NONRETURNABLE TO RETAILER THIS ITEM HAS BEEN CAREFULLY INSPECTED AT THE FACTORY FORAY DEFECTS, HOWEVER, IF YOU FIND YOU ARE MISSING ANY PARTS OR APART IS DEFECTED. PLEASE EMAIL US AT OR CALL (877) 533-5558, OUR CUSTOMER SERVICE TEAM IS THERE TO HELP! CUSTOMER SERVICE #(877) 533-5558 Hours of Operation: Monday — Friday from 9am —4pm PST.
SKU# 264-1227 Heavy-duty Drop Spreader MODEL # CT0085-75 A CAUTION-FOR YOUR SAFETY READ YOUR OPERATOR’S MANUAL COMPLETELY AND CAREFULLY BEFORE ATTEMPTING TO SET UP OR ASSEMBLE YOUR NEW DROP SPREADER. ALL OPERATORS OF THIS EQUIPMENT SHOULD READ AND UNDERSTAND ALL SAFETY RULES PRINTED ON THE MACHINE AND IN THIS OPERATOR'S MANUAL BEFORE USE.
PACKAGE CONTENTS Part | Description " “Quantity| Part| Description o Quantity A Hopper Assembly o E | Channel i 2 B Push Tube Flow Control Kit 1 C__ Stand Bracket i G | Clamp Reinforcement Bar 1 HARDWARE CONTENTS @ 20NN SR Y inner Hex Bolt smmx16mm . @ Inner Hex Bolt 16 mmx 6.
PREPARATION Before beginning assembly or operation of predict, make sure all parts are present. Compare parts with package contents list and diagram above. If any part is missing or damaged, do not attempt to assemble or operate the product. Contact customer service for replacement. Estimated assembly time: 15 minutes. Tools Required for Assembly: 4 mm Hex Wrench (included) Open-end Wrench (included) &> Helpful Tools for Assembly: Adjustable Wrench {not included) ~] ASSEMBLY INSTRUCTIONS 1.
4. Attach the reinforcement bar (H) to the hopper with one ram inner hex bolt (DD), one flat washer (HH) and one inner hex bolt (CC). Tighten with two & mm nylon nuts (GG). Thread one carriage bolt (BB) through the lower hole on the happier and sower tube (D). Tighten with one 6 mm nylon nut (GG). Hardware used 6 mmx 16mm @ Inner Hex Lott 6 mm x40 mm funner Hex Bolt 6 mm x 35mm @ Carriage Bolt 16 mmx 6.5 mm Flat Washer 5.
How to Adjust the outlet 1. Turn the drop spreader stand on its side. 2. Move the flow control handle to the “lock” position. 3. Look at the hopper bottom to check if the outlet is completely closed (fully overlapped by the shield). If there is any gap between the outlet and shield, please follow below steps to adjust: 4. Loosen the bolts on the flow control kit. 5. Move the flow control chamber back and forth till the gap is closed. Fix the position by re-tightening the nuts.
EXPLODED VIEW AND PART LIST Quantity| Part | Description Qlfafiiilyl Carriage Bolt 1 B Push Tube 1 CC 6 mmx40 mm Inner Hex Bolt | 1 € Stand Bracket Inner Hex Bolt 2 "D | Lower Tube Inner Hex Bolt 6 'E Channel Inner Hex Bolt 2 F Flow Control Kit Shylock Nut Clamp mmx 6.
*This three pages are flow setting guide, all spreaders and material may be different, please refer to the manufactures recommendations for settings MEDIA FLOW SETTINGS FLOW SETTINGS Some products may nol be available in all areas. The Table 115 a list of flow control settings for specific products avail Flow control settings are based on 3 mph forward speed. able for use with the spreader.
MEDIA FLOW SETTINGS Table 1: Flow Control Settings for Specific Fertilizer's, Insecticides, Grass Seeds (Contd) Ibs/1000 | Flow Control sg. ft. Setting Media 7 25 Howard Johnson All-purpose Fertilizer 10-10-10 7 25 Howard Johnson Ali-purpose Fertilizer 12-12-125 2 Maronite 1-0-0 4 2 Kay Soft Politicized Gypsum Coif Conditions 3 1.5 Kay Soft Pelleted Gypsum Soil Conditioner 2 1.5 Kay Soft Pelleted Gypsum Spit Conditioner 4 2 Les co Plus Fertilizer 26-0-7 4.2 2 Les co Starter Fertilizer 18-24-12 4.
MEDIA FLOW SETTINGS Table 1: Flow Control Settings for Specific Fertilizer's, Insecticides, Grass Seeds (Contd) 1bs/1000 | Flow Control ! sq. ft. Setting Media 6 3 Sam’s Choice Starter Fertilizer 20-27-6 3.6 2 Sam's Choice Starter Fertilizer 20-27-5 4 3 Scott Classic Grass Seed Fall Grass Seed Mix 2 2 Scott Classic Grass Seed Fall Grass Seed Mix 23 1.5 Scott Grub ex 3.1 2 Scott Grubber Season Long Grub Control 2.3 2 Scott Grub ex Season Long Grub Control 14 1.
