SKU #264-1223 85LB. TOW BROADCAST SPREADER MODEL # BS0001-85 DO NOT RETURN TO STORE PLEASE CONTACT OUR CUSTOMER SERVICE TEAM IF YOU FIND YOU ARE MISSING ANY PARTS, APART IS DEFECTIVE, OR YOU HAVE ANY OTHER QUESTIONS/CONCERNS.
SKU #264-1223 85LB. TOW BROADCAST SPREADER N Velez T el T MODEL # BS0001-85 & CAUTION-FOR YOUR SAFETY READ YOUR OPERATOR'S MANUAL COMPLETELY AND CAREFULLY BEFORE ATTEMPTING TO SET UP OR OPERATE YOUR NEW BROADCAST SPREADER. ALL OPERATOR OF THI® EQUIPMENT SHOULD READ AND UNDERSTAND ALL SAFETY RULES PRINTED ON THE MACHINE ANC IN THIS OPERATOR'S MANUAL BEFORE USE. Customer Service 1 Mall: ptiqservicous@@gmal .
A\ SAFETY INFORMATION Read the general safety operating precautions in your towing vehicle operator’s manual for additional safety information. * This attachment is intended for use in lawn care and home applications. Do not tow behind a vehicle oh a highway or in any high-speed application. Do not tow at speeds higher than maximum recommended towing speed. « Towing speed should always be slow enough to maintain control. Travel slowly over rough ground.
Protect Bystanders * Keep bystanders away when you operate a towed attachment. «Before you back towing vehicle and attachment, look carefully behind attachment for bystanders. Keep Riders Off Towed Attachment «Keep riders off of a towed attachment. =Riders on a towed attachment are subject to injury, such as being struck by objects and being thrown off the attachment during sudden starts, stops and turns. ~ Riders obstruct the operator's view, resulting in the attachment being used in an unsafe manner.
PACKAGE CONTENTS A. Flow Control Kit H. High Bracket (2) B. Connect Clamp 1. Tongue C. Hopper Assembly J. Transmission Shaft D. Wheal (2) K. Axle Bearing (2) E. Axle L. Spreading Fan BB. Cover F. Main Support Frame CC.Closure Plate BB G.
HARDWARE PACK SHOWN FULL SIZE ([W NOT SHOWN FULL S1Z2E Key Description Qty. Key Description Qty. Hex Belt 2 U [25mmx 63 mm Cotter Pin Hex Bolt 2 V |7 mmx 50 mm Cotter Pin 3 O Shylock Nut 4 W[5 mmx42mm Cotter Pin Inner Hex Bolt 1 X Hitch Pin 1 Q (6mm x 40 mm Inner Hex Bolt 4 Y |4 mm Hex Wrench 1 R |16 mm mm Thrust Washer 5 z Open-end Wrench 2 S |(6mm Lockout mmx16.5 mm Flat Washer mmx70 mm Hair Counterpoint 1 Gusto! 5 antimacassar Mall: ptiqservicous@@gmal .
PREPARATION Be fare beginning assembly or operation of product, make sure all parts are present. Compare parts with package contents ills and diagram above. If any part is missing or damaged, do not attempt to assemble or aerate the product. Contact customer service far replacement. Estimated assembly time: 50 minutes. Tools Required for Assembly: 4 mm hex wrench (included} — Q Open-end wrench {included) 5—= Helpful Tools for Assembly: Adjustable wrench — ASSEMBLY INSTRUCTIONS 1.
3. Insert the transmission shaft with fan (J}into the hole on the bottom of hopper assembly (C). See figure 3. 4. Insert four inner hex belts (Q) through four thrust washers (R), the hopper assembly (C), and frames (F &6). Secure the bot torn of the bolts wile four 8 mm locks (S). To avoid damage to plastic washer, do not overnight the bolts and nuts . See figure 3. BOTTOM HOLE OF HOPPER 5. Slide axle (E) until lengths are equal. See figure 4. FIGURE 4. 6. Install wheels (D) lento both ends of the axle {E).
. Install hair cotter pin (Tintoretto top af transmission shaft (the cotter pin is designed to agitate the fertilizer). See figure 6. o TOP OF TRANSMISSION HAFT N FIGURE 6. 10, Slide the closure plate (CC) inch the channels under the hopper bottom with tab of the closure plate facing down. 8ee figure 7. FIGURE 7. Customer Service 8 Mall: ptiqservicous@@gmal .
11. Connect tongue (1) to main support frame (F) with connect clamp (B). Secure with two hex bolts (M), two B mm nylon nuts(Q). Tighten. See figure 8. 12, Connect the flow control rod (A) to the tab on the closure plate (CC) with inner hex bolt (P), thrust washer (R). Secure with 6 mm nylon nut (S). Tighten. See figure A. 13. Assemble the hitch brackets (H) to the tongue () with two hex bolts {N) and 8 mm lackey nuts (O). Tighten. See Figure 9.
HOW TO ADJUST THE CLOSURE PLATE If the closure plate cannot be closed completely, please follow steps below for adjusting: 1. Move the flow control lever to the *lock” (OFF) position. 2. Look inside the hopper to check if the closure plate is completely closed, if therein gap between the closure plate and outlet of hopper, please follow below steps to adjust: 3. Loosen the bolts on the flow control chamber. 4.
OPERATION INSTRUCTIONS OPERATION Daily Operating Checklist O Check far Nose or missing hardware. O Make sure all connections are tight. O Make sure attachment responds properly ta controls. 0O Hack for debris build-up that could obstruct proper meson of the spreader control components. Operating the Spreader The fan speed and the spread width are controlled by the speed of the vehicle. The recommended operating speeds 3 mph, which is slightly faster than that of a brisk walk.
PART LIST AND EXPLODED VIEW Part Description Quantity | Part Description Quantity A Flow Control Kit 1 P 6mm x16 mm Inner Hex Bolt 1 B Connect Clamp 1 X Hitch Pin 1 C Hopper Assembly Inner Hex Bolt 4 D Wheel 2 R 168 x 7 mm Thrust Washer 5 E Axle Shylock Nul S F Main Support Frame (Hopper) Hair Cotter Pin 1 G U-tube Hair Co tier Pin 1 H Hitch Bracket Cotter Pin 3 1 Tongue Coulter Pin 1 J Transmission Hex Wrench 1 K Axle Bearing 2 Z Open-end Wrench 2 L Spreading Fan 1 AA 3Zmm x 16.
MEDIA FLOW SETTINGS Table 1: Flow Control Settings for Specific Fertilizers, Insecticides, Grass Seeds (Contd) Ibs/1000 | Flow Control &q. ft. Setting Media 4.