DECT IP Phone W60B & W56H Quick Start Guide(V81.30) www.yealink.com For W60B firmware 77.81.0.30 or later For W56H firmware 61.81.0.
W60 Package Contents Packaging Contents W56H Handset W60B Base Station Ethernet Cable Belt Clip Base Stand USB Charger Cradle Rechargeable Battery Quick Start Guide 2 Power Adapters Handset Protective Case (Optional) Note: Yealink W60 DECT IP phone consists of one W60B base station and one W56H handset.
W60B Package Contents W60B Base Station Base Stand Power Adapter Ethernet Cable Quick Start Guide Assembling the DECT Phone Packaging Contents 1. Connect the base station power and the network using Method a or Method b. a. AC Power Option b. PoE (Power over Ethernet) Option IEEE 802.3af compliant PoE Hub/Switch Note: If you choose Method a, use Yealink supplied power adapter (5V/600mA). A third-party power adapter may damage the base station.
2b. (Wall-Mount Installation) Attach the base station. MAC MAC SN SN 59m m 59m m 3. Insert the battery into the handset. battery 4. Attach the Belt Clip. 5. (Optional) Mount the charger cradle to the wall. 36.
6. Connect the charger cradle and charge the handset. Note: Use Yealink supplied power adapter (5V/600mA). A third-party power adapter may damage the handset. Check the charging status on the top right corner of the LCD screen. Getting Started Shortcuts Shortcut keys help you quickly access to frequently used phone features. Check the default shortcut keys below: 1 1 2 3 Press to place an internal call. 5 4 Press to decrease the ringer volume.
Handset Registration You can register up to 8 handsets to one W60B base station. Each handset can be registered to 4 different base stations. When the handset LCD screen prompts “Press base paging 2s then press Reg.”, long press on the base station till the registration LED flashes. There are two methods to register a new handset: Easy Registration: 1.Press the Reg soft key on the handset to register quickly. Normal Registration: 1.Press the OK soft key on the handset, and then select Register Handset.
Static If the base station cannot contact a DHCP server for any reason, you need to configure the IP address, subnet mask, gateway address, primary DNS address and secondary DNS address for the base station manually. To configure the network parameters for the base station manually: 1.Press the OK key to enter the main menu, and then select Settings->System Settings->Network (default PIN: 0000)->Basic. 2.Select the desired IP address mode from the IP Mode field. 3.
Handset Settings Handset Name To rename the handset: 1.Press the OK key to enter the main menu, and then select Settings->Handset Name. 2.Edit the value in the Rename field. 3.Press the Save soft key to accept the change. Volume Adjustment Press or Press or /earphone. when the handset is idle or ringing to adjust the ringer volume. during a call to adjust the receiver volume of speakerphone/earpiece Ring Tones 1.
To assign a speed dial number: 1.Press the OK key to enter the main menu, and then select Settings->Telephony-> Speed Dial. 2.Press or to highlight the desired digit key, and then press the Assign soft key. 3.Press to highlight the desired entry, and then press the OK soft key. or If both the office number and mobile number are stored, press the desired number, and then press the OK soft key again. or to highlight Basic Call Features Placing Calls To place a call directly: 1.
To place a call using the speed dial key: Long press the speed dial key to call the preset number directly. Answering Calls To answer a call, do one of the following: Press the Accept soft key. Press . Press . Press . Note: You can ignore an incoming call by pressing the Silence soft key or reject an incoming call by pressing . Ending Calls Press . Call Mute Press during a call to mute the call. Press again to un-mute the call.
Semi-Attended Transfer 1.Press the Options soft key during a call, and then select Transfer. 2.Enter the number you want to transfer the call to. 3.Press , or to dial out. 4.Press the Transfer soft key when you hear the ring-back tone. Attended Transfer 1.Press the Options soft key during a call, and then select Transfer. 2.Enter the number you want to transfer the call to. 3.Press , or to dial out. 4.Press the Transfer soft key after the call is answered.
About Yealink Yealink (Stock Code: 300628) is a global leading unified communication (UC) terminal solution provider that primarily offers video conferencing systems and voice communication solutions. Founded in 2001, Yealink leverages its independent research and development and innovation to pursue its core mission: “Easy collaboration, high productivity.” The company’s high-quality UC terminal solutions enhance the work efficiency and competitive advantages of its customers in over 100 countries.
