4” (36 CM) BRUSHLESS GRASS TRIMMER model number 060-1984-8 | contact us: 1.866.523.5218 3026035 IMPORTANT: Read and follow all safety rules and operating instructions before using this product.
model no. 060-1984-8 | contact us: 1.866.523.
Introduction 4 Safety Instructions & Symbols 5 Product Specifications 9 Product Diagram 10 Assembly 11 Operating Instructions 12 Maintenance 18 Storage 18 Troubleshooting 19 Exploded View 20 Parts List 21 Warranty 22 Table of Contents model no. 060-1984-8 | contact us: 1.866.523.
model no. 060-1984-8 | contact us: 1.866.523.5218 Please do not operate garden equipment near children. This could lead to severe injury or death. Introduction INTRODUCTION Congratulations on your purchase of your new Yardworks® tool. It has been designed, engineered and manufactured to give you the best possible dependability and performance. Should you experience any problem you cannot easily remedy, please contact our Yardworks® customer service line at 1.866.523.5218.
FOR ALL APPLIANCES • • • • • • • • • • • • Avoid dangerous environments — do not use appliances in damp or wet locations. Don’t use in rain. Keep children away — all people and pets should be kept at a distance from the work area. Dress properly — do not wear loose clothing or jewellery. They can be caught in moving parts. Wear protective clothing; use of work gloves, long pants, a long-sleeved shirt and safety footwear is recommended when working outdoors.
Safety Instructions model no. 060-1984-8 | contact us: 1.866.523.5218 7. 8. 9. 10. 11. ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns. Do not use a battery pack or appliance that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.
p) After extended periods of storage, it may be necessary to charge and discharge the battery pack several times to obtain maximum performance. q) The battery pack gives its best performance when it is operated at normal room temperature (20°C ± 5°C/68°F ± 9°F). r) When disposing of battery packs, keep battery packs of different electrochemical systems separate from each other. s) Recharge only with the charger specified by Yardworks® .
model no. 060-1984-8 | contact us: 1.866.523.5218 Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the product effectively and safely.
TECHNICAL DATA Voltage Speed Cutting Diameter Line Diameter Line length Battery capacity (060-1987-2) Charger Input(060-1990-2) 48V high: 6000/min low: 4500/min 14" (36 cm) 0.080" (2.0 mm) 2x8 ft (4.9 m) 2.0 Ah 120 V~, 60 Hz, 110 W Charger Output(060-1990-2) Charging time Machine Weight ,2A 48 V 1 hr 11 lb 8 oz (5.2 kg) SUITABLE BATTERY PACKS Item 060-1987-2 ABP4830SH 060-1988-0 ABP4850SH 060-1989-8 Number Battery 2.0 Ah 3.0 Ah 4.0 Ah 5.0 Ah 6.
Product Diagram model no. 060-1984-8 | contact us: 1.866.523.5218 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. Battery pack (060-1987-2) Battery pack release button On/Off switch Lock-off button Two-speed gear control Auxiliary handle Couplings Safety guard Line cutter Trimmer head Spool Bump knob Charger (060-1990-2) Hex key (Fig. A2) Bolt x 5 (Fig.
model no. 060-1984-8 | contact us: 1.866.523.5218 To reduce the risk of injury, user must read instruction manual. 1. Assembling the upper shaft and lower shaft Connect the couplings into each other (see Fig. A1). Align the holes and fasten the couplings by screwing the bolt with hex key (see Fig. A2). 14 A1 A2 15 B 2. Assembling the Auxiliary handle Place the auxiliary handle onto the shaft and align with the anti-vibration circle on the shaft.
A1 A2 model no. 15060-1984-8 | contact us: 1.866.523.5218 Operation 3. Assembling the safety guard Attach the safety guard to the trimmer head. Align the guard so it slides into the slots located on the trimmer head (see Fig. C1.). Secure the safety guard onto the trimmer head with the screw provided (see Fig. C2.). B C1 C2 BEFORE OPERATION 1.
model no. 060-1984-8 | contact us: 1.866.523.5218 A1 D A2 15 CHARGING INDICATOR This charger is designed to detect some problems that can arise with battery packs. Indicator lights indicate problems (see table below). Light ON/ Flash Status Defective battery. Red on Battery Temperature Protection. The temperature of battery pack is less than 0oC (32oF) or more than 40oC (104oF). B Red flash Fully charged. Green on Charging. Green flash 2.
C1 C2 model no. 060-1984-8 | contact us: 1.866.523.5218 Operation Instructions 2 2 1 1. SWITCH ON/OFF To switch on, 1 press the lock-off button first, then the On/Off switch (see Fig. F). To switch off, release the On/Off switch. 2. TWO-SPEED GEAR CONTROL The trimmer has a two-speed gear control designed for working at Low (mark is 1) or High (mark is 2) speeds (see Fig. G). Select either Low or High speed according to the required working condition. E2 E1 2 LOW 1 High F G 3.
1 1 2 LOW 15 1 High E2 E1 2 F G LOW 1 High F G 300 H1 H2 300 H1 H2 H3 H4 3 4. Adjusting cutting line length 2 The trimmer head allows the operator to release more cutting line without stopping the motor. As line becomes frayed or worn, additional line can be released by lightly tapping the bump knob on the ground while operating the trimmer (see Fig. I). NOTICE: Line release will become more difficult if the line cutter becomes dull.
model no. 060-1984-8 | contact us: 1.866.523.5218 00 H3 Operation Instructions H2 H4 5. To replace the spool and line 3 For your convenience it is recommended you buy a replacement spool with line. 2 Press and hold in the two cap release latches. Loosen the cap by rotating it counterclockwise. Pull cap away from the spool holder (see Fig. J1). Remove old spool (see Fig. J2). Place new spool into cutting head. Release one line from cleat and feed line through eyelet 1 (see Fig. J3).
J2 J3 model no.1060-1984-8 | contact us: 1.866.523.5218 6. To replace the line only Take a line of approximately 16’ (5 m). Insert the centre point of line into the notch in the middle section of the spool and wind the line in a clockwise direction (see Fig. K1). Care should be taken to ensure that the line is neatly coiled on the spool. Failure to do so will impair the efficiency of the automatic bump line feed (see. Fig. K2). Then fit spool as described in “To replace the spool and line” on page 16.
model no. 060-1984-8 | contact us: 1.866.523.5218 Maintenance MAINTENANCE Always check the product prior to being used for any damage. After use, disconnect the battery from the tool and check for damage. Your power tool requires no additional lubrication or maintenance. There are no user serviceable parts in your power tool. Never use water or chemical cleaners to clean your power tool. Wipe clean with a dry cloth. Always store your trimmer in a dry room. Keep the motor ventilation slots clean.
model no. 060-1984-8 | contact us: 1.866.523.5218 Problem Trimmer fails to operate. Possible Cause Corrective Action Battery discharged. Recharge battery; also see the content in charger manual. Allow to cool/warm. Contact Yardworks® at 1.866.523.5218. Contact Yardworks® at 1.866.523.5218. Battery too hot/cold. Motor is broken. Internal wiring of machine damaged. Motor is broken. Battery not fully charged. On/Off switch defective. Machine defective. Line spool is not wound well.
51 50 49 49 48 48 47 53 53 54 52 52 55 55 56 57 57 58 58 59 59 46 45 44 43 42 Exploded View 20 20 model no. 060-1984-8 | contact us: 1.866.523.
No.
model no. 060-1984-8 | contact us: 1.866.523.5218 FIVE-YEAR LIMITED WARRANTY Warranty For five (5) years from the date of purchase within Canada, YARDWORKS CANADA will, at its option, repair or replace for the original purchaser, free of charge, any part or parts found to be defective in material or workmanship (excludes battery).
model no. 060-1984-8 | contact us: 1.866.523.5218 FCC Part 15 Supplier’s Declaration of Conformity Product Description: 48V 2.0 A Charger Model Number: 060-1990-2 Trade Name: Yardworks® This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Responsible Party: Positec USA, Inc.
1 14” (36 CM) BRUSHLESS GRASS TRIMMER model no. 060-1984-8 | contact us: 1.866.523.5218 Quick Start Guide 1. ASSEMBLING THE UPPER SHAFT AND LOWER SHAFT Connect the couplings together. (See Fig. A1) Align the holes and fasten the couplings by tightening the bolt with hex key. (See Fig. A2) A1 2. ASSEMBLING THE AUXILIARY HANDLE A2 B Place the auxiliary handle onto the shaft from the top, and align with the anti-vibration circle on the shaft.
2 14” (36 CM) BRUSHLESS GRASS TRIMMER model no. 060-1984-8 | contact us: 1.866.523.5218 OPERATION 1. CHARGING THE BATTERY (SEE FIG. D ) D 2. INSTALLING AND REMOVING THE BATTERY PACK Slide the battery pack into tool’s battery port. A simple push and slight pressure will be sufficient. Press the battery pack latch and remove the battery pack from the tool. (See Fig. E) E 2 1 * This information is provided for your convenience. It does not replace the instruction manual 2 and safety instructions.
