iti YARDMAN %& => 2-in-1 Chipper Operator's Manual MODEL NUMBER YW6065 SERIAL NUMBER PURCHASE DATE Doth model number and serial the rusher may be fun rain label, Ye Both of thew future use.
Your ne wld design YARDMASTER chipper offers qu and safe ta operate.
se] ee] $1 MODEL AND SERIAL NUMBERS Carefully read troubleshot epithet sellotapes pianola Toe fore Rising your view tir, Poy attention to all cations Record the model and serial number as well as date natl linings. and place of purchase for future reference. Have this information available wham ordering parts or optional accessories and when making ie | or warranty inquiries. AN This unit fo cut wood into chips.
se] ee] SPECIFICATIONS Model Number. Engine Welsh Yardman Misplacement Zia Start Type CAPRICE Approval Re coll Yes Wood Diameter 41 Fas Ripe Cavity Number of Blades 2 Replaceable Blades Mes Bag included Discharge Chi Material Ste Weight 1108s SAFETY GENERAL SAFETY RULES UNDERSTAND YOUR MACHINE Read this manual and labels affixed to the machine to understand its limitations and potential hazards. Be thoroughly familiar with the controls and their proper operation.
5 Keep children, pats, and other people not using the unit away from the work area. Be alert and shut off unit if anyone enters work ares, seep children under the watchful care of a responsible adult. Dio vot operate the machine while under the influence of drugs, alcohol. or any medication that could affect your ability to use it properly. Dress properly, Wear heavy long pants, boots, and gloves. Do not wear loose lathing, hart pants, ar jewelry of any kind.
Replace all fel nk snd container caps secondhand Wine tp spilled fuel Never orate the unit invidious the fuse cp secularization: ibid GF Eating 5 Cotton of Ignition To Pilled Baal TF RIEL is spiff do not attempt to start the engine but move the machine ways from the area af spillage and avoid creating any source of ignition until fuel vapors have dissipated When dust is spilled an yourself or your clothes, wash your skin and change clothes immediately.
his machine is self-feeding, do not force branches into the blades. Allow the machine to asthmatically feed through. Allow time for the machine to reach the highest spinning revolutions before fending the next load of branches. UNCLOGGING Never allow processed material to build up in the discharge area. This can prevent proper discharge and result in Kickback from the chipper hopper. Never attempt to unclog dither the feed hopper or discharge chute white the engine is running.
se] ee] CONTENTS SUPPLIED REN A I 101 Operator's Manual § Engine Manta! Your YARDMAN chipper comes partially assembled and contains the following: Main Machine . Wheels [1 pair) Chipper Cone Deflector Handle . kickstand Rod Wheel Shaft Collection Hag Engine Cif PARACETAMOL 2306 11.
ASSEMBLY “This chipper was partially assembled at the factory, following the below assembly instructions to do assembling. WHEELS 1. Slide a wheel assembly onto each end of the stub axle as seen in Figure 1 Frustration 1 Place the flat washer anti exposed axle.
= ind Chipper + Operator's Manual KICKSTAND ROD CHIPPER CONE Ali the Top of the Bookbinder rod oles willy the ted holes on this Align the three holes of the chipper fa take cone to the three studs Angie oun plate See Figure 3, Frustration' £1 Use the Boo Mbabane on the rotatory disc housing. (See Figure 4, Bust ration 1) Secure the its Flat washer Tan tine orn Flavored In 60 aerie te intake cone with the ME nuts from Hardware Kit#4, {See Figure 4, kickstand.
HOPPER HANDLE COLLECTION BAG Align the holes of the handle bar assembly with the holes on the 1H headset adjusting wing nt to set the distracted shoot too shredder hopper opening. {See Figure & castration 1) Then, secure {snd Figs 7 limitation 1) the handle assembly to the hopper opening with the M820 bolts, washers, and nuts feo Hardware Kit #6 shown in Figure 6 Castration 2. 2. Open the debris bag and slip the opening of the debris hag over the discharge chute housing. {See Fig. 7 illustration 2) 3.
FEED HOPPER The Feed Hopper is on top the unit. Always load W eaves and other it waste into the hopper opening. Ever wet hands into the hopper opening. CHIPPER CONE Tre Chipper Cone fs located on the front of the unit, and > went ta the engine. Insert branches and tree Bombs no % forger than 3" (7.60mi in diameter bit the chipper Cong opening. Ever insert hands past the cone opening. COLLECTION BAG The Collection Bag captures all debris discharged » from the unit.
se] ee] STOP ENGINE Sudden slapping at high Ta stop the engines tse the following procedure. A WARNING need under a heavy Toad is of A Moss the Eves fo stop position. PE 2 Ese fuel shutoff valve, SWE unt the machine complicatedly stops: Allow the engine to completely cool: Hanover the engine's spark plug Then clean aut the interior of the machine and its discharge chutes TRANSPORTING Your BARNYARD chipper is emitted with fw large wheels for easy movement by hand.
HAMMER SLICE CHECK Remove the rotor housing cover and cover plate shown in Figure and S-type hammer slicer. If 8. Check the triangle hammer sic one or both are damaged, replacement is recommended. Figure 8 KNIFE CHECK Remove the chipper cane from the unit and rotate the cutting disc to inspect the sharpness of the knives. {See Figure 9) 17 [ matte nonce KNIFE INSPECTION CHE GA the SRR SE the RE Taine rally (Sed Ogle 10) will Auspices chippy operating loyalism.
se] ee] 4. Detach the rotor housing and hopper firm the rotor disc seat. 7. If the hammer slicers are damaged, remove the four M1Ix55 lots that hard the 1-type hammer slicer and triangle hammer slicer, and replace {See Figure 14) J-Type Hammer Slice Triangle Hansen Slice Figure 14 8. If knife show signs of wear, replace it. Using the 8mm hex weeds, peach photo Uwe own housing aod remove the Deg Figure 12 casket heat cap screws and the chipper knife.
KNIFE RESHARPENING After removal, the knives should be sharpened on a surface grinder. Be careful and wear gloves To protect our hands. is extremely Important to consistently maintain the 38-degree cutting angle for proper performance. Marks sure there fs plenty of coolant wed during the grinding process, since excessive heat damages the knives and weakens the metal.
se] ee] TROUBLESHOOTING Problem Remedy 1. Attach spark plug wire securely fo Sok pli wire = dispersion ied . spark plug | Out of uel stile hel 2. Fill with clean, fresh gasoline Erse snd fe he not 3. Engine and Fuel valve must Croce } tbe in CLOSE posit level must ban position Engine fails to start LC Michelle nol LEE edition for a cold start Blocker line fountainhead 6. Clean, adjust gap, or replace | Freieieodie 7. Wait few minutes to restart, but do Moon ninepin not prime 5. Clean fuel line 8.
