used to specify the desired phone book (or group) when multiple phone books (or groups) are configured on the IP phone. linekey.X.
Appendix 1 to 15.) linekey.X.exte nsion = (SIP-T46G: X ranges from 1 to 27. It configures the pickup code for BLF String feature. The default value is blank. SIP-T42G/T41P: DSSKey->Line Key->Extension X ranges from 1 to 15.) linekey.X.label = (SIP-T46G: X ranges from 1 to 27. It configures the label displaying on String the LCD screen for each line key. The default value is blank. SIP-T42G/T41P: DSSKey->Line Key->Label X ranges from 1 to 15.
Yealink SIP-T4X IP Phones Auto Provisioning Guide 33-Status 34-Hot Desking 40-PTT 43-Local Phone Book 45-Local Group 47-XML Directory It configures the desired line to apply the programmable key feature. When the key feature is configured to Local Group or XML Group, this programablek parameter is used to specify the ey.X.line = desired phone book (or group) when multiple phone books (or groups) are (SIP-T46G: X ranges from 1 to 13. Integer from 1 to 6 configured on the IP phone.
Appendix 1 to 40.) expansion_mo dule.X.key.Y.lin e= (X ranges from 1 to 6. It configures the desired line to apply Integer from 1 to 6 the expansion module key feature. Valid values are the same as those of DSSKey->Ext Key the parameter “linekey.X.line”. Y ranges from 1 to 40.) expansion_mo dule.X.key.Y.v alue = (X ranges from 1 to 6. Y ranges from String It configures the value of the expansion module key. DSSKey->Ext Key 1 to 40.) (not applicable to SIP-T42G/T41P) expansion_mo dule.X.key.Y.
Yealink SIP-T4X IP Phones Auto Provisioning Guide different states of line keys. Tips 0-Disabled 1-Enabled The default value is 0. Default.jpg, 1.png, 2.png, phone_setting .backgrounds = 3.png, It configures the wallpaper displayed on the phone. Example: 4.png, phone_setting.backgrounds = 1.png Settings->Preferenc 5.png, To configure a custom picture (e.g., e->Wallpaper 6.png, custom1.png) to be wallpaper, the 7.png, value format is: Resource:custom1.png 8.
Appendix It enables or disables busy forward feature. forward.busy. enable = 0 or 1 Features->Forward 0-Disabled &DND->Busy 1-Enabled Forward->On/Off The default value is 0. forward.busy.t arget = String It configures the target number the Features->Forward phone forwards incoming calls to &DND->Busy when busy. Forward->Target Features->Forward forward.busy. on_code = String It configures the busy forward on code. &DND->Busy Forward->On Code Features->Forward forward.busy.
Yealink SIP-T4X IP Phones Auto Provisioning Guide 0-Disabled 1-Enabled The default value is 1. It enables or disables the phone to automatically change the status of the acd.auto_avai lable = ACD agent to available. 0 or 1 0-Disabled Features->ACD-> ACD Auto Available 1-Enabled The default value is 0. It configures the interval (in seconds) acd.auto_avai Integer lable_timer = from 0 to 120 to automatically change the status of the ACD agent to available. The default value is 60.
Appendix It configures the action URL the phone sends after account register. action_url.log_ on = URL Example: Features->Action URL->Registered action_url.log_on = http://192.168.0.20/help.xml?ip=$ip It configures the action URL the phone sends after account unregister. action_url.log_ off = URL Example: Features->Action action_url.log_off = URL->Unregistered http://192.168.0.20/help.xml?model=$ model It configures the action URL the phone sends after register failed. action_url.
Yealink SIP-T4X IP Phones Auto Provisioning Guide action_url.outgoing_call = http://192.168.0.20/help.xml?model=$ model It configures the action URL the phone sends when establishing a call. action_url.call _established URL = Example: Features->Action action_url.call_established = URL->Established http://192.168.0.20/help.xml?model=$ model It configures the action URL the phone sends when DND feature is enabled. action_url.dnd _on = URL Example: Features->Action action_url.
Appendix action_url.busy_fwd_on = http://192.168.0.20/help.xml?model=$ model It configures the action URL the phone sends when busy forward feature is action_url.bus y_fwd_off = URL disabled. Features->Action Example: URL->Close Busy action_url.busy_fwd_off = Forward http://192.168.0.20/help.xml?model=$ model It configures the action URL the phone sends when no answer forward action_url.no_ answer_fwd_o URL n= feature is enabled. Features->Action Example: URL->Open No action_url.
Yealink SIP-T4X IP Phones Auto Provisioning Guide _call = or a semi-attended transfer. Transfer Example: action_url.attended_transfer_call = http://192.168.0.20/help.xml?model=$ model It configures the action URL the phone sends when placing a call on hold. action_url.hol d= URL Example: Features->Action action_url.hold = URL->Hold http://192.168.0.20/help.xml?model=$ model It configures the action URL the phone sends when resuming a held call. action_url.
Appendix http://192.168.0.20/help.xml?model=$ model It configures the action URL the phone sends when canceling the call in the connecting interface. action_url.call _interrupt = URL Example: action_url.call_terminated = http://192.168.0.20/help.xml?model=$ model It configures the action URL the phone sends when changing the state of the phone from busy to idle. action_url.bus y_to_idle = URL Example: Features->Action URL->Busy to Idle action_url.busy_to_idle = http://192.168.0.20/help.
Yealink SIP-T4X IP Phones Auto Provisioning Guide all = Example: Incoming Call action_url.reject_incoming_call = http://192.168.0.20/help.xml?model=$ model It specifies the URL the phone sends when canceling the dial-out. action_url.call _interrupt = URL Example: action_url.call_interrupt = http://192.168.0.20/help.xml?model=$ model It configures the action URL the phone sends when answering a new incoming call. action_url.ans wer_new_inco URL Example: action_url.
Appendix English, Chinese_S, Chinese_T, German, lang.gui = It configures the language of the phone user interface. French, The default value is English. Turkish, Note: Chinese_S and Chinese_T are Italian, not applicable to SIP-42G/T41P IP Polish, phones. Spanish or Portuguese local_time.tim e_zone = String String = local_time.ntp _server1 = local_time.ntp _server2 = local_time.inte rval = Settings-> Time & The default value is +8. Date-> Time Zone It configures the time zone name.
Yealink SIP-T4X IP Phones Auto Provisioning Guide Month/Day/Hour (for By Date) Date-> Start Date Month/ Day of Week/ Day of For DST By Week: Week Last in Month/ Hour of Day Settings ->Time & (for By Week) Date-> DST Start The default value is 1/1/0. Month/DST Start Day of Week/ DST Start Day of Week Last in Month/ Start Hour of Day Settings ->Time & It configures the time to end DST. Value formats are: local_time.
Appendix 5-DD MMM YYYY 6-WWW DD MMM The default value is 0. It enables or disables the phone to update time with the offset time obtained from the DHCP server. local_time.dhc p_time = 0 or 1 It is only available to the time zone 0. 0-Disabled Settings ->Time & Date-> DHCP Time 1-Enabled The default value is 0. It enables or disables the phone to provide input field of register name on hotdesking.st artup_register _name_enabl the hot desking login wizard during 0 or 1 startup.
Yealink SIP-T4X IP Phones Auto Provisioning Guide 0-Disabled 1-Enabled The default value is 0. It enables or disables the phone to show the register name item on the hotdesking.ds skey_register_ name_enable login wizard when pressing the Hot 0 or 1 Desking key. 0-Disabled = 1-Enabled The default value is 0. It enables or disables the phone to show the user name item on the login wizard when pressing the Hot Desking hotdesking.ds skey_usernam 0 or 1 key.
Appendix distinctive_rin g_tones.alert_i nfo.X.text = String (X ranges It configures the internal ringer text for Settings->Ring-> distinctive ringtone. Internal Ringer Text from 1 to 10.) distinctive_rin g_tones.alert_i nfo.X.ringer = (X ranges It configures the desired ring tone for Integer from 1 to 8 from 1 to 10.) each text. The value ranges from 1 to 8, each Settings->Ring-> Internal Ringer File digit stands for an appropriate ringtone.
Yealink SIP-T4X IP Phones Auto Provisioning Guide It enables or disables the phone to block displaying the push XML push_xml.bloc k_in_calling = interface when in calling status. 0 or 1 0-Disabled 1-Enabled Features->Remote Control->Block XML In Calling The default value is 0. It enables or disables the phone to use the push XML via SIP NOTIFY message. push_xml.sip_ notify = 0 or 1 0-Disabled 1-Enabled Features-> Remote Control->SIP Notify The default value is 0.
Appendix dialplan.area _code.line_id = It configures lines applying the area (SIP-T46G: X ranges from 1 Number to 6. code. Line IDs are separated by comma. The default value is blank. SIP-T42G/T41P: Settings->Dial Plan->Area Code->Account X ranges from 1 to 3.) dialplan.block Settings->Dial _out.number.X = String (X ranges It configures the block out number. Plan->Block The default value is blank. Out->BlockOut Number X from 1 to 10.) dialplan.
Yealink SIP-T4X IP Phones Auto Provisioning Guide The default value is blank. remote_phone It configures the access URL of the book.data.X.u rl = URL (X ranges remote phone book. The URL cannot contain the character <>'" \. from 1 to 5.) Directory->Remote Phone Book-> Remote URL remote_phone book.data.X.n ame = String (X ranges It configures the display name of the remote phone book item. Directory->Remote Phone Book-> Display Name from 1 to 5.
Appendix ldap.base = dc=yealink,dc=cn The default value is blank. It configures the user name for ldap.user = String accessing the LDAP server. The default value is blank. ldap.passwor d= ldap.max_hits = It configures the password for String accessing the LDAP server. The default value is blank. Integer from 1 to 32000 Directory->LDAP-> User Name Directory->LDAP-> Password It configures the maximum of the search results returned by the LDAP Directory->LDAP-> server.
Yealink SIP-T4X IP Phones Auto Provisioning Guide It enables or disables the phone to perform an LDAP search when ldap.call_in_lo okup = receiving an incoming call. 0 or 1 0-Disabled 1-Enabled Directory->LDAP-> LDAP Lookup For Incoming Call The default value is 0. It enables or disables the phone to sort the search results in alphabetical order ldap.ldap_sort = or numerical order. 0 or 1 0-Disabled 1-Enabled Directory->LDAP-> LDAP Sorting Results The default value is 0.
Appendix The default value is 0. features.dnd.o n_code = features.dnd.o ff_code = String String It configures the DND on code when the DND mode is configured as Phone. It configures the DND off code when the DND mode is configured as Phone. Features->Forward & DND->DND-> DND On Code Features->Forward & DND->DND-> DND Off Code It enables or disables the phone to receive the calls from the authorized features.dnd.e mergency_en number when the DND is enabled.
Yealink SIP-T4X IP Phones Auto Provisioning Guide intercom call. 0-Disabled 1-Enabled The default value is 1. It enables or disables the phone to mute the speaker when answering an features.interc om.mute = intercom call. 0 or 1 0-Disabled Features->Intercom ->Intercom Mute 1-Enabled The default value is 0. It enables or disables the phone to play a warning tone when answering features.interc om.tone = an intercom call.
Appendix The default value is 21600. features.hotlin e_number = features.hotlin e_delay = number Integer from 0 to 10 It configures the hotline number. The default value is blank. Features->General Information-> Hotline Number It configures the delay time (in Features->General seconds) for the phone to dial out the Information-> hotline number automatically. Hotline Delay The default value of delay time is 4. (0~10s) It enables or disables the phone to suppress the display of DTMF digits.
Yealink SIP-T4X IP Phones Auto Provisioning Guide It enables or disables headset prior feature. features.head set_prior = 0 or 1 Features->General 0-Disabled Information-> 1-Enabled Headset Prior The default value is 0. It enables or disables dual headset feature. features.head set_training = 0 or 1 Features->General 0-Disabled Information-> 1-Enabled Dual-Headset The default value is 0. features.busy_ tone_delay = It configures the duration time (in 0, 3 or 5 seconds) for the busy tone.
Appendix It enables or disables the phone to play a warning tone when there is a features.play_ hold_tone.ena call on hold. 0 or 1 ble = 0-Disabled 1-Enabled Features->General Information->Play Hold Tone The default value is 1. features.play_ It configures the interval (in seconds) Features->General hold_tone.del for playing a hold warning tone. Information->Play The default value is 30. Hold Tone Delay Integer ay = features.redial _tone = It customizes the redial tone.
Yealink SIP-T4X IP Phones Auto Provisioning Guide The default value is 1. features.auto_ answer_delay = Integer from 1 to 4 It configures the delay time (in seconds) of auto answer. The default value is 1. It enables or disables the phone to perform a blind transfer by pressing features.dsske y_blind_tran = the predefined transfer DSS key. 0 or 1 0-Disabled 1-Enabled The default value is 1. features.relog _offtime = Integer from 1 to 1000 It configures the web login timeout (in minutes).
Appendix It enables or disables the phone to display the GPickup soft key when the features.picku p.group_picku phone is in the pre-dialing interface. 0 or 1 p_enable = 0-Disabled 1-Enabled Features->Call Pickup->Group Call Pickup The default value is 0. features.picku It configures the group call pickup Features->Call p.group_picku code. Pickup->Group Call The default value is blank.
Yealink SIP-T4X IP Phones Auto Provisioning Guide It enables or disables the power LED indicator when the phone is idle, in the features.idle_t alk_power_le d_flash_enabl pre-dialing screen or during a call. 0 or 1 e= 0-Disabled 1-Enabled The default value is 0. It enables or disables the phone to play the warning tone when receiving features.voice _mail_tone_en a voice mail. 0 or 1 able = 0-Disabled 1-Enabled The default value is 1.
Appendix 0-2aB 1-123 2-abc 3-ABC The default value is 0. It enables or disables the phone with active accounts to play tones in the dialing interface differently from the features.partiti on_tone = 0 or 1 phone with no active accounts. 0-Disabled 1-Enbaled The default value is 0. It enables or disables forward diversion feature. features.fwd_ diversion_ena 0 or 1 ble = Features->General 0- Disabled Information->Diver 1-Enabled sion/History-Info The default value is 1. features.
Yealink SIP-T4X IP Phones Auto Provisioning Guide multicast.recei ve_priority.pri ority = Integer from 0 to 10 It configures the priority of multicast Directory-> paging calls. Multicast IP-> The default value is 10. Paging Barge It configures the listening multicast IP multicast.listen address and port number for the _address.X.ip_ phone. address = Directory-> The default value is blank. Multicast IP-> (X ranges Example: Listening Address from 1 to 10.) multicast.listen_address.1.
Appendix nlock_pin = The default value is 123. Unlock PIN (0~15 Digital) It configures the interval (in seconds) phone_setting Integer to automatically lock the keypad. Features->Phone .phone_lock.lo from 0 to The default value is 0 (the keypad can Lock->Phone Lock ck_time_out = 3600 be locked only by pressing the keypad Time Out (0~3600s) lock key). It configures the ringtone for the phone. Ring1.wav, phone_setting .ring_type = Ring2.wav, …… Ring8.wav Example: Settings-> phone_setting.
Yealink SIP-T4X IP Phones Auto Provisioning Guide 2-2min 5-5min 10-10min 30-30min phone_setting .ring_for_tranf ailed = Ring1.wav It configures the ringtone when the Ring2.wav phone fails to transfer a call. .... Ring8.wav Note: Ring 6-8 are not applicable to the SIP-T42G/T41P IP phones. It enables or disables the phone to show the logon wizard during startup. phone_setting .logon_wizard 0 or 1 = Features->General 0-Disabled Information-> 1-Enabled Logon Wizard The default value is 0.
Appendix umber = comma. The default value is 120, 911 and 110. It enables or disables T9 predictive phone_setting .search_when _dialing_enab text in the dialing screen. 0 or 1 0-Disabled 1-Enabled le = The default value is 0. It enables or disables recent call in dialing feature. If it is enabled, you can view the super_search. recent_call = 0 or 1 placed calls list when the phone is in the pre-dialing screen. 0-Disabled Directory-> Setting->Recent Call In Dialing 1-Enabled The default value is 0.
Yealink SIP-T4X IP Phones Auto Provisioning Guide server_certific ates.url = server_certific ates.delete = local_contact. data.url = auto_dst.url = dialplan_dialn ow.url = dialplan_repl ace_rule.url = URL URL url = certificate files. The valid value is: http://localhost/all. URL URL URL URL URL n.url = configuration. server certificate file.
Appendix super_search. url = URL It configures the access URL of the Search Source List setting file. account.X.ena ble = It enables or disables the account X. (SIP-T46G: X ranges from 1 to 6. 0 or 1 SIP-T42G/T41P: 0-Disabled Account->Register 1-Enabled ->Line Active The default value is 0. X ranges from 1 to 3.) account.X.lab el = (SIP-T46G: X ranges from 1 to 6. It configures the label displayed on the String LCD screen for account X. The default value is blank.
Yealink SIP-T4X IP Phones Auto Provisioning Guide X ranges from 1 to 3.) account.X.use r_name = (SIP-T46G: X ranges from 1 to 6. It configures the register user name for String account X. The default value is blank. SIP-T42G/T41P: Account->Register -> User Name X ranges from 1 to 3.) account.X.sip_ server.Y.addre ss = (SIP-T46G: X ranges from 1 IP address to 6. or domain SIP-T42G/T41P: name It configures the IP address or domain name of server Y for account X.
Appendix Y ranges from 1 to 2.) account.X.sip_ server.Y.retry_ counts = It configures the times for the phone to (SIP-T46G: X ranges from 1 to 6. SIP-T42G/T41P: Integer from 0 to 20 X ranges from retransmit the request when the SIP Account->Register server Y is unavailable or there is no ->SIP Server Y respond from the SIP server Y for ->Server Retry account X. Counts The default value is 3. 1 to 3. Y ranges from 1 to 2.) It configures the transport type for account X. account.X.
Yealink SIP-T4X IP Phones Auto Provisioning Guide X ranges from When the working server fails, the 1 to 3.) phone registers to the fallback server. The default value is 0. account.X.fall It configures the time interval (in back.timeout seconds) for the phone to detect = whether the working server is (SIP-T46G: X ranges from 1 to 6. Integer from 10 to 2147483647 available by sending the registration request after the fallback server takes over the call control.
Appendix Y ranges from When the value is configured between 1 to 2.) 1 and 59, the phone automatically sets the time interval to 60. Note: This parameter is only valid when the parameter “account.X.sip_server.Y.failback_mode ” is configured to 3. The default value is 3600. account.x.sip_ server.y.regist er_on_enable It enables or disables the IP phone to = register to the secondary server before (SIP-T46G: X ranges from 1 to 6. sending requests to the secondary 0 or 1 server in the failover mode.
Yealink SIP-T4X IP Phones Auto Provisioning Guide ranges from 1 to 6. SIP-T42G/T41P: X ranges from 1 to 3.) voice_mail.nu mber.X = (SIP-T46G: X ranges from 1 to 6. String SIP-T42G/T41P: It configures the voice mail number for Account-> account X. Advanced->Voice The default value is blank. Mail X ranges from 1 to 3.) account.X.pro xy_require = (SIP-T46G: X ranges from 1 to 6. It configures the proxy server for String account X. The default value is blank.
Appendix (SIP-T46G: X ranges from 1 to 6. SIP-T42G/T41P: X ranges from 1 to 3.) account.X.ano nymous_call_o ffcode = (SIP-T46G: X It configures the code for deactivating Account->Basic-> ranges from 1 anonymous call feature for account X. Anonymous The default value is blank. Call->Off Code String to 6. SIP-T42G/T41P: X ranges from 1 to 3.) account.X.reje ct_anonymous It enables or disables anonymous call _call = rejection feature for account X.
Yealink SIP-T4X IP Phones Auto Provisioning Guide 1 to 3.) account.X.dnd It enables or disables DND feature for .enable = account X when the DND mode is (SIP-T46G: X ranges from 1 to 6. configured to “custom”. 0 or 1 0-Enabled SIP-T42G/T41P: 1-Disabled X ranges from The default value is 0. Features->Forward & DND->DND ->Account 1 to 3.) account.X.dnd .on_code = (SIP-T46G: X It configures the DND on code for ranges from 1 account X when the DND mode is to 6. String configured to “custom”.
Appendix SIP-T42G/T41P: X ranges from 1 to 3. ) account.X.bus y_fwd.enable It enables or disables busy forward = feature for account X when the call forward mode is configured to (SIP-T46G: X ranges from 1 0 or 1 “custom”. to 6. 0-Disabled SIP-T42G/T41P: 1-Enabled X ranges from The default value is 0. Features->Forward & DND->Busy Forward->On/Off 1 to 3. ) account.X.bus y_fwd.
Yealink SIP-T4X IP Phones Auto Provisioning Guide account.X.tim eout_fwd.time out = (SIP-T46G: X ranges from 1 to 6. It configures the waiting ring time Integer from 0 to 20 before forwarding for account X when the call forward mode is configured to “custom”. The default value is 2. SIP-T42G/T41P: Features->Forward & DND->No Answer Forward-> After Ring Times X ranges from 1 to 3. ) account.X.alw ays_fwd.
Appendix ranges from 1 to 6. SIP-T42G/T41P: X ranges from 1 to 3. ) account.X.tim eout_fwd.off_c ode = It configures the no answer forward off (SIP-T46G: X code for account X when the call ranges from 1 String forward mode is configured to to 6. “custom”. SIP-T42G/T41P: The default value is blank. Features->Forward & DND->No Answer Forward ->Off Code X ranges from 1 to 3. ) account.X.tim eout_fwd.
Yealink SIP-T4X IP Phones Auto Provisioning Guide account.X.sub It enables or disables the phone to scribe_mwi = subscribe the message waiting (SIP-T46G: X ranges from 1 to 6. indicator for account X. 0 or 1 0-Disabled SIP-T42G/T41P: 1-Enabled X ranges from The default value is 0. Account-> Advanced-> Subscribe for MWI 1 to 3.) account.X.sub scribe_mwi_e xpires = (SIP-T46G: X ranges from 1 to 6. Integer from 0 to 84600 It configures the interval (in seconds) of MWI subscription for account X.
Appendix account.X.cp_ It configures the source callee identity source = for presentation for account X. (SIP-T46G: X ranges from 1 to 6. 0-RPID-FROM 0, 1 or 2 1-Dialed Digits SIP-T42G/T41P: 2-RFC4916 X ranges from The default value is 1. 1 to 3. ) account.X.ses sion_timer.ena It enables or disables the session timer ble = for account X. (SIP-T46G: X Account-> 0-Disabled Advanced-> to 6. 1-Enabled Session Timer SIP-T42G/T41P: The default value is 0.
Yealink SIP-T4X IP Phones Auto Provisioning Guide to 6. The default value is 0. SIP-T42G/T41P: X ranges from 1 to 3. ) account.X.srtp It configures whether to use voice _encryption = encryption service for account X. (SIP-T46G: X ranges from 1 to 6. 0-Disabled 0, 1 or 2 1-Optional SIP-T42G/T41P: 2-Compulsory X ranges from The default value is 0. Account-> Advanced->RTP Encryption (SRTP) 1 to 3. ) account.X.pti me = (SIP-T46G: X ranges from 1 to 6. 0 (Disabled), 10, 20, 30, 40, 50 or 60.
Appendix (SIP-T46G: X 0-Disabled ranges from 1 1-Enabled to 6. Pickup The default value is 0. SIP-T42G/T41P: X ranges from 1 to 3. ) account.X.gro up_pickup_co de = (SIP-T46G: X It configures the group pickup code for Account-> ranges from 1 account X. Advanced->Group The default value is blank. Call Pickup Code String to 6. SIP-T42G/T41P: X ranges from 1 to 3. ) account.X.dire ct_pickup_cod e= It configures the directed pickup code (SIP-T46G: X ranges from 1 String to 6. for account X.
Yealink SIP-T4X IP Phones Auto Provisioning Guide account.X.sub scribe_mwi_to It enables or disables the phone to _vm = subscribe to the voice mail for the (SIP-T46G: X ranges from 1 0 or 1 message waiting indicator for account Account-> X. Advanced-> to 6. 0-Disabled SIP-T42G/T41P: 1-Enabled X ranges from The default value is 0. Subscribe MWI To Voice Mail 1 to 3.) account.X.
Appendix X ranges from 1 to 3.) account.X.con f_uri = (SIP-T46G: X ranges from 1 to 6. String SIP-T42G/T41P: It configures the network conference Account-> URI for account X. Advanced-> The default value is blank. Conference URI X ranges from 1 to 3.) account.X.blf.s ubscribe_peri od = (SIP-T46G: X ranges from 1 to 6. Integer from 30 to 2147483647 It configures the period (in seconds) of the BLF subscription for account X. The default value is 1800. SIP-T42G/T41P: X ranges from 1 to 3.) account.
Yealink SIP-T4X IP Phones Auto Provisioning Guide (120~3600s) (SIP-T46G: X ranges from 1 to 6. SIP-T42G/T41P: X ranges from 1 to 3.) account.X.sip_ It configures the SIP server type for server_type = account X. (SIP-T46G: X 0-Default ranges from 1 to 6. 0, 2, 4 or 6 SIP-T42G/T41P: Account-> 2-BroadSoft Advanced->SIP 4-Cosmocom Server Type 6-UCAP X ranges from The default value is 0. 1 to 3.) account.X.
Appendix account.X.dtm f.dtmf_payloa d= (SIP-T46G: X ranges from 1 to 6. Integer from 96 to 127 It configures the RFC2833 payload for account X. The default value is 101. Account-> Advanced->DTMF Payload Type (96~255) SIP-T42G/T41P: X ranges from 1 to 3.) account.X.dtm It configures the DTMF info type when f.info_type = the DTMF type is configured as “SIP INFO” or “AUTO or SIP INFO” for (SIP-T46G: X ranges from 1 to 6. 1, 2 or 3 account X.
Yealink SIP-T4X IP Phones Auto Provisioning Guide X ranges from 1 to 3.) account.X.nat. It enables or disables NAT keep-alive udp_update_e for account X. nable = 0-Disabled (SIP-T46G: X Account-> 1-Default Advanced->Keep to 6. 2-Options Alive Type SIP-T42G/T41P: 3-Notify X ranges from The default value is 1. ranges from 1 0, 1, 2 or 3 1 to 3.) account.X.nat. udp_update_ti me = (SIP-T46G: X ranges from 1 to 6.
Appendix (2~40s) (SIP-T46G: X ranges from 1 to 6. SIP-T42G/T41P: X ranges from 1 to 3. ) account.X.adv anced.timer_t 4= It configures the session timer T4 (in (SIP-T46G: X ranges from 1 Float to 6. seconds) for account X. The default value is 5. Account-> Advanced->SIP Session Timer T4 (2.5~60s) SIP-T42G/T41P: X ranges from 1 to 3.) account.X.aler t_info_url_ena It enables or disables the distinctive ble = ring tones by the Alert-Info SIP header.
Yealink SIP-T4X IP Phones Auto Provisioning Guide X ranges from G726_24 G723_63; 1 to 3. Y G726_32 When Y=4, the default value is G729; G726_40 When Y=5, the default value is G722; iLBC (not When Y=6, the default value is iLBC; ranges from 0 to 13.
Appendix (SIP-T46G: X ranges from 1 to 6. Y ranges from 0 to 10. SIP-T42G/T41P: X ranges from 1 to 3. Y ranges from 0 to 13.) account.X.unr egister_on_re It enables or disables the phone to boot = de-register account X before reboot. (SIP-T46G: X ranges from 1 0 or 1 0-Disabled to 6. 1-Enabled SIP-T42G/T41P: The default value is 0. Account-> Advanced-> Unregister When Reboot X ranges from 1 to 3.) account.X.
Yealink SIP-T4X IP Phones Auto Provisioning Guide to 6. The default value is 0. SIP-T42G/T41P: X ranges from 1 to 3.) account.X.acd It enables or disables the phone to .available = display the available and unavailable (SIP-T46G: X ranges from 1 to 6. soft keys after the phone logs into the 0 or 1 ACD system. 0-Disabled SIP-T42G/T41P: 1-Enabled X ranges from The default value is 0. 1 to 3.) account.X.acd .
Appendix account.X.pict ure_info_enab It enables or disables the phone to le = download the picture information. (SIP-T46G: X 0-Disabled ranges from 1 0 or 1 1-Enabled to 6. The default value is 0. SIP-T42G/T41P: It is not applicable to SIP-T42G and X ranges from SIP-T41P IP phones. 1 to 3.) account.X.
