SKU# 264-1222 125 LB. TOW BROADCAST SPREADER DO NOT RETURN TO STORE PLEASE CONTACT OUR CUSTOMER SERVICE TEAM IF YOU FIND YOU ARE MISSING ANY PARTS, APART IS DEFECTIVE, OR YOU HAVE ANY OTHER QUESTIONS/CONCERNS.
SKU# 264-1222 )Y;QRD {8513 1251B. TOW BROADCAST SPREADER A CAUTION-FOR YOUR SAFETY READ YOUR OPERATOR'S MANUAL COMPLETELY AND CAREFULLY BEFORE ATTEMPTING TO SET UP OR OPERATE YOUR NEW BROADCASTER SPREADER, ALL OPERATORS OF THIS EQUIPMENT SHOULD READ AND UNDERSTAND ALL SAFETY RULES FEINTED ON THE MACHINE AND IN THIS OPERATOR'S MANUAL BEFORE USE. Customer Service 1 Mall: ptiqservicous@@gmal .
A SAFETY INFORMATION Read the general safety operating precautions in your owing vehicle operator's manual for additional safety information. «This attachment is intended for use in lawn care and home applications. Do not tow behind a vehicle on a highway or in any high-spade application. Do not tow at spreads higher than maximum recommended towing speed. » Towing speed should always be slow enough 1o maintain control. Travel slowly over rough ground.
Protect Bystanders « Keep bystanders away when you operate a towed attachment. « Ba fore you back towing vehicle and attachment, look carefully behind attachment for bystanders. Keep Riders Off Towed Attachment « Kappa riders off of a towed attachment. « Riders an a towed attachment are subject to injury, such as being struck by objects and bang thrown off the attachment during sudden starts, stops and turns. « Riders abstract the operator's via, resulting in the attachment being used in an unsafe manner.
PACKAGE CONTENTS EMO O W . Closure Plate . Flow Control Kit . Hopper Assembly . Wheel (2) Axle Main Support Frame . U-tube A H. Hitch Bracket (2} |, Tongue J. Transmission S K. Spreading Fan L. Connect Clamp AA. Caver haft Service 533-5550 Mall: ptiqservicous@@gmal .
PACKAGE PACK SHOWN FULL SIZE NOT SHOWN FULL SIZE V N L Key Description Qty. Key Description Qty. 456 mm Hex Bolt 2 T |[25mmx83 mm Cotter Pin Shylock Nut 2 U 7 mmx 50 mm Otter Pin Invar Hax Bolt 1 V | Hitch Pin 1 P |6 mmx 45 mm Inner Hex Bolt 5 W |4mm Hex Wrench Thrust Washer B X Open-end Wrench Shylock Nut B Y Axle Bearing 2 8§ [19mm x 70 mm Hair Cotter Pin 16.5 mm Flat Washer 2 Customer Service 5 Mall: ptiqservicous@@gmal .
PREPARATION Before beginning assembly or operation of product, make sure all parts are present. Compare parts with package constants list and diagram above. If any part is missing or damaged, do not attempt to assemble or operate the product. Contact customer service for replacement, Estimated assembly time: 50 minutes. Tools Required for Assembly: 4 mm hex wrench (included) I_ Open-end ranch (included) 5—=% Helpful Tools for Assembly: Adjustable wrench —p ASSEMBLY INSTRUCTIONS 1.
3. (Pr-assembled by factory). Thread the spreading fan (K) onto the transmission shaft (J) and secure with 5 mm x42 mm cotter pin. Then spread end af of pin to secure. See figure 3. SX4% MM INTERROGATE TRANSMISSION SHAFT(J) FIGURE 3. 4. Insert the assembled transmission to the hole on the bottom of hopper assembly (C) with the LONG snout (with hole)is facing the left {(view from the front of the hopper ) to ensure the spreading fan (K) always spin sin counterclockwise direction.
5. Slide axle until lengths are equal, and install axle bearing (Y) on both sides to the axle and main support frame (F). See figure 5. 6. Install cotter pin (U)into side hole of transmission and axle. Then spread end of cotter pin. See figure 5. 7.Install wheels (D) onto both ends of the axle. Important: For a smooth assembly of the wheals, pleads make sure the wheal tubes are aligned with the axle straighten line, slightly wobble the wheels to adjust till axle ends comes out. 8.
11. Slide the closure plate (A} anti the channels under the hopper bottom with {ab of the closure plate facing down. See figure B. 12. Connect tongue (I) to main support frame (F)with the connect clamp (L). Secure with two 8 mm X 456 mm hex bolts (M) and 8émm nylon nuts See figure 9. 13. Connect the flow contra rod to the tab on the closure plate (BB) with inner hex bolt (Q), thrust washer (Q). Secure with 6§ mm nylon nut (R). Tighten. See figure 9. 14, (Pr-assembled by factory).
HOW TO ADJUST THE CLOSURE PLATE If the closure plate cannot be closed complacently, please follow steps helot for adjusting: 1. Move the flow contralto lever to the “lack” (OFF) position. 2. Look inside the hopper to sack if the closure plate is complacently closed, if there is any gap between the closure plate and outlet of hopper, please follow below steps ta adjust: 3. Loosen the bolts on the flow control chamber. 4.
OPERATION INSTRUCTIONS OPERATION Daily Operating Checklist O Check far Nose or missing hardware. O Make sure all connections are tight. O Make sure attachment responds properly ta controls. 0O Hack for debris build-up that could obstruct proper meson of the spreader control components. Operating the Spreader The fan speed and the spread width are controlled by the speed of the vehicle. The recommended operating speeds 3 mph, which is slightly faster than that of a brisk walk.
PART LIST AND EXPLODED VIES Part Description Quality | Part Disciplinarian Quantity A Closure Plate Shylock Nut 2 B Flow Control Kit 1 Q 6x16 mm Inner Hex Alt 1 C Hopper Assembly 1 v Hitch Pin 1 D Wheal 2 P 6 x45 mm Inner Hex Bolt 5 E Axle Thrust Washer 8 F Main Support Frame (Hopper) Shylock Nut 8 G U-tube 1 S 18 x70 mm Hair Cotter Pin 1 H Hitch Bracket Hair Cotter Pin 1 1 Tongue Cotter Pin 4 d Transmission Shaft Hex Wrench 1 K Spreading Fan 1 X Open-end Wrench 2 L Connect Clamp 1 Y Axle Bearing 2 AA | Cov
MEDIA FLOW SETTINGS Table 1: Flow Control Settings for Specific Fertilizer's, Insecticides, Grass Seeds (Contd) | Flow Control eq. f. Setting Media 4 2 Les co Pr-M.
