Electric Grass Trimmer & Edger model number 060-2279-2 | contact us: 1.866.523.5218 IMPORTANT: Read and follow all safety rules and operating instructions before using this product.
Specifications Table of Contents model no. 060-2279-2 | contact us: 1.866.523.5218 Specifications KNOW YOUR Trimmer Symbols Safety Information electrical information Exploded View Parts List Assembly operation MAINTENANCE Troubleshooting Warranty Type: Input: Feed: Speed: Line diameter: Cutting path: Weight: 2 3 4 5 7 8 9 10 12 16 17 18 Electric 120V, 60Hz, 5 amps Automatic dual line 8000 RPM (no load) 0.065” (1.65 mm) 14” (35.6 cm) 5 lb 12 oz (2.
Know Your Trimmer model no. 060-2279-2 | contact us: 1.866.523.5218 1 2 3 5 4 6 1. 2. 3. 4. 5. 6. 7. 8. Switch trigger Upper handle Cord retainer Auxiliary handle adjustment knob Auxiliary handle Split and telescoping shaft Edger guide Grass deflector 7 8 KNOW YOUR GRASS TRIMMER/EDGER The safe use of this product requires an understanding of the information on the product, this operator’s manual as well as a knowledge of the project you are attempting.
model no. 060-2279-2 | contact us: 1.866.523.5218 Symbols Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the product safely. Symbol Name Designation/Explanation V Volts Voltage. A Amperes Current. Hz Hertz Frequency (cycles per second). W Watts Power. min Minutes Time. Alternating Current Type of current. Direct Current Type or a characteristic of current.
model no. 060-2279-2 | contact us: 1.866.523.5218 • • • • • • • • • • • • • • • • • • This grass trimmer is designed for cutting grass and similar soft vegetation and for trimming grass edges in private and hobby garden areas which are not accessible with a lawnmower. The device is not designed for use in public gardens, parks, sports centres or at roadsides, nor in agriculture or forestry applications.
model no. 060-2279-2 | contact us: 1.866.523.5218 Safety Information ADDITIONAL SAFETY INSTRUCTIONS FOR YOUR GRASS TRIMMER • • • • • • • • • Do not expose to moisture. Use with only on AC power supply voltage shown on the product rating label. Avoid operating your trimmer in wet grass, where feasible. Take care not to lose your footing in wet grass. On slopes, be extra careful not to slip, and wear nonslip footwear. Do not walk backwards when trimming as you could trip. Walk never run.
GUIDELINES FOR USING EXTENSION CORDS • USE THE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause overheating. The table below shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.
Exploded View model no. 060-2279-2 | contact us: 1.866.523.
Item Description Drawing Qty 1 Plate 34103336 1 2 Cross-head screw ST4*12-F 3220313 18 3 Waterproof plug 36401504 1 4 Wire proof sheath 34201161 1 5 B-terminal 3650135 3 6 Trigger 34102719-1 1 7 Button spring 33401178 1 8 Jogging switch 36303152 1 9 Protecting jacket 34903161 2 10 Terminal 36503163 2 11 Left handle 34101717-1 1 12 Tube 31102725 1 13 Assist handle knob 34101185-2 1 14 Assist handle 31103725 1 15 Spring 36901720 1 16 Housing
Parts List model no. 060-2279-2 | contact us: 1.866.523.
model no. 060-2279-2 | contact us: 1.866.523.5218 Assemble the two halves of the • • Insert the lower shaft (2) into upper shaft (1). Turn the upper shaft (1) until lock button (1) clicks into place. Turn the lower shaft (2) collar until locked into place. • 1 2 AUXILIARY HANDLE • • 2 • 1 • Turn the handle lock knob (1) counterclockwise several turns to loosen the auxiliary handle (2). Adjust the handle position to provide the best level of balance and control for the operator.
model no. 060-2279-2 | contact us: 1.866.523.5218 Guard • • Assembly • • • • Stop the trimmer. Invert the grass trimmer to access the trimmer head. Using a cross-head screwdriver, remove the pre-installed screws (1) from the trimmer head. Place the guard (2) on to the trimmer head and turn the guard 45° following the track on the head. Align the screw hole on the guard with the screw hole on the trimmer head. Insert the screw into the trimmer head, fastening the guard in place.
model no. 060-2279-2 | contact us: 1.866.523.5218 The Cutting Line • A double-wound spool of monofilament cutting line is pre-installed on the grass trimmer. When the cutting line needs replacing, install a new spool. Use Yardworks® 60-2269-6 replacement spools. • Unplug the extension cord. Turn the grass trimmer over to access the spool (2). Remove the spool cover by pressing on two tabs parallel to each other on the side of the cover (1). Remove the spool (2) from the spool housing (3).
model no. 060-2279-2 | contact us: 1.866.523.5218 Operation refill the spool If you are unable to purchase a new pre-wound spool, you may purchase 0.065” (1.65 mm) nylon monofilament cutting line and refill the spool that was supplied with your grass trimmer. • Remove the spool from the trimmer head. • Cut a length of cutting line to approximately 20’ (6.1 m) long and fold it in half. • Loop the “V” end of the cutting line into the small notch on the inner rail of the spool to anchor the line.
model no. 060-2279-2 | contact us: 1.866.523.5218 To Turn On/Off Release the trigger switch (1). Allow at least 5 seconds for the cutting spool to stop rotating. Disconnect the extension cord if leaving unattended. Operation • • • 1 ! CAUTION: Allow 5 seconds or more for the grass trimmer to stop rotating after releasing the switch.Do not invert the grass trimmer or place your hands under the guard until the grass trimmer has come to a complete stop.
model no. 060-2279-2 | contact us: 1.866.523.5218 Edging function Operation This trimmer is equipped with an edging feature for use on sidewalks or walkways, patios and/ or driveways to clear over-grown grass from manicured surfaces. • • • Pull up edging coupler and turn handle end counterclockwise. Release edging shaft coupler when handle has been rotated 180°. Flip the edging guide down until it locks into place.
model no. 060-2279-2 | contact us: 1.866.523.5218 Split and telescoping tube Operation The shaft can be extended or shortened for ease of use. • Unscrew telescoping shaft coupler and slide to desired position. • Tighten telescoping shaft coupler.
model no. 060-1721-4 | contact us: 1.866.523.5218 Operation Lengthening the Line • While the grass trimmer is operating, the cutting line gets worn down and becomes shorter. This trimmer is equipped with an automatic lowercase, which automatically feeds additional line to the correct length as it wears down. • If the line does not automatically advance, the trimmer line may be tangled or empty. • To advance the line, restart the trimmer. Upon starting, the line will automatically advance.
model no. 060-2279-2 | contact us: 1.866.523.5218 Before each use • • Make sure the protective guard is tightly installed. Tighten the guard screws. Before trimming, inspect the area for string, wire, branches, or other material that may become entangled in the cutting line or thrown. • • • • • • • • Trim only when the grass and weeds are dry. Do not trim the grass at night. Always make sure you have adequate lighting.
model no. 060-2279-2 | contact us: 1.866.523.5218 Maintenance General MAINTENANCE Keep your grass trimmer clean and in good repair for maximum performance and service life. Before each use, inspect the switch and cord for damage. Check for damaged, missing, or worn parts. Check for loose screws, misalignment, moving parts that are jammed, or any other conditions that may affect the operation.
model no. 060-2279-2 | contact us: 1.866.523.5218 Tool runs slowly • • Check that the spool housing can rotate freely. Carefully clean it if necessary. Check that the cutting line does not protrude more than 4 1/2” (11 cm) from the spool housing. If it does, cut it off so that it just reaches the line trimming blade. Automatic line feed does not work. • • Press the tabs and remove the spool cover from the housing. Pull the cutting line until it protrudes 4 1/2” (11 cm) from the housing.
model no. 60-2279-2 060-2279-2 | contact | contact us:us: 1.866.523.5218 1.866.523.5218 TWO-YEAR LIMITED WARRANTY Warranty For TWO YEARS from the date of purchase within Canada, Yardworks CANADA will, at its option, repair or replace for the original purchaser, free of charge, any part or parts found to be defective in material or workmanship.
