Safety Data Sheets (SDS)

Ingredient Material name TEEL-1 TEEL-2 TEEL-3
Ingredient Original IDLH Revised IDLH
US NIOSH Recommended
Exposure Limits (RELs)
calcium carbonate
Calcium carbonate, Natural calcium carbonate
[Note: Calcite & aragonite are commercially
important natural calcium carbonates.] / Calcium
carbonate, Natural calcium carbonate [Note:
Marble is a metamorphic form of calcium
carbonate.]
10 (total),
5 (resp)
mg/m3
Not
Available
Not
Available
Not Available
US OSHA Permissible
Exposure Levels (PELs) -
Table Z1
Bis
(2-ethylhexylthioglycolate)
dimethyltin
Tin, organic compounds 0.1 mg/m3
Not
Available
Not
Available
(as Sn)
US ACGIH Threshold Limit
Values (TLV)
Bis
(2-ethylhexylthioglycolate)
dimethyltin
Tin, organic compounds, as Sn 0.1 mg/m3
0.2
mg/m3
Not
Available
TLV® Basis: Eye & URT
irr; headache; nausea; CNS
& immune eff
US OSHA Permissible
Exposure Levels (PELs) -
Table Z1
methyltin tris(2-ethylhexyl
thioglycolate)
Tin, organic compounds 0.1 mg/m3
Not
Available
Not
Available
(as Sn)
US ACGIH Threshold Limit
Values (TLV)
methyltin tris(2-ethylhexyl
thioglycolate)
Tin, organic compounds, as Sn 0.1 mg/m3
0.2
mg/m3
Not
Available
TLV® Basis: Eye & URT
irr; headache; nausea; CNS
& immune eff
US OSHA Permissible
Exposure Levels (PELs) -
Table Z1
vinyl chloride Vinyl chloride 1 ppm 5 ppm
Not
Available
see 1910.1017;No employee
may be exposed to vinyl
chloride by direct contact
with liquid vinyl chloride.
US ACGIH Threshold Limit
Values (TLV)
vinyl chloride Vinyl chloride 1 ppm
Not
Available
Not
Available
TLV® Basis: Lung cancer;
liver dam
US NIOSH Recommended
Exposure Limits (RELs)
vinyl chloride
Chloroethene, Chloroethylene, Ethylene
monochloride, Monochloroethene,
Monochloroethylene, VC, Vinyl chloride
monomer (VCM)
Not
Available
Not
Available
Not
Available
Ca See Appendix A
EMERGENCY LIMITS
polyvinyl chloride Polyvinyl chloride 3 mg/m3 33 mg/m3 200 mg/m3
titanium dioxide (anatase) Titanium oxide; (Titanium dioxide) 10 mg/m3 10 mg/m3 10 mg/m3
calcium carbonate Limestone; (Calcium carbonate; Dolomite) 27 mg/m3 27 mg/m3 1300 mg/m3
titanium dioxide (anatase) N.E. mg/m3 / N.E. ppm 5,000 mg/m3
Bis (2-ethylhexylthioglycolate)
dimethyltin
Unknown mg/m3 / Unknown ppm 25 mg/m3
methyltin tris(2-ethylhexyl
thioglycolate)
Unknown mg/m3 / Unknown ppm 25 mg/m3
Exposure controls
Appropriate engineering
controls
Engineering controls are used to remove a hazard or place a barrier between the worker and the hazard. Well-designed engineering controls can be highly
effective in protecting workers and will typically be independent of worker interactions to provide this high level of protection.
The basic types of engineering controls are:
Process controls which involve changing the way a job activity or process is done to reduce the risk.
Enclosure and/or isolation of emission source which keeps a selected hazard 'physically' away from the worker and ventilation that strategically 'adds' and
'removes' air in the work environment.
Personal protection
Eye and face protection
Safety glasses with side shields
Chemical goggles.
Contact lenses may pose a special hazard; soft contact lenses may absorb and concentrate irritants. A written policy document, describing the wearing of
lenses or restrictions on use, should be created for each workplace or task. This should include a review of lens absorption and adsorption for the class of
chemicals in use and an account of injury experience.
Skin protection See Hand protection below
Hands/feet protection
The selection of suitable gloves does not only depend on the material, but also on further marks of quality which vary from manufacturer to manufacturer. Where
the chemical is a preparation of several substances, the resistance of the glove material can not be calculated in advance and has therefore to be checked prior
to the application.
The exact break through time for substances has to be obtained from the manufacturer of the protective gloves and.has to be observed when making a final
choice.
Suitability and durability of glove type is dependent on usage.
Experience indicates that the following polymers are suitable as glove materials for protection against undissolved, dry solids, where abrasive particles are not
present.
polychloroprene.
nitrile rubber.
butyl rubber.
Body protection See Other protection below
Other protection
Overalls.
P.V.C. apron.
Barrier cream.
Version No:1.0
Page 4 of 9
Vinyl compounds
Issue Date:09/08/2016
Continued...